Nissan Juke (2014 year). Service Repair Manual — part 59
FUEL FILLER LID OPENER
DLK-169
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000009754089
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000009754090
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove fuel mounting pin (1).
3.
Remove mounting screws, and then remove fuel filler lid.
INSTALLATION
Note the following items, and install in the reverse order of removal.
1.
Fuel filler lid opener cable
2.
Cable protector
3.
Fuel filler lid lock assembly
4.
Fuel filler lid assembly
5.
Spring
6.
Bumper rubber
: Clip
: Do not reuse
JMKIA5904ZZ
JMKIA5717ZZ
Revision: 2013 October
2014 JUKE
DLK-170
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FUEL FILLER LID OPENER
CAUTION:
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply the touch-up paint (the body color) onto the head of the mounting screws.
NOTE:
• The following table shows the specifide values for checking nomal installation status.
• Fitting adjustment cannot be perfomed.
Unit: mm (in)
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000009754091
REMOVAL
1.
Remove hood lock control cable assembly from instrument lower panel (LH). Refer to
LOCK CONTROL CABLE : Removal and Installation"
.
2.
Remove fuel filler lid opener cable (2) from fuel filler lid opener
lever (1).
3.
Remove front kicking plate inner (LH) and rear kicking plate inner (LH and RH). Refer to
ING PLATE INNER : Removal and Installation"
.
4.
Remove dash side finisher (LH). Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installation"
5.
Remove center pillar lower garnish (LH). Refer to
INT-22, "CENTER PILLAR LOWER GARNISH :
.
6.
Remove luggage side lower finisher (RH). Refer to
INT-35, "LUGGAGE SIDE LOWER FINISHER :
.
7.
Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to
LOCK : Removal and Installation"
.
8.
Disengage each harness protector (1), and then remove fuel
filler lid opener cable (2).
9.
Remove fuel filler lid opener cable fixing clips, and then remove fuel filler lid opener cable.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
FUEL FILLER LID LOCK
Clearance
Evenness
Fuel filler lid – Body side outer
2.0 – 4.0 (0.079 – 0.157)
(-1.0) – (+1.0) [(-0.039) – (+0.039)]
JMKIA5901ZZ
JMKIA5720ZZ
Revision: 2013 October
2014 JUKE
FUEL FILLER LID OPENER
DLK-171
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000009754092
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove luggage side lower finisher (RH). Refer to
INT-35, "LUGGAGE SIDE LOWER FINISHER :
.
3.
Rotate and disengage fuel filler lid lock assembly, and then
remove fuel filler lid lock assembly.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.
4.
Disengage fuel filler lid opener cable (1). Remove fuel filler lid
opener cable while pressing stopper pin (2).
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
JMKIA5718ZZ
JMKIA5719ZZ
Revision: 2013 October
2014 JUKE
DLK-172
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
DOOR SWITCH
DOOR SWITCH
Exploded View
INFOID:0000000009754093
Removal and Installation
INFOID:0000000009754094
REMOVAL
Remove the TORX bolt (A), and then remove door switch (1).
INSTALLATION
Install in the reverse order of removal.
1.
Door switch
2.
TORX bolt
JMKIA2569GB
JMKIA2173ZZ
Revision: 2013 October
2014 JUKE
INSIDE KEY ANTENNA
DLK-173
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSIDE KEY ANTENNA
INSTRUMENT CENTER
INSTRUMENT CENTER : Removal and Installation
INFOID:0000000009754095
REMOVAL
1.
Remove the multi display unit. Refer to
AV-183, "Removal and Installation"
2.
Remove the inside key antenna (instrument center) (1) mount-
ing clip (A), and then remove inside key antenna (instrument
center).
CAUTION:
Be careful not to drop mounting clip (A) into instrument
panel.
INSTALLATION
Install in the reverse order of removal.
CONSOLE
CONSOLE : Removal and Installation
INFOID:0000000009754096
REMOVAL
1.
