Juke F15 (2012 year). Service Repair Manual — part 259
INT-18
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
BODY SIDE TRIM
Exploded View
INFOID:0000000006418517
FRONT PILLAR GARNISH
FRONT PILLAR GARNISH : Removal and Installation
INFOID:0000000006418518
REMOVAL
CAUTION:
1.
Rear body side welt
2.
Center pillar upper garnish
3.
Front body side welt
4.
Front pillar garnish
5.
Metal clip
6.
Dash side finisher
7.
Harness clip
8.
Front kicking plate inner
9.
Center pillar lower garnish
10. Rear kicking plate inner
: Clip
: Pawl
: Metal clip
: Vehicle front
: Do not reuse
JMJIA4527ZZ
BODY SIDE TRIM
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1.
Release front pillar garnish portion of front body side welt.
2.
Remove front pillar garnish.
1.
Disengage front pillar garnish fixing clips with a remover tool
(A).
2.
Twist clip portion of front pillar garnish using long nose pliers
while pulling upper side of front pillar garnish toward inside,
and then remove clip from front pillar garnish side.
3.
Remove front pillar garnish of pull toward the arrow direc-
tion.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing front pillar garnish, check that clips are securely in body panel holes, and press
them in.
• Replace front pillar garnish with a new part after removal. Never reuse front pillar garnish.
KICKING PLATE INNER
KICKING PLATE INNER : Removal and Installation
INFOID:0000000006418519
REMOVAL
CAUTION:
Never damage the body.
FRONT KICKING PLATE INNER
Pull up front kicking plate inner, and then disengage the pawls.
REAR KICKING PLATE INNER
Pull up rear kicking plate inner, and then disengage the pawls.
INSATALLATION
Install in the reverse order of removal.
DASH SIDE FINISHER
: Clip
JMJIA4528ZZ
: Pawl
JMJIA4387ZZ
: Pawl
JMJIA4388ZZ
INT-20
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000006418520
REMOVAL
CAUTION:
Never damage the body.
1.
Remove front kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and Installation"
2.
Pull back dash side finisher, and then disengage the pawls.
3.
Disconnect dash side finisher, vehicle front side, from stud bolt and remove dash side finisher.
INSTALLATION
Install in the reverse order of removal.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000006418521
REMOVAL
CAUTION:
• Never excessively pull body side welt.
• Never damage the body.
FRONT BODY SIDE WELT
1.
Remove front kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and Installation"
2.
Remove front body side welt.
REAR BODY SIDE WELT
1.
Remove rear kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and Installation"
.
2.
Remove rear body side welt.
INSTALLATION
Install in the reverse order of removal.
CENTER PILLAR LOWER GARNISH
CENTER PILLAR LOWER GARNISH : Removal and Installation
INFOID:0000000006418522
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1.
Fully open front door and rear door.
2.
Slide front seat to the fully forward position. Tilt seatback forward.
3.
Remove Front body side welt and rear body side welt. Refer to
INT-20, "BODY SIDE WELT : Removal
: Pawl
JMJIA4529ZZ
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
4.
Disengage center pillar lower garnish fixing clips and pawls with
a remover tool (A), and then remove center pillar lower garnish.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing center pillar lower garnish, check that clips are securely in body panel holes, and
press them in.
CENTER PILLAR UPPER GARNISH
CENTER PILLAR UPPER GARNISH : Removal and Installation
INFOID:0000000006418523
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1.
Remove center pillar lower garnish. Refer to
INT-20, "CENTER PILLAR LOWER GARNISH : Removal
2.
Remove front seat belt shoulder anchor. Refer to
SB-5, "SEAT BELT RETRACTOR : Removal and Instal-
.
3.
Disengage center pillar upper garnish lower side fixing pawl.
4.
Disengage center pillar upper garnish upper side fixing clip.
NOTE:
Removal operation can be performed easily when pressing pawl by inserting a removal tool from direction
(A) as shown in the figure.
CAUTION:
Be careful not to apply excessive force when removing center pillar upper garnish. Otherwise,
pawl may be damaged and fragments may drop in panel holes on body.
INATALLATION
: Clip
: Pawl
JMJIA4390ZZ
: Pawl
JMJIA4391ZZ
PIIB7674J
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace center pillar upper garnish with a new part after removal. Never reuse center pillar upper
garnish.
• When installing center pillar upper garnish, check that pawls are securely in body panel holes, and
press them in.
FLOOR TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Exploded View
INFOID:0000000006418524
LHD models
Removal and Installation
INFOID:0000000006418525
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1.
Remove front seat assembly (LH and RH).
• 2WD models: Refer to
SE-19, "Removal and Installation"
• 4WD models: Refer to
SE-27, "Removal and Installation"
2.
Remove rear seat cushion.
• 2WD models: Refer to
SE-33, "SEAT CUSHION : Removal and Installation"
.
JMJIA4530ZZ
1.
Floor carpet
2.
Carpet hook
3.
Trim clip
4.
Column hole cover
5.
Harness clip
6.
Front floor spacer RH
7.
Front floor spacer LH
8.
Rear floor spacer LH
9.
Rear floor spacer RH
: Clip
: Pawl
INT-24
< REMOVAL AND INSTALLATION >
FLOOR TRIM
• 4WD models: Refer to
SE-42, "SEAT CUSHION : Removal and Installation"
.
3.
Remove center console assembly. Refer to
IP-23, "Removal and Installation"
4.
Remove instrument stay.
Remove instrument stay mounting nuts (A), and then remove
instrument stay.
5.
Disconnect drain hose.
• HR16DE: Refer to
HA-53, "A/C UNIT ASSEMBLY : Removal and Installation"
• MR16DDT: Refer to
HA-113, "A/C UNIT ASSEMBLY : Removal and Installation"
6.
Remove foot ducts (LH and RH).
VTL-13, "REAR HEATER DUCT 2 : Removal and Installation"
with foot ducts).
7.
Remove sift selector assembly.
• 5MT models: Refer to
TM-25, "Removal and Installation"
.
• 6MT models: Refer to
TM-78, "Removal and Installation"
.
• CVT models (RE0F10B): Refer to
TM-270, "Removal and Installation"
• CVT models (RE0F11A): Refer to
TM-481, "Removal and Installation"
.
8.
Remove diagnosis sensor unit. Refer to
SR-30, "Removal and Installation"
.
9.
Remove parking brake lever. Refer to
PB-5, "Removal and Installation"
10. Remove the inside key antenna (console lower).Refer to
DLK-188, "INSTRUMENT CENTER : Removal
(Models with Intelligent Key system).
11. Remove center pillar lower garnish (LH and RH). Refer to
INT-20, "CENTER PILLAR LOWER GARNISH :
.
12. Remove column hole cover.
Disengage trim clips (A), and then remove column hole cover.
13. Remove dash side finisher (LH and RH). Refer to
INT-20, "DASH SIDE FINISHER : Removal and Installa-
14. Disengage pawl using a remover tool (A) and open the harness
clip.
: Vehicle front
JMJIA4531ZZ
JMJIA4532ZZ
: Pawl
JMJIA4396ZZ
FLOOR TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
15. Remove floor carpet.
NOTE:
Disengage pawls using a remover tool and remove carpet hook.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Replace diagnosis sensor unit fixing bolts with a new part after removal. Never reuse diagnosis sen-
sor unit fixing bolts.
: Pawl
JMJIA3620ZZ
INT-26
< REMOVAL AND INSTALLATION >
HEADLINING
HEADLINING
Exploded View
INFOID:0000000006418526
LHD models
Removal and Installation
INFOID:0000000006418527
REMOVAL
CAUTION:
JMJIA4533ZZ
1.
Headlining assembly
2.
Assist grip clip
3.
Rear assist grip RH
4.
Front assist grip RH
5.
Sun visor assembly RH
6.
Sun visor cover RH
7.
Sun visor cover LH
8.
Sun visor assembly LH
9.
Rear assist grip LH
10. Headlining clip
11.
Sun visor holder RH
12. Map lamp
13. Sun visor holder LH
14. Metal clip
: Clip
: Pawl
HEADLINING
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1.
Remove front pillar garnish (LH and RH). Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and
.
2.
Disconnect harness connector (A) from headlining and harness
clips.
3.
Remove center pillar upper garnish (LH and RH). Refer to
INT-21, "CENTER PILLAR UPPER GARNISH :
.
4.
Remove back door weather-strip.
• TYPE1: Refer to
DLK-170, "BACK DOOR WEATHER-STRIP : Removal and Installation"
.
• TYPE2: Refer to
DLK-333, "BACK DOOR WEATHER-STRIP : Removal and Installation"
.
• TYPE3: Refer to
DLK-468, "BACK DOOR WEATHER-STRIP : Removal and Installation"
.
• TYPE4: Refer to
DLK-584, "BACK DOOR WEATHER-STRIP : Removal and Installation"
.
5.
Remove luggage side upper finisher (LH and RH).
INT-32, "LUGGAGE SIDE UPPER FINISHER :
.
6.
Remove all assist grips.
1.
Disengage pawl of assist grip clip (1) using a remover tool
(A). Slide assist grip clip forward and remove it.
2.
Slide assist grip (2) forward and remove it.
3.
Remove metal clips.
7.
Remove sun visor assembly (LH and RH).
1.
Disengage sun visor cover fixing pawls with a remover tool
(A), and then remove sun visor cover.
2.
Remove sun visor assembly fixing screw, and then remove sun visor assembly.
8.
Remove inside mirror and inside mirror cover. Refer to
MIR-41, "Removal and Installation"
.
9.
Remove map lamp assembly. Refer to
INL-37, "Removal and Installation"
10. Remove front seat assembly (passenger).
• 2WD models: Refer to
SE-19, "Removal and Installation"
: Clip
JMJIA4534ZZ
: Pawl
JMJIA4398ZZ
: Pawl
JMJIA4399ZZ
INT-28
< REMOVAL AND INSTALLATION >
HEADLINING
• 4WD models: Refer to
SE-27, "Removal and Installation"
11. Remove sun visor holder (LH and RH).
Rotate 90
°
. Remove toward vehicle lower.
12. Remove headlining clips.
13. Remove headlining assembly through the back door.
CAUTION:
• Two workers are required for removal in order to prevent
damage.
• Apply protective tape to the portion where contact may
occur during work.
• Never bend headlining when removing.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing headlining, start by installing both sun visor holders and headlining clips in order to
keep the headlining in position.
• Never bend headlining when installing.
• Be careful that the surface is not wrinkled when installing.
JMJIA4401ZZ
JMJIA4402ZZ
LUGGAGE FLOOR TRIM
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
LUGGAGE FLOOR TRIM
Exploded View
INFOID:0000000006418528
2WD models
JMJIA4535ZZ
1.
Rear pillar cap RH
2.
Luggage side upper finisher RH
3.
Luggage side lower finisher RH
4.
Luggage floor board
5.
Luggage side upper finisher LH
6.
Rear pillar cap LH
7.
Luggage side lower finisher LH
8.
Seat belt hook LH
9.
Shock absorber mask LH
10. Luggage side lower finisher grille LH 11.
Repair kit holder
(Models without spare tire)
12. Luggage rear plate
13. Luggage side lower finisher grille RH 14. Luggage room lamp
15. Shock absorber mask RH
16. Seat belt hook RH
17. Luggage floor box
18. Luggage floor rear center spacer
(Models with spare tire)
19. Spare tire clamp
(Models with spare tire)
: Clip
: Pawl
INT-30
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
4WD models
LUGGAGE REAR PLATE
LUGGAGE REAR PLATE : Removal and Installation
INFOID:0000000006418529
CAUTION:
• When removing, always use a remover tool that is made of plastic.
: Metal clip
: Vehicle front
JMJIA4536ZZ
1.
Rear pillar cap RH
2.
Luggage side upper finisher RH
3.
Luggage side lower finisher RH
4.
Luggage floor board
5.
Luggage side upper finisher LH
6.
Rear pillar cap LH
7.
Luggage side lower finisher LH
8.
Seat belt hook LH
9.
Shock absorber mask LH
10. Luggage side lower finisher grille LH 11.
Luggage floor rear spacer LH
12. Luggage rear plate
13. Luggage side lower finisher grille RH 14. Luggage room lamp
15. Shock absorber mask RH
16. Seat belt hook RH
17. Luggage floor rear spacer RH
18. Spare tire clamp
: Clip
: Pawl
: Metal clip
: Vehicle front
LUGGAGE FLOOR TRIM
INT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
• Never damage the body.
REMOVE
1.
Remove back door weather-strip.
• TYPE1: Refer to
DLK-170, "BACK DOOR WEATHER-STRIP : Removal and Installation"
.
• TYPE2: Refer to
DLK-333, "BACK DOOR WEATHER-STRIP : Removal and Installation"
.
• TYPE3: Refer to
DLK-468, "BACK DOOR WEATHER-STRIP : Removal and Installation"
.
• TYPE4: Refer to
DLK-584, "BACK DOOR WEATHER-STRIP : Removal and Installation"
.
2.
Remove luggage floor board.
3.
Remove luggage floor box. (Models withe 2WD)
4.
Disengage luggage rear plate fixing metal clips with a remover
tool (A), and then remove luggage rear plate.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing luggage rear plate, check that metal clips are securely in body panel holes, and press
them in.
LUGGAGE SIDE LOWER FINISHER
LUGGAGE SIDE LOWER FINISHER : Removal and Installation
INFOID:0000000006418530
REMOVAL
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1.
Remove luggage room lamp. Refer to
INL-39, "Removal and Installation"
2.
Remove luggage floor board.
3.
Remove luggage floor box.(Models with 2WD)
4.
Remove luggage rear plate. Refer to
INT-30, "LUGGAGE REAR PLATE : Removal and Installation"
5.
Remove rear body side welt. Refer to
INT-20, "BODY SIDE WELT : Removal and Installation"
6.
Remove rear seat cushion.
• 2WD models: Refer to
SE-33, "SEAT CUSHION : Removal and Installation"
.
• 4WD models: Refer to
SE-42, "SEAT CUSHION : Removal and Installation"
.
7.
Remove rear seat back.
• 2WD models: Refer to
SE-33, "SEATBACK : Removal and Installation"
.
• 4WD models: Refer to
SE-43, "SEATBACK : Removal and Installation"
.
8.
Remove side hinge.
• 2WD models: Refer to
SE-38, "SEATBACK HINGE : Removal and Installation"
.
• 4WD models: Refer to
SE-48, "SEATBACK HINGE : Removal and Installation"
.
: Metal clip
JMJIA4404ZZ
INT-32
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
9.
Disengage luggage side lower finisher fixing clips with a
remover tool (A), and then remove luggage side lower finisher.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing luggage side lower finisher, check that clips are securely in body panel holes, and
press them in.
Removal and installation of shock absorber mask
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
Disengage shock absorber mask fixing pawls with a remover tool
(A), and then remove shock absorber mask.
CAUTION:
Apply protective tape (B) on the parts to protect it from damage.
INSTALLATION
Install in the reverse order of removal.
Removal and installation of luggage side lower finisher grille
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
Disengage luggage side lower finisher grille fixing pawls with a
remover tool (A), and then remove luggage side lower finisher grille.
CAUTION:
Apply protective tape (B) on the parts to protect it from damage.
INSTALLATION
Install in the reverse order of removal.
LUGGAGE SIDE UPPER FINISHER
LUGGAGE SIDE UPPER FINISHER : Removal and Installation
INFOID:0000000006418531
REMOVAL
: Clip
JMJIA4405ZZ
: Pawl
JMJIA4407ZZ
: Pawl
JMJIA4408ZZ
LUGGAGE FLOOR TRIM
INT-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
CAUTION:
• When removing, always use a remover tool that is made of plastic.
• Never damage the body.
1.
Remove luggage side lower finisher. Refer to
INT-31, "LUGGAGE SIDE LOWER FINISHER : Removal
2.
Remove rear seat belt (floor) anchor bolt. Refer to
SB-12, "SEAT BELT RETRACTOR : Removal and
.
3.
Disengage luggage side upper finisher fixing clips and metal
clips with a remover tool (A), and then remove luggage side
upper finisher.
INSTALATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing luggage side upper finisher, check that clips, and metal clips are securely in body
panel holes, and press them in.
: Clip
: Metal clip
JMJIA4406ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст