Juke F15 (2012 year). Service Repair Manual — part 41

BRAKE WARNING LAMP

BRC-213

< DTC/CIRCUIT DIAGNOSIS >

[WITH ESP]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

BRAKE WARNING LAMP

Component Function Check

INFOID:0000000006601918

1.

CHECK BRAKE WARNING LAMP FUNCTION (1)

Check that brake warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.

CAUTION:

Never start engine.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Proceed to

BRC-208, "Diagnosis Procedure"

.

2.

CHECK BRAKE WARNING LAMP FUNCTION (2)

Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
NOTE:
Brake warning lamp turns ON when parking brake is operated (when parking brake switch is ON).

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check parking brake switch system. Refer to

BRC-208, "Diagnosis Procedure"

.

3.

CHECK BRAKE WARNING LAMP FUNCTION (3)

Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated
while brake fluid level in reservoir tank is with the specified level.
NOTE:
Brake warning lamp turns ON when brake fluid is less than the specified level (when brake fluid level switch is
ON).

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check brake fluid level switch system. Refer to

BRC-208, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006601919

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-

CUIT

Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
Refer to

BRC-205, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

PERFORM THE SELF-DIAGNOSIS

With CONSULT-III.

Perform self-diagnosis for “ABS”.

Is any DTC detected?

YES

>> Check the DTC. Refer to

BRC-142, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK COMBINATION METER

Check combination meter. Refer to

MWI-23, "CONSULT-III Function"

.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit). Refer to

BRC-233, "Removal and Installa-

tion"

.

NO

>> Repair or replace combination meter. Refer to

MWI-69, "Removal and Installation"

.

BRC-214

< DTC/CIRCUIT DIAGNOSIS >

[WITH ESP]

ESP WARNING LAMP

ESP WARNING LAMP

Component Function Check

INFOID:0000000006387354

1.

CHECK ESP WARNING LAMP FUNCTION

Check that ESP warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.

CAUTION:

Never start engine.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to diagnosis procedure. Refer to

BRC-214, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006387355

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-

CUIT

Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
Refer to

BRC-205, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

PERFORM THE SELF-DIAGNOSIS

With CONSULT-III.

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Check the DTC. Refer to

BRC-142, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK ESP WARNING LAMP SIGNAL

With CONSULT-III.

1.

Select “ABS”, “DATA MONITOR” and “SLIP/VDC LAMP” according to this order.

2.

Turn the ignition switch OFF.

3.

Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON, and then
changes to “Off”.

CAUTION:

Never start engine.

Is the inspection result normal?

YES

>> Check combination meter. Refer to

MWI-23, "CONSULT-III Function"

.

NO

>> Replace ABS actuator and electric unit (control unit). Refer to

BRC-233, "Removal and Installa-

tion"

.

ESP OFF INDICATOR LAMP

BRC-215

< DTC/CIRCUIT DIAGNOSIS >

[WITH ESP]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

ESP OFF INDICATOR LAMP

Component Function Check

INFOID:0000000006387356

1.

CHECK ESP OFF INDICATOR LAMP FUNCTION (1)

Check that ESP OFF indicator lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.

CAUTION:

Never start engine.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Proceed to diagnosis procedure. Refer to

BRC-215, "Diagnosis Procedure"

.

2.

CHECK ESP INDICATOR LAMP FUNCTION (2)

Check that ESP OFF indicator lamp in combination meter turns ON/OFF when ESP OFF switch is operated.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Check ESP OFF switch system. Refer to

BRC-210, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006387357

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-

CUIT

Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
Refer to

BRC-205, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

CHECK ESP OFF INDICATOR LAMP SIGNAL (1)

With CONSULT-III.

1.

Select “ABS”, “DATA MONITOR” and “OFF LAMP” according to this order.

2.

Turn the ignition switch OFF.

3.

Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON, and then
changes to “Off”.

CAUTION:

Never start engine.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace ABS actuator and electric unit (control unit). Refer to

BRC-233, "Removal and Installa-

tion"

.

3.

CHECK ESP OFF INDICATOR LAMP SIGNAL (2)

With CONSULT-III.

1.

Select “ABS”, “DATA MONITOR” and “OFF LAMP” according to this order.

2.

Check that data monitor displays “On” or “Off” each time when ESP OFF switch is operated.

Is the inspection result normal?

YES

>> Check combination meter. Refer to

MWI-23, "CONSULT-III Function"

.

NO

>> Check ESP OFF switch system. Refer to

BRC-210, "Diagnosis Procedure"

.

BRC-216

< SYMPTOM DIAGNOSIS >

[WITH ESP]

EXCESSIVE OPERATION FREQUENCY

SYMPTOM DIAGNOSIS

EXCESSIVE OPERATION FREQUENCY

Description

INFOID:0000000006601920

ESP function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD) function
operates in excessive operation frequency.

Diagnosis Procedure

INFOID:0000000006601921

1.

CHECK BRAKING FORCE

Check brake force using a brake tester.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check brake system.

2.

CHECK FRONT AND REAR AXLE

Check that there is no excessive looseness in front and rear axle.
• Front axle
- MR16DDT: Refer to

FAX-9, "Inspection"

.

- HR16DE: Refer to

FAX-41, "Inspection"

.

- K9K: Refer to

FAX-66, "Inspection"

.

• Rear axle
- 2WD: Refer to

RAX-4, "Inspection"

.

- 4WD: Refer to

RAX-12, "Inspection"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts.

3.

CHECK WHEEL SENSOR

Check wheel sensor.
• Check installation and damage of wheel sensor.
• Check connection of wheel sensor harness connector.
• Check terminal of wheel sensor harness connector.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>>

Repair or replace wheel sensor.

• Front wheel sensor: Refer to

BRC-224, "FRONT WHEEL SENSOR : Removal and Installation"

.

• Rear wheel sensor: Refer to

BRC-227, "REAR WHEEL SENSOR : Removal and Installation"

.

4.

CHECK SENSOR ROTOR

Check that there is no looseness, damage or foreign material on sensor rotor.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>>

Repair installation or replace sensor rotor.

• Front sensor rotor: Refer to

BRC-229, "FRONT SENSOR ROTOR : Removal and Installation"

.

• Rear sensor rotor. Refer to

BRC-227, "REAR WHEEL SENSOR : Removal and Installation"

.

5.

CHECK WARNING LAMP TURNS OFF

Check that ABS warning lamp, brake warning lamp and ESP warning lamp turn OFF approx. 1 second after
key switch is turned ON and stay in OFF status during driving.

CAUTION:

Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).

Is the inspection result normal?

YES

>> Normal

NO

>> Perform self-diagnosis for “ABS” with CONSULT-III.

UNEXPECTED BRAKE PEDAL REACTION

BRC-217

< SYMPTOM DIAGNOSIS >

[WITH ESP]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

UNEXPECTED BRAKE PEDAL REACTION

Description

INFOID:0000000006601922

A malfunction of brake pedal feel (height or others) is detected when brake pedal is depressed.

Diagnosis Procedure

INFOID:0000000006601923

1.

CHECK FRONT AND REAR AXLE

Check that there is no excessive looseness in front and rear axle.
• Front axle
- MR16DDT: Refer to

FAX-9, "Inspection"

.

- HR16DE: Refer to

FAX-41, "Inspection"

.

- K9K: Refer to

FAX-66, "Inspection"

.

• Rear axle
- 2WD: Refer to

RAX-4, "Inspection"

.

- 4WD: Refer to

RAX-12, "Inspection"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace error-detected parts.

2.

CHECK DISC ROTOR

Check disc rotor runout.
• Front
- LHD: Refer to

BR-16, "DISC ROTOR : Inspection and Adjustment"

.

- RHD: Refer to

BR-84, "DISC ROTOR : Inspection and Adjustment"

.

• Rear
- LHD: Refer to

BR-18, "DISC ROTOR : Inspection and Adjustment"

.

- RHD: Refer to

BR-86, "DISC ROTOR : Inspection and Adjustment"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>>

Refinish disc rotor.

• Front
- LHD: Refer to

BR-16, "DISC ROTOR : Inspection and Adjustment"

.

- RHD: Refer to

BR-84, "DISC ROTOR : Inspection and Adjustment"

.

• Rear
- LHD: Refer to

BR-18, "DISC ROTOR : Inspection and Adjustment"

.

- RHD: Refer to

BR-86, "DISC ROTOR : Inspection and Adjustment"

.

3.

CHECK BRAKE FLUID LEACKAGE

Check fluid leakage.
• Front
- LHD: Refer to

BR-30, "FRONT : Inspection"

.

- RHD: Refer to

BR-97, "FRONT : Inspection"

.

• Rear
- LHD: Refer to

BR-39, "REAR : Inspection"

.

- RHD: Refer to

BR-105, "REAR : Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK BRAKE PEDAL

Check each item of brake pedal.
• LHD: Refer to

BR-9, "Inspection and Adjustment"

.

• RHD: Refer to

BR-77, "Inspection and Adjustment"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>>

Adjust each item of brake pedal.

• LHD: Refer to

BR-9, "Inspection and Adjustment"

.

BRC-218

< SYMPTOM DIAGNOSIS >

[WITH ESP]

UNEXPECTED BRAKE PEDAL REACTION

• RHD: Refer to

BR-77, "Inspection and Adjustment"

.

5.

CHECK BRAKING FORCE

Check brake force using a brake tester.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Check each components of brake system.

6.

CHECK BRAKE PERFORMANCE

Disconnect ABS actuator and electric unit (control unit) connector so that ABS does not operate. Check that
brake force is normal in this condition. Connect harness connectors after checking.

Is the inspection result normal?

YES

>> Normal

NO

>> Check each components of brake system.

THE BRAKING DISTANCE IS LONG

BRC-219

< SYMPTOM DIAGNOSIS >

[WITH ESP]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

THE BRAKING DISTANCE IS LONG

Description

INFOID:0000000006601924

Brake stopping distance is long when ABS function is operated.

Diagnosis Procedure

INFOID:0000000006601925

CAUTION:

Brake stopping distance on slippery road like rough road, gravel road or snowy road may become
longer when ABS is operated than when ABS is not operated.

1.

CHECK BRAKING FORCE

Check brake force using a brake tester.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check each components of brake system.

2.

CHECK BRAKE PERFORMANCE

Disconnect ABS actuator and electric unit (control unit) connector so that ABS does not operate. Check brake
stopping distance in this condition. Connect harness connectors after checking.

Is the inspection result normal?

YES

>> Normal

NO

>> Check each components of brake system.

BRC-220

< SYMPTOM DIAGNOSIS >

[WITH ESP]

DOES NOT OPERATE

DOES NOT OPERATE

Description

INFOID:0000000006601926

ESP function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD) function
does not operate.

Diagnosis Procedure

INFOID:0000000006601927

CAUTION:

• ESP function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD)

function never operate when the vehicle speed is 10 km/h (6.2 MPH) or less.

• ESP function and TCS function never operate when ESP OFF switch is operated (when ESP OFF

indicator lamp turns ON).

1.

CHECK WARNING LAMP

Check that ABS warning lamp, brake warning lamp and ESP warning lamp turn ON and turn OFF approx. 1
second after key switch is turned ON. Check that ABS warning lamp, brake warning lamp and ESP warning
lamp and stay in OFF status during driving.

CAUTION:

Brake warning lamp turns ON when parking brake is operated (parking brake switch is ON) or brake
fluid is less than the specified level (brake fluid level switch is ON).
Is the inspection result normal?

YES

>> Normal

NO

>> Perform self-diagnosis for “ABS” with CONSULT-III.

BRAKE PEDAL VIBRATION OR OPERATION SOUND OCCURS

BRC-221

< SYMPTOM DIAGNOSIS >

[WITH ESP]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

BRAKE PEDAL VIBRATION OR OPERATION SOUND OCCURS

Description

INFOID:0000000006601928

• Brake pedal vibrates and motor sound from ABS actuator and electric unit (control unit) occurs, when the

engine starts.

• Brake pedal vibrates during braking.

CAUTION:

Vibration may be felt during brake pedal is lightly depressed (just placing a foot on it) in the following
conditions. This is normal.
• When shifting gears
• When driving on slippery road
• During cornering at high speed
• When passing over bumps or grooves [Approx. 50 mm (1.97 in) or more]
• When pulling away just after starting engine [at approx. 10 km/h (6.2 MPH) or higher]

Diagnosis Procedure

INFOID:0000000006601929

1.

SYMPTOM CHECK 1

Check that there are pedal vibrations when the engine is started.
Do vibrations occur?

YES

>> GO TO 2.

NO

>>

Check brake pedal.

• LHD: Refer to

BR-22, "Inspection and Adjustment"

.

• RHD: Refer to

BR-90, "Inspection and Adjustment"

.

2.

SYMPTOM CHECK 2

Check that motor noise from ABS actuator and electric unit (control unit) occurs when the engine starts.

Does the operation sound occur?

YES

>> GO TO 3.

NO

>> Perform self-diagnosis for “ABS” with CONSULT-III.

3.

SYMPTOM CHECK 3

Check symptoms when electrical component (headlamps, etc.) switches are operated.
Does the symptom occur?

YES

>> Check that radio (including wiring), antenna and antenna lead-in wires are not located near ABS

actuator and electric unit (control unit). Move them if they are located near ABS actuator and elec-
tric unit (control unit).

NO

>> Normal

BRC-222

< SYMPTOM DIAGNOSIS >

[WITH ESP]

VEHICLE JERKS DURING

VEHICLE JERKS DURING

Description

INFOID:0000000006601930

The vehicle jerks when ESP function, TCS function, ABS function, EBD function or brake limited slip differen-
tial (BLSD) function operates.

Diagnosis Procedure

INFOID:0000000006601931

1.

CHECK SYMPTOM

Check that the vehicle jerks when ESP function, TCS function, ABS function, EBD function or brake limited
slip differential (BLSD) function operates.

Is the inspection result normal?

YES

>> Normal

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT-III.

Perform self-diagnosis for “ABS”.
Is any DTC detected?

YES

>> Check the DTC. Refer to

BRC-142, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK CONNECTOR

With CONSULT-III.

1.

Turn the ignition switch OFF.

2.

Disconnect ABS actuator and electric unit (control unit) harness connector.

3.

Check connector terminal for deformation, disconnection and looseness.

4.

Connect harness connector and perform self-diagnosis for “ABS” again.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Poor connection of connector terminal. Repair or replace connector terminal.

4.

CHECK ECM AND TCM SELF-DIAGNOSIS RESULTS

With CONSULT-III.

Perform self-diagnosis for “ENGINE” and “TRANSMISSION” (for CVT models).

Is any DTC detected?

YES

>> Check the DTC.

NO

>> Replace ABS actuator and electric unit (control unit). Refer to

BRC-233, "Removal and Installa-

tion"

.

NORMAL OPERATING CONDITION

BRC-223

< SYMPTOM DIAGNOSIS >

[WITH ESP]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

NORMAL OPERATING CONDITION

Description

INFOID:0000000006601932

Symptom

Result

Brake pedal slightly vibrates and operation sound (motor sound and sound from suspen-
sion) occurs when ESP function, TCS function, ABS function, EBD function or brake limited
differential (BLSD) function operates.

This is not a malfunction, The symptom
occurs ESP function, TCS function, ABS
function, EBD function and brake limited
differential (BLSD) function that are nor-
mally operated.

Brake stopping distance may become longer than models without ABS function depending
on the road conditions, when ABS function is operated on slippery road like rough road,
gravel road or snowy road.

Brake pedal vibrates and operation sound occurs during sudden acceleration and corner-
ing, when ESP function, TCS function or brake limited slip differential (BLSD) function is op-
erated.

Brake pedal vibrates and motor sound from the engine room occurs, when the engine starts
or the vehicle starts just after starting the engine.

This is not a malfunction, because it is
caused by operation check of ABS actua-
tor and electric unit (control unit).

Acceleration may be felt insufficient depending on the road conditions.

This is not a malfunction, because it is
caused by TCS function that puts the
highest priority to obtain the optimum
traction (stability).

TCS function may operate momentarily, while driving on a road where friction coefficient
varies, or when downshifting, or fully depressing accelerator pedal.

ABS warning lamp and EPS OFF indicator lamp may turn ON, when the vehicle is on a ro-
tating turntable or is given a strong shaking or large vibrations on a ship while the engine is
running.

In this case, restart the engine on a nor-
mal road. If the normal condition is re-
stored, there is no malfunction. In that
case, erase “ABS” self-diagnosis result
memory with CONSULT-III.

ESP warning lamp may turn ON and ESP function, TCS function and brake limited slip dif-
ferential (BLSD) function may not normally operate, when driving on a special road the is
extremely slanted (bank in a circuit course).

A malfunction in yaw rate/side/decel G sensor system may be detected when the vehicle
sharply turns during a spin turn, acceleration turn or drift driving while ESP function, TCS
function and brake limited slip differential (BLSD) function are OFF (ESP OFF switch is
pressed and ESP OFF indicator lamp is in ON status).

The vehicle speed does not increase, when the accelerator pedal is depressed while the
vehicle is on a 2-wheel chassis dynamometer for speedometer check.

This is not a malfunction. (When checking
the vehicle on a chassis dynamometer,
operate ESP OFF switch so that TCS
function is OFF.)

BRC-224

< REMOVAL AND INSTALLATION >

[WITH ESP]

WHEEL SENSOR

REMOVAL AND INSTALLATION

WHEEL SENSOR

FRONT WHEEL SENSOR

FRONT WHEEL SENSOR : Exploded View

INFOID:0000000006601933

NOTE:
Front RH wheel sensor is symmetrically opposite of LH.

FRONT WHEEL SENSOR : Removal and Installation

INFOID:0000000006601934

REMOVAL

1.

Remove tires.

2.

Remove the fender protector (front). Refer to

EXT-22, "Removal and Installation"

.

3.

Remove front wheel sensor from steering knuckle.

CAUTION:

Never rotate and never pull front wheel sensor as much as possible, when pulling out.

4.

Remove front wheel sensor harness from the vehicle.

CAUTION:

Never twist or pull front wheel sensor harness, when removing.

INSTALLATION

Note the following, and install in the reverse order of the removal.

1.

Front LH wheel sensor

2.

Front LH wheel sensor harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

JPFIC0191GB

WHEEL SENSOR

BRC-225

< REMOVAL AND INSTALLATION >

[WITH ESP]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

• Check that there is no foreign material like iron powder or damage on inner surface of front wheel sensor

mounting hole of steering knuckle and sensor rotor. Install after cleaning when there are foreign material like
iron powder, or replace when there is a malfunction.

• Never twist front wheel sensor harness when installing front wheel

sensor. Check that grommet (2) is fully inserted to bracket (1).
Check that front wheel sensor harness is not twisted after installa-
tion.

REAR WHEEL SENSOR

REAR WHEEL SENSOR : Exploded View

INFOID:0000000006601935

2WD

Left side

JPFIC0209ZZ

JPFIC0192GB

1.

Rear LH wheel sensor

2.

Rear LH wheel sensor harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

BRC-226

< REMOVAL AND INSTALLATION >

[WITH ESP]

WHEEL SENSOR

Right side

4WD

JPFIC0218GB

1.

Rear RH wheel sensor

2.

Rear RH wheel sensor harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

WHEEL SENSOR

BRC-227

< REMOVAL AND INSTALLATION >

[WITH ESP]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

NOTE:
Rear RH wheel sensor is symmetrically opposite of LH.

REAR WHEEL SENSOR : Removal and Installation

INFOID:0000000006601936

REMOVAL

1.

Remove rear wheel sensor from wheel hub and bearing assembly (2WD).

CAUTION:

Never rotate or pull rear wheel sensor as much as possible, when pulling out.

2.

Remove rear wheel sensor from axle housing (4WD).

CAUTION:

Never rotate or pull rear wheel sensor as much as possible, when pulling out.

3.

Remove rear wheel sensor harness from the vehicle.

CAUTION:

Never twist and never pull rear wheel sensor harness, when removing.

INSTALLATION

Note the following, and install in the reverse order of the removal.
• Check that there is no foreign material like iron powder or damage on inner surface of rear wheel sensor

mounting hole of wheel hub and bearing assembly and sensor rotor. Install after cleaning when there are for-
eign material like iron powder, or replace when there is a malfunction.

1.

Rear LH wheel sensor

2.

Rear LH wheel sensor harness con-
nector

: Vehicle front

: N·m (kg-m, in-lb)

JSFIA0525GB

BRC-228

< REMOVAL AND INSTALLATION >

[WITH ESP]

WHEEL SENSOR

• Never twist rear wheel sensor harness when installing rear wheel

sensor. Check that grommet (2) is fully inserted to bracket (1).
Check that rear wheel sensor harness is not twisted after installa-
tion.

CAUTION:

Check that the identification line (A) of the rear wheel sensor
is faced upward.

JPFIC0209ZZ

JPFIC0198ZZ