Remove the center console assembly. Refer to
IP-24, "Removal and Installation"
2.
Remove the inside key antenna (console) (1) mounting clip (A),
and then remove inside key antenna (console).
INSTALLATION
Install in the reverse order of removal.
LUGGAGE ROOM
JMKIA5573ZZ
JMKIA5575ZZ
Revision: 2013 October
2014 JUKE
DLK-174
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
INSIDE KEY ANTENNA
LUGGAGE ROOM : Exploded View
INFOID:0000000009754097
LUGGAGE ROOM : Removal and Installation
INFOID:0000000009754098
REMOVAL
1.
Remove the luggage floor finisher. Refer to
.
2.
Remove the inside key antenna (luggage room) (1) mounting
clip RH (A).
3.
Disengage inside key antenna (luggage room) fixing clip using a
flat-bladed screwdriver (A), and then pull out forward the inside
key antenna (luggage room).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Visually check the clips for deformation and damage during installation.
Replace with new ones if necessary.
1.
Inside key antenna (luggage room)
2.
Clip
: Do not reuse
JMKIA5576ZZ
JMKIA5577ZZ
JMKIA5578ZZ
Revision: 2013 October
2014 JUKE
OUTSIDE KEY ANTENNA
DLK-175
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE KEY ANTENNA
DRIVER SIDE
DRIVER SIDE : Removal and Installation
INFOID:0000000009754099
REMOVAL
Remove the driver side outside handle. Refer to
DLK-161, "OUTSIDE HANDLE : Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
PASSENGER SIDE
PASSENGER SIDE : Removal and Installation
INFOID:0000000009754100
REMOVAL
Remove the passenger side outside handle. Refer to
DLK-161, "OUTSIDE HANDLE : Removal and Installa-
.
INSTALLATION
Install in the reverse order of removal.
REAR BUMPER
REAR BUMPER : Removal and Installation
INFOID:0000000009754101
REMOVAL
1.
Remove the rear bumper fascia. Refer to
EXT-20, "Removal and Installation"
2.
Remove the outside key antenna (rear bumper) (1) mounting
clip (A), then remove outside key antenna (rear bumper).
INSTALLATION
Install in the reverse order of removal.
JMKIA5580ZZ
Revision: 2013 October
2014 JUKE
DLK-176
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Removal and Installation
INFOID:0000000009754102
REMOVAL
1.
Remove the Intelligent Key warning buzzer (1) mounting bolt
(A), and then remove the Intelligent Key warning buzzer.
INSTALLATION
Install in the reverse order of removal.
JMKIA5571ZZ
Revision: 2013 October
2014 JUKE
REMOTE KEYLESS ENTRY RECEIVER
DLK-177
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Removal and Installation
INFOID:0000000009754103
REMOVAL
1.
Remove the glove box assembly. Refer to
IP-13, "Removal and Installation"
2.
Remove the remote keyless entry receiver (1) mounting bolt (A),
and then remove remote keyless entry receiver.
INSTALLATION
Install in the reverse order of removal.
JMKIA6084ZZ
Revision: 2013 October
2014 JUKE
DLK-178
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY BATTERY
INTELLIGENT KEY BATTERY
Removal and Installation
INFOID:0000000009754104
1.
Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2.
Insert a remover tool (A) wrapped with a cloth into the slit of the
corner and twist it to separate the upper part from the lower part.
CAUTION:
• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3.
Replace the battery with new one.
4.
Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:
• When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
• After replacing the battery, check that all Intelligent Key
functions work normally.
PIIB6221E
Battery replacement
:Coin-type lithium battery
(CR2025)
PIIB6222E
Revision: 2013 October
2014 JUKE
PRECAUTIONS
DLK-179
< PRECAUTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009754105
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009754106
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
PIIB3706J
Revision: 2013 October
2014 JUKE
DLK-180
< PRECAUTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
PRECAUTIONS
Precautions for Removing of Battery Terminal
INFOID:0000000010288672
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Work
INFOID:0000000009754107
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operational.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
SEF289H
Revision: 2013 October
2014 JUKE
PREPARATION
DLK-181
< PREPARATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009754108
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009754109
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locating the noise
(J-50397)
NISSAN Squeak and Rat-
tle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locating the noise
Remover tool
Remove the clips, pawls, and metal clips
Power tool
SIIA0995E
PIIB7923J
PIIB1407E
Revision: 2013 October
2014 JUKE
DLK-182
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009754110
Component Description
INFOID:0000000009754111
1.
IPDM E/R
Refer to
2.
TCM
Refer to
SYSTEM : Component Parts Loca-
tion"
3.
Combination meter
4.
Key switch
5.
BCM
Refer to
SYSTEM : Component Parts Loca-
tion"
6.
Power window main switch
(door lock/unlock switch)
7.
Front door switch (driver side)
8.
Front door lock assembly (driver
side)
9.
Back door opener assembly
10. Back door opener switch
11.
Remote keyless entry receiver
A.
View with the glove box assembly re-
moved
JMKIA6160ZZ
Item
Function
Back door opener actuator
Opens the back door with the back door open signal from BCM.
Back door opener switch
Inputs back door opener switch operation signal to BCM.
BCM
Controls the door lock system.
Revision: 2013 October
2014 JUKE
COMPONENT PARTS
DLK-183
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Combination meter
• Performs operation method guide and warning with buzzer.
• Transmits vehicle seep signal to CAN communication line.
Door lock actuator
• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.
Door lock and unlock switch
Transmits door lock/unlock operation to BCM.
Door switch
Detects door open/close condition.
IPDM E/R
Sounds horn via CAN communication between BCM.
Keyfob
Transmits button operation to remote keyless entry receiver.
Key switch
Key switch detects that ignition key is inserted into the ignition key cylinder, and
then transmits the signal to BCM.
Remote keyless entry receiver
Receives keyfob operation and transmits to BCM.
TCM
Transmits shift position signal to BCM via CAN communication line.
Item
Function
Revision: 2013 October
2014 JUKE
DLK-184
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
POWER DOOR LOCK SYSTEM
POWER DOOR LOCK SYSTEM
System Diagram
INFOID:0000000009754112
System Description
INFOID:0000000009754113
DOOR LOCK FUNCTION
• The door lock and unlock switch (driver side) is build into power window main switch.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors and
are unlocked.
Door Key Cylinder
• With the door key inserted in the door key cylinder on driver side, turning it to “LOCK”, will lock door lock
actuator of all doors.
• With the door key inserted in the door key cylinder on driver side, turning it to “UNLOCK” once unlocks the
driver side door lock actuator; turning it to “UNLOCK” again within 5 seconds after the first unlock operation
unlocks all of the other doors. (SELECTIVE UNLOCK OPERATION)
KEY REMINDER FUNCTION
When door lock and unlock switch are operated while key is inserted into key switch and any door is open,
door locks once but immediately unlocks. This operation prevents keyfob from being left in the vehicle.
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (LOCK OPERATION)
The interlock door lock function is the function that locks all doors linked with the vehicle speed or shift posi-
tion. It has 2 types as follows.
Vehicle Speed Sensing Auto Door Lock
All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 24 km/h (15 MPH) or more.
P Range Interlock Door Lock*
All doors are locked when shifting the selector lever from the P position to any position other than P.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is in the ON posi-
tion and the shift signal received from the TCM via CAN communication is shifted from the P position to any
position other than P.
Setting change of Automatic Door Lock/Unlock Function
The lock operation setting of the automatic door lock/unlock function can be changed.
With CONSULT
The ON/OFF switching of the automatic door lock function and the type selection of the automatic door lock/
unlock function can be performed at the WORK SUPPORT setting of CONSULT.
Without CONSULT
JMKIA6161GB
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст