Juke F15 (2012 year). Service Repair Manual — part 209
EXT-8
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Inspection Procedure
INFOID:0000000006483498
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1.
Cluster lid A and instrument panel
2.
Acrylic lens and combination meter housing
3.
Instrument panel to front pillar garnish
4.
Instrument panel to windshield
5.
Instrument panel mounting pins
6.
Wiring harnesses behind the combination meter
7.
A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicon spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Never use silicone spray to isolate a squeak or rattle. If the area is saturated with silicone, the recheck
of repair becomes impossible.
CENTER CONSOLE
Components to pay attention to include:
1.
Shifter assembly cover to finisher
2.
A/C control unit and cluster lid C
3.
Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the following:
1.
Finisher and inner panel making a slapping noise
2.
Inside handle escutcheon to door finisher
3.
Wiring harnesses tapping
4.
Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. The areas can usually be insulated with felt cloth tape or insulator foam blocks to
repair the noise.
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the customer.
In addition look for the following:
1.
Trunk lid dumpers out of adjustment
2.
Trunk lid striker out of adjustment
3.
Trunk lid torsion bars knocking together
4.
A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1.
Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2.
Sunvisor shaft shaking in the holder
3.
Front or rear windshield touching headlining and squeaking
SQUEAK AND RATTLE TROUBLE DIAGNOSES
EXT-9
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
SEATS
When isolating seat noise it is important to note the position the seat is in and the load placed on the seat
when the noise occurs. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1.
Headrest rods and holder
2.
A squeak between the seat pad cushion and frame
3.
Rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1.
Any component mounted to the engine wall
2.
Components that pass through the engine wall
3.
Engine wall mounts and connectors
4.
Loose radiator mounting pins
5.
Hood bumpers out of adjustment
6.
Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
EXT-10
< SYMPTOM DIAGNOSIS >
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Diagnostic Worksheet
INFOID:0000000006483499
PIIB8740E
SQUEAK AND RATTLE TROUBLE DIAGNOSES
EXT-11
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
PIIB8742E
EXT-12
< REMOVAL AND INSTALLATION >
FRONT BUMPER
REMOVAL AND INSTALLATION
FRONT BUMPER
Exploded View
INFOID:0000000006479267
JMKIA5631GB
FRONT BUMPER
EXT-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000006479268
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1.
Fully open hood assembly.
2.
Remove clips (A) of bumper upper side.
3.
Remove front fillet molding front side. Refer to
EXT-26, "FRONT FILLET MOLDING : Removal and Instal-
.
4.
Remove bumper fascia assembly fixing screws (A) (LH and
RH).
5.
Remove air guide fixing screws, and then remove air guide (LH and RH).Refer to
.
6.
Remove clips of bumper lower side.
1.
Front side grille RH
2.
Front side grille LH
3.
Bumper side bracket RH
4.
Front center grille
5.
Emblem
6.
Bumper reinforcement
7.
Energy absorber
8.
Bumper end rubber RH
9.
Bumper fascia
10.
Screw grommet
11.
Bumper bracket cover
12.
License plate bracket
13.
Front fog bracket RH
14.
Bumper fascia lower
15.
U nut
16.
Front fog bracket LH
17.
Bumper end rubber LH
18.
Bumper side bracket LH
19.
Screw grommet
20.
double-sided tape
[t: 1.2 mm (0.047 in)]
: Pawl
: Do not reuse
JMKIA5593ZZ
JMKIA5559ZZ
EXT-14
< REMOVAL AND INSTALLATION >
FRONT BUMPER
7.
Pull bumper fascia side toward the vehicle side to disengage the
fitting of bumper side bracket and bumper fascia side as shown
by the arrow in the figure.
8.
CAUTION:
When removing bumper fascia assembly, 2 workers are
required so as to prevent it from dropping.
9.
Disconnect front fog lamp harness connectors. (with fog lamp)
10. Remove bumper fascia assembly.
11. Remove the following parts after removing bumper fascia assembly.
• Front fog lamp assembly (LH and RH). (with fog lamp)
• Front fog lamp finishers (LH and RH). (with out fog lamp)
• Bumper fascia lower
• License plate bracket
12. Remove bumper energy absorber.
13. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.
14. Remove bumper side bracket mounting screws, and then remove bumper side bracket.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
: Pawl
JMKIA5592ZZ
JMKIA5560ZZ
Portion Clearance
Surface
height
difference
Bumper fascia assembly –
Hood
A – A
2.0 – 6.0 mm
(0.079 – 0.236 in)
(
−
0.2) – (+0.1) mm
[(
−
0.008) – (+0.004) in]
Bumper fascia assembly –
Front center grille
B – B
0.3 – 2.7 mm
(0.012 – 0.106 in)
—
Bumper fascia assembly –
Front side grille
C – C
0.5 – 2.5 mm
(0.020 – 0.098 in)
—
Bumper fascia assembly –
Front combination lamp
D – D
0.5 – 3.5 mm
(0.020 – 0.138 in)
—
Bumper fascia assembly –
Front fender
E – E
0.0 – 1.0 mm
(0.000 –0.039 in)
(
−
0.39) – (+1.7) mm
[(
−
0.012) – (+0.067) in]
REAR BUMPER
EXT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
REAR BUMPER
Exploded View
INFOID:0000000006479269
1.
Bumper side bracket LH
2.
Bumper closing LH
3.
Bumper fascia assembly
4.
Reflex reflector LH
5.
Rear panel lower
6.
U nut
7.
Bumper fascia lower
8.
Reflex reflector RH
9.
Bumper stay LH
JMKIA5647GB
EXT-16
< REMOVAL AND INSTALLATION >
REAR BUMPER
Removal and Installation
INFOID:0000000006479270
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1.
Fully open back door.
2.
Remove bumper fascia mounting screws of rear combination lamp (LH and RH) lower side.
3.
Remove rear fillet molding rear side. Refer to
EXT-27, "REAR FILLET MOLDING : Removal and Installa-
4.
Remove bumper closing.
5.
Remove clips of bumper lower side.
6.
Remove bumper fascia assembly fixing screws (A) (LH and
RH).
7.
Pull bumper fascia side toward the vehicle side to disengage the
fitting of bumper side bracket and bumper fascia side as shown
by the arrow in the figure.
CAUTION:
When removing bumper fascia, 2 workers are required so
as to prevent it from dropping.
8.
Disconnect rear fog lamp harness connector.
9.
Remove bumper fascia assembly.
10. Remove the following parts after removing rear bumper fascia.
• Bumper fascia lower
• Bumper finisher
• Reflex reflector (LH and RH).
11. Remove bumper energy absorber.
12. Remove rear panel lower.
13. Remove bumper stay (LH and RH).
14. Remove bumper side bracket fixing screws, and then remove bumper side bracket (LH and RH).
INSTALLATION
Note the following items, and then install in the reverse order of removal.
10.
screw grommet
11.
Bumper energy absorber
12.
Bumper stay RH
13.
Bumper closing RH
14.
Bumper side bracket RH
: Pawl
: Do not reuse
: N·m (kg-m, ft-lb)
JMKIA5561ZZ
: Pawl
JMKIA5564ZZ
REAR BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
JMKIA5562ZZ
Portion
Clearance
Surface height difference
Bumper fascia assembly –
Rear fender
A – A
0.0 – 1.0 mm
(0.000 – 0.039 in)
(
−
0.3) – (+1.7) mm
[(
−
0.012) – (+0.067) in]
Bumper fascia assembly –
Rear combination lamp
B – B
0.2 – 3.0 mm
(0.008 – 0.118 in)
—
Bumper fascia assembly –
Back door
C – C
3.0 – 7.0 mm
(0.118 – 0.276 in)
0.0 – 4.0 mm
(0.000 – 0.157 in)
D – D
6.0 – 10.0 mm
(0.236 – 0.394 in)
0.0 – 4.0 mm
(0.000 – 0.157 in)
EXT-18
< REMOVAL AND INSTALLATION >
FRONT GRILLE
FRONT GRILLE
Exploded View
INFOID:0000000006479271
Removal and Installation
INFOID:0000000006479272
REMOVAL
CAUTION:
When remove front grilles (1) apply protective tape (A) on the
bumper fascia (2) to protect the painted surface from damage.
1.
Fully open hood assembly.
1.
Bumper fascia assembly
2.
Front side grille RH
3.
Front center grille
4.
Emblem
5.
Front side grille LH
: Pawl
JMKIA5563ZZ
JMKIA5622ZZ
FRONT GRILLE
EXT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2.
Remove front center grille upper fixing clips (A).
CAUTION:
Apply protective tape (B) around bumper fascia.
3.
Disengage fixing pawls from back side while pulling front center
grille to wade vehicle front, and then remove front center grille.
4.
Remove front side grille (LH and RH) upper fixing clips (A).
5.
Disengage fixing pawls from back side of front side grille (LH
and RH).
CAUTION:
Apply protective tape (B) around bumper fascia.
6.
Remove front side grille (LH and RH) to ward vehicle front.
7.
Remove emblem after removing front grille.
INSTALLATION
Install in the reverse order of removal.
JMKIA5623ZZ
: Pawl
JMKIA5756ZZ
: Pawl
JMKIA5624ZZ
EXT-20
< REMOVAL AND INSTALLATION >
COWL TOP
COWL TOP
Exploded View
INFOID:0000000006479273
LHD models
Removal and Installation
INFOID:0000000006479274
REMOVAL
1.
Fully open hood assembly.
JMKIA5620ZZ
1.
Front fender cover RH
2.
Cowl top cover seal
3.
Blind plug RH
4.
Cowl top cover
5.
Cowl top cover cap
6.
Cowl top extension
7.
EPT seal [t: 3.0 mm (0.118 in)]
8.
Air intake cover
9.
Blind plug LH
10. Front fender cover LH
11. Washer nozzle
: Clip
: Pawl
: Do not reuse
COWL TOP
EXT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
2.
Remove front wiper arm (LH and RH). Refer to
WW-76, "Removal and Installation"
.
3.
Disconnect washer tube joint on cowl top cover RH.
4.
Remove front fender cover (LH and RH).
5.
Remove cowl top cover fixing clips.
6.
Pull forward to release cowl top cover from windshield glass.
CAUTION:
When performing the procedure after removing cowl top
cover, cover the lower end of windshield glass with ure-
thane etc.
7.
Remove cowl top cover.
8.
Remove the following parts after removing cowl top cover.
• EPT sealer
• Cowl top seal
• Washer tube
• Washer nozzle (LH and RH). Refer to
WW-87, "Removal and Installation"
9.
Remove front wiper drive assembly. Refer to
WW-80, "Removal and Installation"
10. Remove cowl top extension mounting bolts, and then remove cowl top extension.
INSTALLATION
Note the following items and then, install in the reverse order of removal.
CAUTION:
• Clean the joint between the cowl top cover and the windshield, and then install them.
• Replace the EPT sealer on the back surface with new EPT sealer when reusing the cowl top cover.
• Remove the EPT sealer remaining on the cowl top cover using a double-faced adhesive tape remove.
• To maintain adhesion, never wash the vehicle within 24 hours after installation.
• Perform the stop position adjustment at the installation of the front wiper arms. Refer to
.
JMKIA5621ZZ
EXT-22
< REMOVAL AND INSTALLATION >
FENDER PROTECTOR
FENDER PROTECTOR
Exploded View
INFOID:0000000006479275
Removal and Installation
INFOID:0000000006479276
REMOVAL
1.
Remove front fillet molding. Refer to
EXT-26, "FRONT FILLET MOLDING : Removal and Installation"
.
2.
Remove air guide fixing bolts, and then remove air guide.
3.
Remove front fender protector mounting screws and clips.
4.
Remove front fender protector from wheel house.
INSTALLATION
Install in the reverse order of removal.
1.
Hoodledge insurator
2.
Fender protector
3.
U nut
4.
Air guide
5.
Screw grommet
A.
To hoodledge panel
: Vehicle front
JMKIA5651ZZ
SILL COVER
EXT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
SILL COVER
Exploded View
INFOID:0000000006479277
Removal and Installation
INFOID:0000000006479278
REMOVAL
1.
Remove sill cover front end fixing screw (A).
1.
Screw grommet
2.
Screw grommet
3.
Sill cover
4.
Wind deflector
JMKIA5581ZZ
JMKIA5565ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст