Juke F15 (2012 year). Service Repair Manual — part 100
DLK-592
< REMOVAL AND INSTALLATION >
[TYPE 4]
FRONT DOOR LOCK
8.
Remove front gasket (1) and rear gasket (2).
9.
Slide outside handle bracket toward rear of vehicle to remove.
10. Disconnect outside handle cable (1) from outside handle bracket
(2).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing key rod, rotate key rod holder until a click is felt.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
: Vehicle front
JMKIA5889ZZ
: Vehicle front
JMKIA5890ZZ
JMKIA5891ZZ
REAR DOOR LOCK
DLK-593
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK
Exploded View
INFOID:0000000006628075
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000006628076
REMOVAL
1.
Remove rear door glass and rear door lower sash (rear). Refer to
GW-21, "Removal and Installation"
.
2.
Remove inside handle. Refer to
DLK-594, "INSIDE HANDLE : Removal and Installation"
.
3.
Remove outside handle. Refer to
DLK-594, "OUTSIDE HANDLE : Removal and Installation"
.
4.
Remove door lock assembly TORX bolts.
5.
Disconnect door lock actuator connector, and then remove door lock assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.
• Check door open/close, lock/unlock operation after installation.
1.
Outside handle assembly
2.
Rear door sealing screen
3.
Door lock assembly
4.
TORX bolt
5.
Inside handle
: Clip
: Pawl
: Vehicle front
: Do not reuse
: N·m (kg-m, in-lb)
: Body grease
JMKIA5893GB
DLK-594
< REMOVAL AND INSTALLATION >
[TYPE 4]
REAR DOOR LOCK
• Check door lock assembly for poor lubrication. Apply body
grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000006628077
REMOVAL
1.
Remove rear door finisher. Refer to
INT-16, "Removal and Installation"
.
2.
Remove upper side of sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape do not remain on the sealing screen, if the sealing
screen is reused.
3.
Remove inside handle mounting bolt (A).
4.
Disengage inside handle (1) from door panel (2) while sliding
inside handle toward vehicle rear, and then separate inside han-
dle.
5.
Disengage inside handle cable (3) and lock knob cable (2), and
then remove inside handle (1).
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000006628078
REMOVAL
1.
Remove rear door finisher and rear door corner cover inner. Refer to
INT-16, "Removal and Installation"
2.
Remove rear door sealing screen.
: Grease up point
JMKIA5892ZZ
: Vehicle front
JMKIA5884ZZ
JMKIA5885ZZ
REAR DOOR LOCK
DLK-595
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Rotate stopper (1) upward.
4.
Disengage outside handle cable (2), and then remove outside
handle cable from outside handle assembly (3).
5.
Remove outside handle assembly mounting bolts (A).
6.
Disengage mounting clips using a remover tool (A), and then
remove outside handle assembly.
CAUTION:
Apply protective tape (B) on the door panel to protect the
painted surface from damage.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse rear door sealing screen. Always replace it with a new one when it is removed.
When installing rear door sealing screen, install it according to the following procedure.
- Put lower portion of rear door sealing screen (1) into inside of
door panel (2).
- Perform positioning according to the following procedure,
and then install rear door sealing screen.
• Align upper portion of rear door sealing screen to hole (A) of
door panel as shown in the figure.
• Align hole of rear door sealing screen to edge (B) of door
panel as shown in the figure.
• Be careful to position outside handle cable normally when installing it. For details, refer to
.
• Check door open/close, lock/unlock operation after installation.
JMKIA5894ZZ
JMKIA5895ZZ
: Clip
JMKIA5896ZZ
JMKIA5897ZZ
DLK-596
< REMOVAL AND INSTALLATION >
[TYPE 4]
BACK DOOR LOCK
BACK DOOR LOCK
Exploded View
INFOID:0000000006600682
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000006600683
REMOVAL
1.
Remove the back door lower finisher. Refer to
INT-35, "BACK DOOR LOWER FINISHER : Removal and
.
2.
Remove back door lock assembly mounting bolts.
3.
Disconnect back door lock connector, and then remove back door lock assembly.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check back door open/close, and lock/unlock operation.
EMERGENCY LEVER
EMERGENCY LEVER : Unlock procedures
INFOID:0000000006600684
UNLOCK PROCEDURES
NOTE:
If back door lock cannot be unlocked due to a malfunction or battery discharge, follow the procedures to
unlock back door.
1.
Remove emergency lid. Refer to
INT-36, "EMERGENCY LID : Removal and Installation"
.
1.
Back door lock assembly
2.
TORX bolt
3.
Back door striker
: Do not reuse
: N·m (kg-m, ft-lb)
: Body grease
JMKIA5714GB
BACK DOOR LOCK
DLK-597
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
From inside the vehicle, rotate emergency lever toward lower
direction and unlock.
JMKIA5356ZZ
DLK-598
< REMOVAL AND INSTALLATION >
[TYPE 4]
FUEL FILLER LID OPENER
FUEL FILLER LID OPENER
Exploded View
INFOID:0000000006628079
FUEL FILLER LID
FUEL FILLER LID : Removal and Installation
INFOID:0000000006600686
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove fuel mounting pin (1).
3.
Remove mounting screws, and then remove fuel filler lid.
INSTALLATION
Note the following items, and install in the reverse order of removal.
1.
Fuel filler lid opener cable
2.
Cable protector
3.
Fuel filler lid lock assembly
4.
Fuel filler lid assembly
5.
Spring
6.
Bumper rubber
: Clip
: Do not reuse
JMKIA5904ZZ
JMKIA5717ZZ
FUEL FILLER LID OPENER
DLK-599
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CAUTION:
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply the touch-up paint (the body color) onto the head of the mounting screws.
NOTE:
• The following table shows the specifide values for checking nomal installation status.
• Fitting adjustment cannot be perfomed.
Unit: mm (in)
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000006628080
REMOVAL
1.
Remove hood lock control cable assembly from instrument lower panel (LH). Refer to
LOCK CONTROL CABLE : Removal and Installation"
.
2.
Remove fuel filler lid opener cable (2) from fuel filler lid opener
lever (1).
3.
Remove front kicking plate inner (LH) and rear kicking plate inner (LH and RH). Refer to
ING PLATE INNER : Removal and Installation"
.
4.
Remove dash side finisher (LH). Refer to
INT-20, "DASH SIDE FINISHER : Removal and Installation"
5.
Remove center pillar lower garnish (LH). Refer to
INT-20, "CENTER PILLAR LOWER GARNISH :
.
6.
Remove luggage side lower finisher (RH). Refer to
INT-31, "LUGGAGE SIDE LOWER FINISHER :
.
7.
Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to
LOCK : Removal and Installation"
.
8.
Disengage each harness protector (1), and then remove fuel
filler lid opener cable (2).
9.
Remove fuel filler lid opener cable fixing clips, and then remove fuel filler lid opener cable.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
FUEL FILLER LID LOCK
Clearance
Evenness
Fuel filler lid – Body side outer
2.0 – 4.0 (0.079 – 0.157)
(-1.0) – (+1.0) [(-0.039) – (+0.039)]
JMKIA5901ZZ
JMKIA5720ZZ
DLK-600
< REMOVAL AND INSTALLATION >
[TYPE 4]
FUEL FILLER LID OPENER
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000006600688
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove luggage side lower finisher (RH). Refer to
INT-31, "LUGGAGE SIDE LOWER FINISHER :
.
3.
Rotate and disengage fuel filler lid lock assembly, and then
remove fuel filler lid lock assembly.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.
4.
Disengage fuel filler lid opener cable (1). Remove fuel filler lid
opener cable while pressing stopper pin (2).
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
JMKIA5718ZZ
JMKIA5719ZZ
DOOR SWITCH
DLK-601
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR SWITCH
Exploded View
INFOID:0000000006620634
Removal and Installation
INFOID:0000000006620635
REMOVAL
Remove the TORX bolt (A), and then remove door switch (1).
INSTALLATION
Install in the reverse order of removal.
1.
Door switch
2.
TORX bolt
JMKIA2569GB
JMKIA2173ZZ
DLK-602
< REMOVAL AND INSTALLATION >
[TYPE 4]
REMOTE KEYLESS ENTRY RECEIVER
REMOTE KEYLESS ENTRY RECEIVER
Removal and Installation
INFOID:0000000006620636
REMOVAL
1.
Remove the glove box assembly. Refer to
IP-13, "Removal and Installation"
2.
Remove the remote keyless entry receiver (1) mounting bolt (A),
and then remove remote keyless entry receiver.
INSTALLATION
Install in the reverse order of removal.
JMKIA6084ZZ
KEYFOB BATTERY
DLK-603
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEYFOB BATTERY
Exploded View
INFOID:0000000006303278
Removal and Installation
INFOID:0000000006303279
REMOVAL
1.
Remove screw (9) on the rear of keyfob.
2.
Place the key with the lower case (8) facing up. Set a screw-driver wrapped with tape between upper case
(1) and lower case (8) and then separate the lower case (8) from the upper case (1).
CAUTION:
• Do not touch the circuit board or battery terminal.
• The keyfob is water-resistant. However, if it does get wet, immediately wipe it dry.
3.
When replacing the circuit board assembly, remove circuit board assembly from the upper case (1).
[Circuit board assembly: Switch rubber (4) + Board surface (5)]
CAUTION:
Do not touch the printed circuits directly.
4.
Remove the battery (6) from the lower case (8) and replace it.
CAUTION:
When replacing battery, keep dirt, grease, and other foreign materials off the electrode contact
area.
5.
After replacement, fit the lower and upper cases together, part (4), (7) and tighten with the screw.
CAUTION:
After replacing the battery, Be sure to check that door locking operates normally using the keyfob.
Refer to
DLK-528, "Component Function Check"
INSTALLATION
Install in the reverse order of removal.
JMKIA1442ZZ
1.
Upper case
2.
Key
3.
Switch cover
4.
Switch rubber
5.
Board surface
6.
Battery
7.
plate
8.
Lower case
9.
Screw
Battery replacement
: Coin-type lithium battery
(CR1620)
DLN-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
DLN
A
B
DLN
N
O
P
CONTENTS
DRIVELINE
TRANSFER: TY21B
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect . . . . . . . . .....
Service Notice or Precautions for Transfer . . . ...
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
SYSTEM DESCRIPTION . . . . . . . .
COMPONENT PARTS . . . . . . . . . ...
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ...
4WD Control Module . . . . . . . . . . . ...
4WD Solenoid . . . . . . . . . . . . . . .
Electric Controlled Coupling . . . . . . . . .
Electric Controlled Coupling Temperature Sensor
4WD Mode Switch . . . . . . . . . . . . ...
4WD Warning Lamp . . . . . . . . . . . .
4WD Mode Indicator Lamp . . . . . . . . . .
Torque Distribution Indicator . . . . . . . . ...
STRUCTURE AND OPERATION . . . . . ...
Sectional View . . . . . . . . . . . . . . .
Operation Principle . . . . . . . . . . . . ..
SYSTEM . . . . . . . . . . . . . . . .
4WD SYSTEM . . . . . . . . . . . . . . ...
4WD SYSTEM : System Diagram . . . . . . ...
4WD SYSTEM : System Description . . . . . ..
4WD SYSTEM : Torque Split Control . . . . . .
4WD SYSTEM : Fail-safe . . . . . . . . . .
4WD SYSTEM : Protection Function . . . . . ...
DIAGNOSIS SYSTEM (4WD CONTROL
MODULE) . . . . . . . . . . . . . . ..
CONSULT-III Function . . . . . . . . . . .
ECU DIAGNOSIS INFORMATION . . . ..
4WD CONTROL MODULE . . . . . . . ...
Reference Value . . . . . . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ...
Protection Function . . . . . . . . . . . . ..
DTC Inspection Priority Chart . . . . . . . . ..
DTC Index . . . . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ..
4WD SYSTEM . . . . . . . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . ...
Work Flow . . . . . . . . . . . . . . . .
Diagnostic Work Sheet . . . . . . . . . . .
WRITING UNIT PARAMETER . . . . . . ..
Description . . . . . . . . . . . . . . . ...
Work Procedure . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
P1804, P1809 4WD CONTROL MODULE . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
P1808 WHEEL SPEED SENSOR . . . . . .
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
P1811 POWER SUPPLY CIRCUIT FOR 4WD
CONTROL MODULE . . . . . . . . . .
DLN-2
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P1813 4WD MODE SWITCH . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
P181B INCOMPLETE SELFSHUT . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P181D ENGINE TORQUE SIGNAL . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P181E STEERING ANGLE SENSOR . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P181F INCOMPLETE CALIBRATION . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P1820 ENGINE SPEED SIGNAL . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P1829 ACCELERATOR PEDAL POSITION
SENSOR . . . . . . . . . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P182D 4WD SOLENOID LEFT . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
P182E 4WD SOLENOID RIGHT . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
P182F COUPLING TEMPERATURE SEN-
SOR LEFT . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
Component Inspection . . . . . . . . . . ....
P1830 ABS OPERATION SIGNAL . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P1831 VDC OPERATION SIGNAL . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P1832 TCS OPERATION SIGNAL . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
P183A COUPLING TEMPERATURE SEN-
SOR RIGHT . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . .
P183B SOLENOID POWER SUPPLY . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
P183C DECEL G SENSOR . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
P183D SIDE G SENSOR . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
P183E YAW RATE SENSOR . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
P183F GEAR POSITION SIGNAL . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
P1840 OUTPUT SPEED SIGNAL . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
P1864 INPUT SPEED SIGNAL . . . . . . .
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
P1865 GEAR RATIO SIGNAL . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
U1000 CAN COMM CIRCUIT . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
U1010 CONTROL UNIT (CAN) . . . . . . .
Description . . . . . . . . . . . . . . . ..
DTC Logic . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
POWER SUPPLY AND GROUND CIRCUIT . .
Diagnosis Procedure . . . . . . . . . . . ...
4WD WARNING LAMP . . . . . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
4WD MODE INDICATOR LAMP (4WD-V) . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
4WD MODE INDICATOR LAMP (4WD) . . .
Component Function Check . . . . . . . . ...
DLN-3
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SYMPTOM DIAGNOSIS . . . . . . . ..
4WD WARNING LAMP DOES NOT TURN ON
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
4WD WARNING LAMP DOES NOT TURN
OFF . . . . . . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
HEAVY TIGHT-CORNER BRAKING SYMP-
TOM OCCURS . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
VEHICLE DOES NOT ENTER 4WD MODE . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
4WD WARNING LAMP BLINKS QUICKLY . ...
Description . . . . . . . . . . . . . . . ..
4WD WARNING LAMP BLINKS SLOWLY . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . .
PERIODIC MAINTENANCE . . . . . . .
TRANSFER OIL . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
Draining . . . . . . . . . . . . . . . . ...
Refilling . . . . . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ...
4WD CONTROL MODULE . . . . . . . . .
Removal and Installation . . . . . . . . . . .
4WD MODE SWITCH . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT REMOVAL AND INSTALLATION . ..
TRANSFER ASSEMBLY . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
RING GEAR SHAFT . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Disassembly . . . . . . . . . . . . . . .
Assembly . . . . . . . . . . . . . . . . .
Adjustment . . . . . . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . ..
DRIVE PINION . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Disassembly . . . . . . . . . . . . . . ..
Assembly . . . . . . . . . . . . . . . ...
Adjustment . . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . ..
TRANSFER CASE . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Disassembly . . . . . . . . . . . . . . ..
Assembly . . . . . . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . ...
General Specifications . . . . . . . . . . ...
Preload Torque . . . . . . . . . . . . . ..
Backlash . . . . . . . . . . . . . . . .
Companion Flange Runout . . . . . . . . .
REAR PROPELLER SHAFT: 3F
φ
16-ETJ75
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . ...
Service Notice or Precautions for Rear Propeller
Shaft . . . . . . . . . . . . . . . . . ..
SYMPTOM DIAGNOSIS . . . . . . .
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . ..
REAR PROPELLER SHAFT . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . .
REAR PROPELLER SHAFT . . . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . ...
General Specifications . . . . . . . . . . ...
Propeller Shaft Runout . . . . . . . . . . ..
Journal Axial Play . . . . . . . . . . . . ..
REAR FINAL DRIVE: RTVS
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . ...
DLN-4
PREPARATION . . . . . . . . . . ..
PREPARATION . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . .
Commercial Service Tools . . . . . . . . . .
SYSTEM DESCRIPTION . . . . . . ...
STRUCTURE AND OPERATION . . . . .
Sectional View . . . . . . . . . . . . . ...
Electric controlled coupling . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . .
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . ..
NVH Troubleshooting Chart . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . ...
REAR DIFFERENTIAL GEAR OIL . . . . ..
Inspection . . . . . . . . . . . . . . . ..
Draining . . . . . . . . . . . . . . . . .
Refilling . . . . . . . . . . . . . . . . ..
REMOVAL AND INSTALLATION . . . ..
FRONT OIL SEAL . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
SIDE OIL SEAL . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
ELECTRIC CONTROLLED COUPLING . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
ELECTRIC CONTROLLED COUPLING OIL
SEAL . . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
UNIT REMOVAL AND INSTALLATION ...
REAR FINAL DRIVE ASSEMBLY . . . . ...
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
UNIT DISASSEMBLY AND ASSEMBLY ..
ELECTRIC CONTROLLED COUPLING . . ..
Exploded View . . . . . . . . . . . . . ..
Disassembly . . . . . . . . . . . . . . ..
Assembly . . . . . . . . . . . . . . . ..
Inspection . . . . . . . . . . . . . . . ..
CENTER STEM ASSEMBLY . . . . . . ...
Exploded View . . . . . . . . . . . . . ..
Disassembly . . . . . . . . . . . . . . ..
Assembly . . . . . . . . . . . . . . . ..
Adjustment . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . ..
DRIVE PINION . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Disassembly . . . . . . . . . . . . . . ..
Assembly . . . . . . . . . . . . . . . ..
Adjustment . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . .
General Specification . . . . . . . . . . .
Drive Gear Runout . . . . . . . . . . . .
Preload Torque . . . . . . . . . . . . . .
Backlash . . . . . . . . . . . . . . . ...
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст