Nissan Juke (2014 year). Service Repair Manual — part 60
POWER DOOR LOCK SYSTEM
DLK-185
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
The automatic door lock function ON/OFF can be switched by performing the following operation.
1.
Close all doors (door switch OFF)
2.
Turn ignition switch ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.
4.
The switching is completed when the hazard warning lamp blinks.
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (UNLOCK OPERATION)
The automatic door lock/unlock function is the function that unlocks all doors linked with the key position or
shift position. It has 3 types as follows.
IGN OFF Interlock Door Unlock
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.
Key out Interlock Door Unlock
When ignition key is removed from ignition knob switch, all doors unlock.
When BCM detects that ignition key is removed from ignition knob switch, BCM transmits unlock signal to all
door lock actuators.
P Range Interlock Door Unlock*
All doors are unlocked when shifting the selector lever from any position other than the P to P position.
BCM outputs the unlock signal to all door lock actuators when it detects that the ignition switch is in the ON
position and the shift signal received from TCM via CAN communication is shifted from any position other than
the P to P position.
Setting change of Automatic Door Lock/Unlock Function
The unlock operation setting of the automatic door lock/unlock function can be changed.
With CONSULT
The ON/OFF switching of the automatic door lock/unlock function and the type selection of the automatic door
lock/unlock function can be performed at the WORK SUPPORT setting of CONSULT.
Without CONSULT
The automatic door lock/unlock function ON/OFF can be switched by performing the following operation.
1.
Close all doors below (door switch OFF)
2.
Turn ignition switch ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.
4.
The switching is completed when the hazard warning lamp blinks.
*: This function does not operate on M/T models.
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
Revision: 2013 October
2014 JUKE
DLK-186
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY SYSTEM
REMOTE KEYLESS ENTRY SYSTEM
System Diagram
INFOID:0000000009754114
System Description
INFOID:0000000009754115
DOOR LOCK AND UNLOCK OPERATION
• When door lock and unlock button of keyfob is pressed, door lock and unlock signal transmits from keyfob to
BCM via remote keyless entry receiver.
• When BCM receives the door lock and unlock signal, it operates door lock actuator, blinks the hazard lamp
at the same time as a reminder.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unlock operation is performed if the keyfob is operated.
OPERATION AREA
To ensure that the keyfob works effectively, use within 1 m (3 ft) range of each door, however the operable
range may differ according to surroundings.
SELECTIVE UNLOCK FUNCTION
• When an LOCK signal is transmitted from keyfob, all doors are locked.
• When an UNLOCK signal is transmitted from keyfob once, driver side door is unlocked.
• Then, if an UNLOCK signal is transmitted from keyfob again, all other doors are unlocked.
How to change selective unlock mode.
With CONSULT
Selective unlock mode can be set to ON or OFF using CONSULT.
Refer to
DLK-189, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Without CONSULT
• ON/OFF can be switched when keyfob lock button and unlock button are pressed simultaneously for 5 sec-
onds or more while steering lock is locked.
• When mode is switched, hazard warning lamp blinks.
HAZARD AND HORN REMINDER FUNCTION
When doors are locked or unlocked by keyfob, BCM blinks hazard warning lamps as a reminder and transmits
horn chirp signal to IPDM E/R. IPDM E/R sounds horn as a reminder.
The hazard and horn reminder has a horn chirp mode (C mode) and a non-horn chirp mode (S mode).
Operating Function of Hazard and Horn Reminder
JMKIA6162GB
Remote controller operation
Operation condition
Lock/unlock
Ignition key is removed from ignition key cylinder
OFF
→
ON
: 3 blinks
ON
→
OFF
: 1 blink
Revision: 2013 October
2014 JUKE
REMOTE KEYLESS ENTRY SYSTEM
DLK-187
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Hazard and horn reminder does not operate if ignition switch ON position.
How to change hazard and horn reminder mode
With CONSULT
DLK-189, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Without CONSULT
When LOCK and UNLOCK signals are sent from the Intelligent Key for more than 2 seconds at the same time,
the hazard and horn reminder mode is changed and hazard warning lamp blinks and horn sounds as per the
following items:
AUTO DOOR LOCK FUNCTION
After door is unlocked by keyfob button operation and if 1 minute or more passes without performing the fol-
lowing operation, all doors are automatically locked. However, operation check function does not activate.
Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
189, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
PANIC ALARM FUNCTION
When key switch in the OFF position, BCM transmits horn reminder signal to IPDM E/R. Then, IPDM E/R
turns on and off horn intermittently. Refer to
SEC-134, "VEHICLE SECURITY SYSTEM : System Description"
.
INTERIOR ROOM LAMP CONTROL FUNCTION
Interior room lamp is controlled according to door lock/unlock state, refer to
CONTROL SYSTEM : System Description"
C mode
S mode
Keyfob operation
Lock
Unlock
Back door
open
Lock
Unlock
Back door
open
Hazard warning lamp blinks
Twice
Once
—
Twice
—
—
Horn sound
Once
—
—
—
—
—
JMKIA6362GB
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Key switch is ON
Revision: 2013 October
2014 JUKE
DLK-188
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER SYSTEM
BACK DOOR OPENER SYSTEM
System Diagram
INFOID:0000000009754116
System Description
INFOID:0000000009754117
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not
open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are
in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• When back door is unlocked using back door opener request switch (selective unlock
mode), or after BCM outputs all doors unlock signal
• Vehicle speed is less than 5 km/h (3 MPH)
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM)
DLK-189
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010295439
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
DOOR LOCK
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)
INFOID:0000000009754119
WORK SUPPORT
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioning system
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
TPMS
AIR PRESSUE MONITOR
×
×
×
Revision: 2013 October
2014 JUKE
DLK-190
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*: P range interlock door lock/unlock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function can be changed to operate with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other
than the P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to
OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON
to OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position
other than the P to P position
• MODE 5: Driver side door is unlocked when key out of key switch
• MODE 6: All doors are unlocked when key out of key switch
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function can be selected from the following in this mode
• Off: Non-operation
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Door lock and unlock operation
Monitor Item
Contents
IGN ON SW
Indicated [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicated [On/Off] condition of key switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicated [On/Off] condition of back door switch
LOCK STATUS
Indicated [On/Off] condition of front door driver side
ACC ON SW
Indicated [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicated [On/Off] condition of lock signal from key fob
KEYLESS UNLOCK
Indicated [On/Off] condition of unlock signal from key fob
KEY CYL LK-SW
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
Indicated [On/Off] condition of unlock signal from door key cylinder
VEHICLE SPEED
Display the vehicle speed signal received from combination meter by numer-
ical value [Km/h]
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM)
DLK-191
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
MULTI REMOTE ENT
MULTI REMOTE ENT : CONSULT Function (BCM - MULTI REMOTE ENT)
INFOID:0000000009754120
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
WORK SUPPORT
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is
touched
• The back door lock actuator is unlocked when “BD ULK” on CONSULT screen is touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT screen is
touched
Monitor Item
Condition
IGN ON SW
Indicates [On/Off] condition of ignition switch in ON position
KEY ON SW
Indicates [On/Off] condition of key switch
ACC ON SW
Indicates [On/Off] condition of ignition switch in ACC position
KEYLESS LOCK
Indicates [On/Off] condition of lock signal from keyfob
KEYLESS UNLOCK
Indicates [On/Off] condition of unlock signal from keyfob
KYLS TRNK/HAT
NOTE:
This item is displayed, but cannot be tested
DOOR SW-DR
Indicates [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicates [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicates [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicates [On/Off] condition of rear door switch LH
BACK DOOR SW
Indicates [On/Off] condition of back door switch
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be tested
CDL LOCK SW
Indicates [On/Off] condition of door lock and unlock switch
CDL UNLOCK SW
Indicates [On/Off] condition of door lock and unlock switch
KEYLESS PANIC
Indicates [On/Off] condition of PANIC button of keyfob
Test item
Description
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
FLASHER
This test is able to check flasher operation [LH/RH/Off]
HORN
This test is able to check horn operation
• On: Operate
Test item
Description
REMO CONT IN REGIST
Keyfob ID code can be registered
REMO CONT IN ERASUR
Keyfob ID code can be erased
Revision: 2013 October
2014 JUKE
DLK-192
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK)
INFOID:0000000009754121
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
REMO CONT IN CONFIR
It can be checked whether Intelligent Key ID code is registered or not in this mode
HORN CHIRP SET
Hazard and horn reminder function (horn operation) mode can be changed in this mode
• On: Operate
• Off: Non-operation
HAZARD LAMP SET
Hazard and horn reminder function (hazard operation) mode can be changed in this mode
• MODE1: Non-operation
• MODE2: Unlock operation only
• MODE3: Lock operation only
• MODE4: Lock and unlock operation
AUTO LOCK SET
Auto door lock time can be changed in this mode
• MODE 1: Non-operation
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minute
• MODE 5: 3 minute
• MODE 6: 4 minute
• MODE 7: 5 minute
PANIC ALARM SET
Panic alarm button pressing time on keyfob remote control button can be selected from the
following with this mode
• MODE1: 0.5 sec
• MODE2: Non-operation
• MODE3: 1.5 sec
TRUNK OPEN SET
NOTE:
This item is displayed, but cannot be tested
Test item
Description
Monitor Item
Contents
KEY ON SW
Indicates [On/Off] condition of key switch.
LOCK STATUS
NOTE:
This item is displayed, but cannot be monitored.
VEHICLE SPEED
Indicates [Km/h] condition of vehicle speed signal from combination meter.
IGN ON SW
Indicates [On/Off] condition of ignition switch.
TRNK OPNR SW
NOTE:
This item is displayed, but cannot be monitored.
KYLS TRNK/HAT
NOTE:
This item is displayed, but cannot be monitored.
Revision: 2013 October
2014 JUKE
BCM
DLK-193
< ECU DIAGNOSIS INFORMATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference
INFOID:0000000009754122
ECU
Reference
BCM
BCS-132, "DTC Inspection Priority Chart"
Revision: 2013 October
2014 JUKE
DLK-194
< WIRING DIAGRAM >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR & LOCK SYSTEM
WIRING DIAGRAM
DOOR & LOCK SYSTEM
Wiring Diagram
INFOID:0000000009754123
JRKWC1077GB
Revision: 2013 October
2014 JUKE
DOOR & LOCK SYSTEM
DLK-195
< WIRING DIAGRAM >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWC1078GB
Revision: 2013 October
2014 JUKE
DLK-196
< WIRING DIAGRAM >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR & LOCK SYSTEM
JRKWC9394GB
Revision: 2013 October
2014 JUKE
DOOR & LOCK SYSTEM
DLK-197
< WIRING DIAGRAM >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWC9395GB
Revision: 2013 October
2014 JUKE
DLK-198
< WIRING DIAGRAM >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR & LOCK SYSTEM
JRKWC9396GB
Revision: 2013 October
2014 JUKE
DOOR & LOCK SYSTEM
DLK-199
< WIRING DIAGRAM >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWC9397GB
Revision: 2013 October
2014 JUKE
DLK-200
< WIRING DIAGRAM >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR & LOCK SYSTEM
JRKWC9398GB
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст