Juke F15 (2012 year). Service Repair Manual — part 261

IP-14

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

[ ]: Number indicates step in removal procedure.

WARNING:

Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.

REMOVAL

CAUTION:

When removing, always use a remover tool that is made of plastic.

Remove shift lever knob (MT models only).
• 5MT models: Refer to

TM-25, "Removal and Installation"

• 6MT models: Refer to

TM-78, "Removal and Installation"

Remove console finisher assembly.
1.

Put selector lever in “N” position.

Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to

PB-

2, "Inspection and Adjustment"

Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.

Remove console finisher assembly while pulling it towards vehicle rear.

A/C control fixing screws (with manual A/C)

[21]

Cluster lid C

[22]

[2]

AV C/U

[23]

[3]

Harness connector of hazard switch

[24]

Cluster tray

[25]

Front body side welt RH

[26]

Front pillar garnish RH

[27]

Instrument side finisher RH

[28]

Instrument under cover RH

[29]

Glove box lid

[30]

Glove box assembly

[31]

Passenger air bag module

[32]

Switch panel

[33]

Instrument panel assembly mounting bolts and screws

[34]

Instrument panel assembly

[35]

INSTRUMENT PANEL ASSEMBLY

IP-15

< REMOVAL AND INSTALLATION >

CAUTION:

• Be careful not for damaging parts in surrounding area.
• Remove metal clips slowly so that they are not damaged.

Disconnect seat heated switch harness connectors (with seat heated switch).

Remove console rear finisher.
1.

Put front seat assembly (LH and RH) to frontmost position.

Pull back console rear finisher, and disengage the pawls
and metal clips.

Remove center console assembly fixing screws (A).

Remove instrument lower cover LH.
1.

Put front seat assembly LH to rearmost position.

: Metal clip

JMJIA4550ZZ

: Pawl

: Metal clip

JMJIA4183ZZ

JMJIA4202ZZ

IP-16

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

Remove fixing clip (A).

Pull the instrument lower cover LH crosswise, and disen-
gage the pawl and metal clips.

CAUTION:

Remove pawl and metal clips slowly so that they are not
damaged.

Remove instrument lower cover RH.
1.

Put front seat assembly RH to rearmost position.

Remove fixing clip (A).

Pull the instrument lower cover RH crosswise, and disen-
gage the pawl and metal clips.

CAUTION:

Remove pawl and metal clips slowly so that they are not
damaged.

Remove center console assembly.
1.

Remove center console fixing screws (A).

Remove seat heated switch harness clip (with seat heated switch).

Lift up center console assembly back side.

CAUTION:

Be careful not for damaging parts in surrounding area.

Release front pillar portion of front body side welt LH. Refer to

INT-20, "BODY SIDE WELT : Removal and

Installation"

Remove front pillar garnish LH. Refer to

INT-18, "FRONT PILLAR GARNISH : Removal and Installation"

10. Remove instrument side finisher LH.

Insert remover tool (A) between instrument side finisher LH
and instrument panel assembly to disengage the pawls as
shown in the figure.

Pull back instrument side finisher LH.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-
age.

11. Remove instrument under cover LH.

: Pawl

: Metal clip

JMJIA4551ZZ

: Pawl

: Metal clip

JMJIA4552ZZ

JMJIA4553ZZ

: Pawl

JMJIA4554ZZ

INSTRUMENT PANEL ASSEMBLY

IP-17

< REMOVAL AND INSTALLATION >

Remove fixing clips (A).

Pull downward and disengage pawls.

NOTE:
RHD models
1.

Remove fixing clips (A).

Remove fixing clip (B).

Pull downward and disengage pawls.

12. Remove instrument lower panel LH.

Remove hood opener and fuel lid opener lever. Refer to

DLK-173, "HOOD LOCK CONTROL CABLE

: Removal and Installation"

Remove fixing screw (A).

Pull back instrument lower panel LH, and then disengage
the pawls and metal clips.

Disconnect harness connectors and aspirator duct.

13. Remove driver air bag module. Refer to

SR-13, "Removal and Installation"

14. Remove steering wheel. Refer to

ST-9, "Removal and Installation"

15. Remove steering column covers.

Place the tilt to the lowest level.

Remove steering lock escutcheon (1). (without Intelligent
Key)

Remove fixing screws (A).

Pull up steering column upper cover (2), and then disen-
gage steering column upper cove fixing pawls.

Remove steering column upper cover.

Pull down the steering column lower cover (3), and then
remove steering column lower cover.

NOTE:
Disengage the pawls, and then remove steering lock escutch-
eon (4). (with Intelligent Key)

: Pawl

JMJIA4555ZZ

: Pawl

JMJIA4585ZZ

: Pawl

: Metal clip

JMJIA4556ZZ

: Pawl

JMJIA4189ZZ

IP-18

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

16. Remove spiral cable. Refer to

SR-16, "Removal and Installation"

17. Remove combination switch. Refer to

BCS-94, "Removal and Installation"

18. Remove cluster lid A.

Cover steering shaft with a shop cloth (A) to prevent dam-
age.

Pull back cluster lid A while holding the lower side and dis-
engage the metal clips underside.

Hold both upper sides of cluster lid A and pull it out towards
vehicle rear, and disengage pawl and metal clips topside.

Disconnect push-button ignition switch harness connector
and NATS antenna amp.harness connector. (with Intelligent
Key)

CAUTION:

Remove metal clips slowly so that they are not damaged.

19. Remove combination meter. Refer to

MWI-69, "Removal and Installation"

20. Remove multi display unit (with auto A/C) or A/C finisher (with manual A/C).

• Multi display unit (with auto A/C)
- Insert a remover tool (A) between multi display unit (1) and instrument panel assembly (2), and then dis-

engage pawls and metal clip.

- Pull back multi display unit, and then disconnect harness connector.

CAUTION:

Apply protective tape (B) on the part to protect it from damage.

• A/C finisher (with manual A/C)
- Remove intake door lever knob (3). Refer to

HAC-239, "Removal and Installation"

- Insert a remover tool (A) between A/C finisher (4) and instrument panel assembly (5), and then disen-

gage pawls and metal clip.

- Pull back A/C finisher.

CAUTION:

Apply protective tape (B) on the part to protect it from damage.

21. Remove A/C control fixing screws (with Manual A/C). Refer to

HAC-239, "Removal and Installation"

: Pawl

: Metal clip

JMJIA4557ZZ

Multi display unit (with auto A/C)

A/C finisher (with manual A/C)

: Pawl

: Metal clip

JMJIA4558ZZ

INSTRUMENT PANEL ASSEMBLY

IP-19

< REMOVAL AND INSTALLATION >

22. Remove cluster lid C.

Remove fixing screws (A).

Pull back cluster lid C, and disengage the pawls and metal
clips.

Disconnect harness connector.

23. Remove audio or NAVI control unit.

• Audio unit: Refer to

AV-38, "Removal and Installation"

• NAVI control unit: Refer to

AV-84, "Removal and Installation"

24. Disconnect hazard switch harness connector.

25. Remove cluster tray.

Insert a remover tool (A) between cluster tray and instru-
ment panel assembly, and then pull downward and disen-
gage metal clips.

Pull back cluster tray.

Disconnect harness connectors.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-
age.

26. Release front pillar portion of front body side welt RH. Refer to

INT-20, "BODY SIDE WELT : Removal and

Installation"

27. Remove front pillar garnish RH. Refer to

INT-18, "FRONT PILLAR GARNISH : Removal and Installation"

28. Remove instrument side finisher RH.

Insert remover tool (A) between instrument side finisher RH
and instrument panel assembly to disengage the pawls as
shown in the figure.

Pull back instrument side finisher RH.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-
age.

29. Remove instrument under cover RH.

Remove fixing clips (A).

Pull downward and disengage pawl and metal clips.

30. Remove glove box lid.

: Pawl

: Metal clip

JMJIA4559ZZ

: Metal clip

JMJIA4560ZZ

: Pawl

JMJIA4561ZZ

: Pawl

: Metal clip

JMJIA4562ZZ

IP-20

< REMOVAL AND INSTALLATION >

INSTRUMENT PANEL ASSEMBLY

Open glove box lid.

Pull glove box lid (1) toward vehicle rear, and then disen-
gage the joint from instrument panel assembly (2).

Disengage the pawl, and then remove damper pin on right
side.

CAUTION:

Never excessively pull string of glove box damper.

31. Remove glove box assembly.

Remove fixing screws (A).

Pull back the glove box cover assembly while holding the lower side and disengage the pawls.

32. Remove front passenger air bag module. Refer to

SR-19, "Removal and Installation"

33. Remove switch panel.

Insert remover tool (A) between switch panel and instru-
ment panel assembly to disengage the pawls as shown in
the figure.

Pull up switch panel, and then disconnect harness connec-
tor.

CAUTION:

Apply protective tape (B) on the part to protect it from dam-
age.

JMJIA4563ZZ

: Pawl

JMJIA4564ZZ

2WD models

4WD models

: Pawl

JMJIA4565ZZ

: Pawl

JMJIA4566ZZ

INSTRUMENT PANEL ASSEMBLY

IP-21

< REMOVAL AND INSTALLATION >

34. Remove instrument panel assembly mounting screws (A) and bolts (B).

CAUTION:

Cover tool with a shop cloth to prevent windshield glass from being damaged.

35. Remove instrument panel assembly.

Disengage harness (A) and harness (B) of front pillar LH and RH portions from instrument panel
assembly.

Remove instrument panel from passenger door opening portion.

CAUTION:

• Cover CVT shift selector upper surface with a shop cloth to prevent it from being damaged.
• When removing instrument panel assembly, 2 workers are required to prevent it from drop-

ping.

36. Remove the following parts after removing instrument panel assembly.

• Side defrostor nozzle: Refer to

VTL-10, "SIDE DEFROSTER NOZZLE : Removal and Installation"

• Side ventilator grille: Refer to

VTL-11, "SIDE VENTILATOR GRILLE : Removal and Installation"

• Side defrostor grille:

VTL-11, "SIDE DEFROSTER GRILLE : Removal and Installation"

• Front defrostor nozzle:

VTL-11, "FRONT DEFROSTER NOZZLE : Removal and Installation"

• Center ventilator duct:

VTL-12, "CENTER VENTILATOR DUCT : Removal and Installation"

• Side ventilator duct:

VTL-12, "SIDE VENTILATOR DUCT : Removal and Installation"

• GPS antenna:

AV-89, "Removal and Installation"

• Hazard switch:

EXL-97, "Removal and Installation"

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

After installation, adjust the parking brake lever stroke. Refer to

PB-2, "Inspection and Adjustment"

JMJIA4567ZZ

JMJIA4568ZZ

IP-22

< REMOVAL AND INSTALLATION >

CENTER CONSOLE ASSEMBLY

CENTER CONSOLE ASSEMBLY

Exploded View

INFOID:0000000006275834

CVT models

JMJIA4498ZZ

Console indicator finisher

Instrument lower cover RH

Center console assembly

Instrument lower cover LH

Instrument stay

CVT shift selector assembly

Console rear bracket

Console rear finisher

Seat heated switch

10. Console switch finisher

11.

Console switch finisher

12. Console finisher assembly

13. Console mask

14. Console front bracket

: Pawl

: Metal clip

CENTER CONSOLE ASSEMBLY

IP-23

< REMOVAL AND INSTALLATION >

MT models

Removal and Installation

INFOID:0000000006342267

WARNING:

Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or
more.

REMOVAL

CAUTION:

When removing, always use a remover tool that is made of plastic.

JMJIA4497ZZ

Console boot

Instrument lower cover RH

Center console assembly

Instrument lower cover LH

Instrument stay

Console center bracket

Console rear bracket

Console rear finisher

Seat heated switch

10. Console switch finisher

11.

Console switch finisher

12. Console finisher assembly

13. Console mask

14. Console front bracket

: Pawl

: Metal clip

IP-24

< REMOVAL AND INSTALLATION >

CENTER CONSOLE ASSEMBLY

Remove shift lever knob (MT models only).
• 5MT models: Refer to

TM-25, "Removal and Installation"

• 6MT models: Refer to

TM-78, "Removal and Installation"

Remove console finisher assembly.
1.

Put selector lever in “N” position.

Loosen the parking brake lever stroke by turning the adjusting nut with a socket wrench. Refer to

PB-

2, "Inspection and Adjustment"

Lift up console finisher assembly in numerical order shown in the figure and disengage metal clips.

Remove console finisher assembly while pulling it towards vehicle rear.

CAUTION:

• Be careful not for damaging parts in surrounding area.
• Remove metal clips slowly so that they are not damaged.

Remove console rear finisher.
1.

Put front seat assembly (LH and RH) to frontmost position.

Pull back console rear finisher, and disengage the pawls
and metal clips.

: Metal clip

JMJIA4550ZZ

: Pawl

: Metal clip

JMJIA4183ZZ

CENTER CONSOLE ASSEMBLY

IP-25

< REMOVAL AND INSTALLATION >

Remove center console assembly fixing screws (A).

Remove instrument lower cover LH.
1.

Put front seat assembly LH to rearmost position.

Remove fixing clip (A).

Pull the instrument lower cover LH crosswise, and disen-
gage the pawl and metal clips.

CAUTION:

Remove pawl and metal clips slowly so that they are not
damaged.

Remove instrument lower cover RH.
1.

Put front seat assembly RH to rearmost position.

Remove fixing clip (A).

Pull the instrument lower cover RH crosswise, and disen-
gage the pawl and metal clips.

CAUTION:

Remove pawl and metal clips slowly so that they are not
damaged.

Remove center console assembly.

Remove center console fixing screws (A).

Lift up center console assembly back side.

CAUTION:

Be careful not for damaging parts in surrounding area.

INSTALLATION

Note the following item, and then install in the reverse order of removal.

CAUTION:

After installation, adjust the parking brake lever stroke. Refer to

PB-2, "Inspection and Adjustment"

JMJIA4202ZZ

: Pawl

: Metal clip

JMJIA4551ZZ

: Pawl

: Metal clip

JMJIA4552ZZ

JMJIA4553ZZ

IP-26

< REMOVAL AND INSTALLATION >

CENTER CONSOLE ASSEMBLY

Disassembly and Assembly

INFOID:0000000006275836

Disassembly and Assembly of Console Finisher Assembly

CAUTION:

When disassembling, always use a remover tool that is made of plastic.

DISASSEMBLY

Remove console finisher assembly. Refer to

IP-23, "Removal and Installation"

Remove console indicator finisher (CVT models)
Disengage connection of the console indicator finisher (2) fixing
pawls from the inside of the console finisher assembly (1)
toward the outside, and remove.

Remove console indicator finisher (MT models)
Disengage connection of the console boot (2) fixing pawls from
the inside of the console finisher assembly (1) toward the out-
side, and remove.

Remove console switch finisher.
Disengage connection of the console switch finisher (2) fixing
pawls from the inside of the console finisher assembly (1)
toward the outside, and remove.
NOTE:
Remove seat heated switch. Refer to

SE-51, "Removal and

Installation"

ASSEMBLY

Assemble in the reverse order of disassembly.

: Pawl

JMJIA4204ZZ

: Pawl

JMJIA4573ZZ

: Pawl

JMJIA4574ZZ

LAN

LAN-1