Juke F15 (2012 year). Service Repair Manual — part 93

DLK-480

< REMOVAL AND INSTALLATION >

[TYPE 3]

BACK DOOR LOCK

BACK DOOR LOCK

Exploded View

INFOID:0000000006600617

DOOR LOCK

DOOR LOCK : Removal and Installation

INFOID:0000000006600618

REMOVAL

1.

Remove the back door lower finisher. Refer to

INT-35, "BACK DOOR LOWER FINISHER : Removal and

Installation"

.

2.

Remove back door lock assembly mounting bolts.

3.

Disconnect back door lock connector, and then remove back door lock assembly.

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

After installation, check back door open/close, and lock/unlock operation.

EMERGENCY LEVER

EMERGENCY LEVER : Unlock procedures

INFOID:0000000006600619

UNLOCK PROCEDURES

NOTE:
If back door lock cannot be unlocked due to a malfunction or battery discharge, follow the procedures to
unlock back door.

1.

Remove emergency lid. Refer to

INT-36, "EMERGENCY LID : Removal and Installation"

.

1.

Back door lock assembly

2.

TORX bolt

3.

Back door striker

: Do not reuse

: N·m (kg-m, ft-lb)

: Body grease

JMKIA5714GB

BACK DOOR LOCK

DLK-481

< REMOVAL AND INSTALLATION >

[TYPE 3]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

2.

From inside the vehicle, rotate emergency lever toward lower
direction and unlock.

JMKIA5356ZZ

DLK-482

< REMOVAL AND INSTALLATION >

[TYPE 3]

FUEL FILLER LID OPENER

FUEL FILLER LID OPENER

Exploded View

INFOID:0000000006600620

FUEL FILLER LID

FUEL FILLER LID : Removal and Installation

INFOID:0000000006600621

REMOVAL

1.

Fully open fuel filler lid.

2.

Remove fuel mounting pin (1).

3.

Remove mounting screws, and then remove fuel filler lid.

INSTALLATION

Note the following items, and install in the reverse order of removal.

1.

Fuel filler lid opener cable

2.

Cable protector

3.

Fuel filler lid lock assembly

4.

Fuel filler lid assembly

5.

Spring

6.

Bumper rubber

: Clip

: Do not reuse

JMKIA5716ZZ

JMKIA5717ZZ

FUEL FILLER LID OPENER

DLK-483

< REMOVAL AND INSTALLATION >

[TYPE 3]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

CAUTION:

• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply the touch-up paint (the body color) onto the head of the mounting screws.
NOTE:
• The following table shows the specifide values for checking nomal installation status.
• Fitting adjustment cannot be perfomed.

Unit: mm (in)

FUEL FILLER OPENER CABLE

FUEL FILLER OPENER CABLE : Removal and Installation

INFOID:0000000006600622

REMOVAL

1.

Remove hood lock control cable assembly from instrument lower panel (LH). Refer to

DLK-471, "HOOD

LOCK CONTROL CABLE : Removal and Installation"

.

2.

Remove fuel filler lid opener cable (2) from fuel filler lid opener
lever (1).

3.

Remove front kicking plate inner (RH) and rear kicking plate inner (RH). Refer to

INT-19, "KICKING

PLATE INNER : Removal and Installation"

.

4.

Remove dash side finisher (RH). Refer to

INT-20, "DASH SIDE FINISHER : Removal and Installation"

.

5.

Remove center pillar lower garnish (RH). Refer to

INT-20, "CENTER PILLAR LOWER GARNISH :

Removal and Installation"

.

6.

Remove luggage side lower finisher (RH). Refer to

INT-31, "LUGGAGE SIDE LOWER FINISHER :

Removal and Installation"

.

7.

Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to

DLK-484, "FUEL FILLER LID

LOCK : Removal and Installation"

.

8.

Disengage each harness protector (1), and then remove fuel
filler lid opener cable (2).

9.

Remove fuel filler lid opener cable fixing clips, and then remove fuel filler lid opener cable.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

FUEL FILLER LID LOCK

Clearance

Evenness

Fuel filler lid – Body side outer

2.0 – 4.0 (0.079 – 0.157)

(-1.0) – (+1.0) [(-0.039) – (+0.039)]

JMKIA5672ZZ

JMKIA5720ZZ

DLK-484

< REMOVAL AND INSTALLATION >

[TYPE 3]

FUEL FILLER LID OPENER

FUEL FILLER LID LOCK : Removal and Installation

INFOID:0000000006600623

REMOVAL

1.

Fully open fuel filler lid.

2.

Remove luggage side lower finisher (RH). Refer to

INT-31, "LUGGAGE SIDE LOWER FINISHER :

Removal and Installation"

.

3.

Rotate and disengage fuel filler lid lock assembly, and then
remove fuel filler lid lock assembly.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.

4.

Disengage fuel filler lid opener cable (1). Remove fuel filler lid
opener cable while pressing stopper pin (2).

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

JMKIA5718ZZ

JMKIA5719ZZ

DOOR SWITCH

DLK-485

< REMOVAL AND INSTALLATION >

[TYPE 3]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR SWITCH

Exploded View

INFOID:0000000006620631

Removal and Installation

INFOID:0000000006620632

REMOVAL

Remove the TORX bolt (A), and then remove door switch (1).

INSTALLATION

Install in the reverse order of removal.

1.

Door switch

2.

TORX bolt

JMKIA2569GB

JMKIA2173ZZ

DLK-486

< REMOVAL AND INSTALLATION >

[TYPE 3]

REMOTE KEYLESS ENTRY RECEIVER

REMOTE KEYLESS ENTRY RECEIVER

Removal and Installation

INFOID:0000000006620633

REMOVAL

1.

Remove the glove box assembly. Refer to

IP-13, "Removal and Installation"

.

2.

Remove the remote keyless entry receiver (1) mounting bolt (A),
and then remove remote keyless entry receiver.

INSTALLATION

Install in the reverse order of removal.

JMKIA6084ZZ

KEYFOB BATTERY

DLK-487

< REMOVAL AND INSTALLATION >

[TYPE 3]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

KEYFOB BATTERY

Exploded View

INFOID:0000000006445312

Removal and Installation

INFOID:0000000006445313

REMOVAL

1.

Remove screw (9) on the rear of keyfob.

2.

Place the key with the lower case (8) facing up. Set a screw-driver wrapped with tape between upper case
(1) and lower case (8) and then separate the lower case (8) from the upper case (1).

CAUTION:

• Do not touch the circuit board or battery terminal.
• The keyfob is water-resistant. However, if it does get wet, immediately wipe it dry.

3.

When replacing the circuit board assembly, remove circuit board assembly from the upper case (1).
[Circuit board assembly: Switch rubber (4) + Board surface (5)]

CAUTION:

Do not touch the printed circuits directly.

4.

Remove the battery (6) from the lower case (8) and replace it.

CAUTION:

When replacing battery, keep dirt, grease, and other foreign materials off the electrode contact
area.

5.

After replacement, fit the lower and upper cases together, part (4), (7) and tighten with the screw.

CAUTION:

After replacing the battery, Be sure to check that door locking operates normally using the keyfob.
Refer to

DLK-403, "Component Function Check"

.

INSTALLATION

Install in the reverse order of removal.

JMKIA1442ZZ

1.

Upper case

2.

Key

3.

Switch cover

4.

Switch rubber

5.

Board surface

6.

Battery

7.

plate

8.

Lower case

9.

Screw

Battery replacement

: Coin-type lithium battery
(CR1620)

DLK-488

< HOW TO USE THIS MANUAL >

[TYPE 4]

APPLICATION NOTICE

HOW TO USE THIS MANUAL

APPLICATION NOTICE

Information

INFOID:0000000006445320

Check the vehicle type to use the service information in this section.

Service information

Destination

Type 1

With Intelligent Key and super lock

Type 2

With Intelligent Key, without super lock

Type 3

Without Intelligent Key, with super lock

Type 4

Without Intelligent Key and super lock

PRECAUTIONS

DLK-489

< PRECAUTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"

INFOID:0000000006635674

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.

The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

• The vehicle may be equipped with a passenger air bag deactivation switch which can be operated by

the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled and
will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled and
could inflate for certain types of collision. After SRS maintenance or repair, make sure the passenger
air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived for ser-
vice.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution Necessary for Steering Wheel Rotation after Battery Disconnect

INFOID:0000000006635675

NOTE:
• Before removing and installing any control units, first turn the ignition switch to the LOCK position, then dis-

connect both battery cables.

• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both

battery cables.

• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.

If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.

For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.

DLK-490

< PRECAUTION >

[TYPE 4]

PRECAUTIONS

OPERATION PROCEDURE

1.

Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.

2.

Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)

3.

Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.

4.

Perform the necessary repair operation.

5.

When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)

6.

Perform self-diagnosis check of all control units using CONSULT-III.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000006635676

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.

Work

INFOID:0000000006303132

• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their

operational.

• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

PIIB3706J

PREPARATION

DLK-491

< PREPARATION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

PREPARATION

PREPARATION

Commercial Service Tools

INFOID:0000000006303134

Tool name

Description

Engine ear

Locating the noise

Remover tool

Remove the clips, pawls, and metal clips

Power tool

SIIA0995E

PIIB7923J

PIIB1407E

DLK-492

< SYSTEM DESCRIPTION >

[TYPE 4]

COMPONENT PARTS

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location

INFOID:0000000006528614

Component Description

INFOID:0000000006528615

1.

Combination meter

2.

Key switch

3.

BCM
Refer to

BCS-96, "BODY CONTROL

SYSTEM : Component Parts Loca-
tion"

4.

Power window main switch
(door lock/unlock switch)

5.

Front door switch (driver side)

6.

Front door lock assembly (driver
side)

7.

Back door lock assembly

8.

Air bag diagnosis sensor unit
Refer to

SRC-7, "Component Parts

Location"

9.

Remote keyless entry receiver

A.

View with the glove box assembly re-
moved

JMKIA5929ZZ

Item

Function

Air bag diagnosis sensor unit

Transmits air bag signal to BCM.

Back door lock assembly

Opens the back door with the back door open signal from BCM.

BCM

Controls the door lock system.

Combination meter

• Performs operation method guide and warning with buzzer.
• Transmits vehicle seep signal to CAN communication line.

COMPONENT PARTS

DLK-493

< SYSTEM DESCRIPTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Door lock actuator

• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.

Door lock and unlock switch

Transmits door lock/unlock operation to BCM.

Door switch

Detects door open/close condition.

Keyfob

Transmits button operation to remote keyless entry receiver.

Key switch

Key switch detects that ignition key is inserted into the ignition key cylinder, and
then transmits the signal to BCM.

Remote keyless entry receiver

Receives keyfob operation and transmits to BCM.

Item

Function

DLK-494

< SYSTEM DESCRIPTION >

[TYPE 4]

POWER DOOR LOCK SYSTEM

POWER DOOR LOCK SYSTEM

System Diagram

INFOID:0000000006303143

System Description

INFOID:0000000006303144

DOOR LOCK FUNCTION

• The door lock and unlock switch (driver side) is build into power window main switch.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are

locked.

• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors and

are unlocked.

AIR BAG INTERLOCK UNLOCK FUNCTION

When ignition switch is ON and BCM receives air bag signal, it operates automatically to unlock all doors. Air
bag diagnosis sensor unit sends the air bag signal to BCM.

OPERATION CONDITION

If all of the following conditions are satisfied, door lock and unlock operation is performed using the door lock/
unlock switch.

*

1

: While door lock and unlock switch is pressed in the lock direction during this state, combination meter buzzer sounds and warns.

*

2

: When this item becomes OK according to keyfob ID verification, door lock/unlock operation is allowed.

KEY REMINDER FUNCTION

• When door lock and unlock switch and driver door lock knob are operated while key is inserted into key

switch and driver side door is open, door locks once but immediately unlocks. This operation prevents key-
fob from being left in the vehicle.

• While door lock and unlock switch is pressed in the lock direction, combination meter buzzer sounds and

warns.

OVERRIDE FUNCTION

When inside handle of front door is operated while doors are in lock states, lock state of the applicable door
lock becomes invalid and the door is open.

UNLOCK LINK FUNCTION

JMKIA6001GB

Door lock and unlock switch operation

Operation condition

LOCK

• Ignition Key is removed from ignition key cylinder and closed driver

side door*

1

• Doors other than drivers door are closed*

1

• Door are not locked by keyfob*

2

• Door lock that is requested is not auto door lock*

2

UNLOCK

Door are not locked by keyfob*

2

POWER DOOR LOCK SYSTEM

DLK-495

< SYSTEM DESCRIPTION >

[TYPE 4]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

When driver side door or passenger side door is opened, all doors are unlocked.
Unlock function operates when driver door or passenger door is open while all of the following conditions are
satisfied.

NOTE:
When anti-hijack function is activated, only the applicable door is unlocked.

AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (LOCK OPERATION)

The interlock door lock function is the function that locks all doors linked with the vehicle speed or shift posi-
tion. It has 2 types as follows.

Vehicle Speed Sensing Auto Door Lock*1

All doors are locked when the vehicle speed reaches 10 km/h (6MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 10 km/h (6 MPH) or more.

P Range Interlock Door Lock*

2

All doors are locked when shifting the selector lever from the P position to any position other than P.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is in the ON posi-
tion and the shift signal received from the TCM via CAN communication is shifted from the P position to any
position other than P.

Setting change of Automatic Door Lock/Unlock Function

The lock operation setting of the automatic door lock/unlock function can be changed.

With CONSULT-III

The ON/OFF switching of the automatic door lock function and the type selection of the automatic door lock/
unlock function can be performed at the WORK SUPPORT setting of CONSULT-III.

Without CONSULT- III

The automatic door lock function ON/OFF can be switched by performing the following operation.

1.

Close all doors (door switch OFF)

2.

Turn ignition switch ON

3.

Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.

4.

The switching is completed when the hazard warning lamp blinks.

AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (UNLOCK OPERATION)

The automatic door lock/unlock function is the function that unlocks all doors linked with the key position or
shift position. It has 2 types as follows.

IGN OFF Interlock Door Unlock*1

All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.

P Range Interlock Door Unlock*

2

All doors are unlocked when shifting the selector lever from any position other than the P to P position.
BCM outputs the unlock signal to all door lock actuators when it detects that the ignition switch is in the ON
position and the shift signal received from TCM via CAN communication is shifted from any position other than
the P to P position.

Key out Interlock Door Unlock

When ignition key is removed from ignition knob switch, all doors unlock.
When BCM detects that ignition key is removed from ignition knob switch, BCM transmits unlock signal to all
door lock actuators.

Operation condition

• Doors are locked by door lock/unlock switch
• Driver or passenger door switch is switched from OFF to ON
• Anti-hijack function is not activated
• Vehicle speed is 5 km/h (3 MPH) or less

OFF

→

ON

: 2 blinks

ON

→

OFF

: 1 blink