Nissan Versa Sedan. Manual — part 522
FLOOR TRIM
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
FLOOR TRIM
Exploded View
INFOID:0000000009269480
Removal and Installation
INFOID:0000000009269481
REMOVAL
1. Remove front seat assemblies (LH/RH). Refer to
SE-17, "DRIVER SIDE : Removal and Installation"
2. Remove rear seat cushion. Refer to
SE-23, "Removal and Installation - Seat Cushion Assembly"
3. Remove center console lower. Refer to
IP-25, "Removal and Installation"
4. Remove dash side finishers (LH/RH). Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installa-
5. Remove center pillar lower finishers (LH/RH). Refer to
INT-23, "CENTER PILLAR LOWER FINISHER :
.
6. Disconnect diagnosis sensor unit. Refer to
SR-27, "Removal and Installation"
.
7. Remove shift selector assembly.
• 5MT: Refer to
TM-23, "Removal and Installation"
.
• 4AT: Refer to
TM-233, "Removal and Installation"
• CVT: Refer to
TM-429, "Removal and Installation"
1.
Harness clip A
2.
Harness clip B
3.
Floor carpet
4.
Carpet hook
5.
Front floor spacer (RH)
6.
Front floor spacer (LH)
7.
Rear floor spacer (LH)
8.
Rear floor spacer (RH)
Front
Clip
AWJIA0738ZZ
INT-28
< REMOVAL AND INSTALLATION >
FLOOR TRIM
8. Remove A/C unit assembly bolt (C) and bracket (1) from vehicle.
9. Remove instrument panel lower bracket bolt (B) and screw (A)
and reposition bracket as necessary to remove floor carpet.
10. Release carpet hook clip with a suitable tool (A) and remove car-
pet hook.
: Clip
11. Release pawl using a suitable tool (A) and open the harness
clip.
: Pawl
12. Remove floor carpet.
INSTALLATION
Installation is in the reverse order of removal.
ALJIA0712ZZ
AWJIA0736ZZ
AWJIA0737ZZ
HEADLINING
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
HEADLINING
Exploded View
INFOID:0000000009269482
Removal and Installation
INFOID:0000000009269483
REMOVAL
1. Remove front pillar finishers (LH/RH). Refer to
INT-19, "FRONT PILLAR FINISHER : Removal and Instal-
.
2. Remove sun visor assembly screws and sun visor assemblies (LH/RH).
3. Remove passenger seat. Refer to
SE-17, "DRIVER SIDE : Removal and Installation"
NOTE:
Remove passenger seat to make room for headlining removal out of the LH rear door.
4. Remove lamp assemblies. Refer to
INL-50, "Removal and Installation"
(Map Lamp, if equipped) and
52, "Removal and Installation"
1.
Headlining assembly
2.
Sun visor assembly (RH)
3. Sun visor assembly (RH)
4.
Map lamp (if equipped)
5.
Sun visor holder (LH)
6. Sun visor assembly (LH)
7.
Microphone finisher (if equipped)
8.
Room lamp
9. Front assist grip (RH) (if equipped)
10. Rear assist grip (RH) (if equipped) 11. Rear assist grip (LH) (if equipped) A. Headlining clip
Pawl
AWJIA1112ZZ
INT-30
< REMOVAL AND INSTALLATION >
HEADLINING
5. Remove all the assist grips.
a. Release assist grip cover (1).
b. Remove assist grip bolts and assist grip.
6. Remove center pillar upper finishers (LH/RH). Refer to
INT-23, "CENTER PILLAR UPPER FINISHER :
.
7. Remove rear pillar finishers (LH/RH). Refer to
INT-24, "REAR PILLAR FINISHER : Removal and Installa-
8. Insert a suitable tool (A) at approximately a 30 degree angle into
the sun visor holder notch on the front of the sun visor holder (1)
and press in the locking tab (B) to release it. While holding in
lock tab (B), rotate the sun visor holder (1) 90 degrees to release
it from the headlining.
: Front
CAUTION:
Do not force the sun visor holder when removing as the
locking tab may be damaged if the suitable tool is not posi-
tioned correctly.
NOTE:
If the sun visor holder (1) does not fully rotate, make sure that
the suitable tool (A) is pressing in on the locking tab (B) and is
not positioned under locking tab (B). Reinsert the suitable tool
(A) as necessary to release the locking tab (B).
9. Remove headlining clips.
10. Remove headlining assembly through the rear door.
CAUTION:
• Two people are required for removal to prevent damage to
headlining.
• Apply protective tape to the portion where contact may
occur during work.
• Do not bend headlining when removing.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing headlining, start by installing both sun visor holders and headlining clips in order to
keep the headlining in position.
ALJIA1241ZZ
ALJIA0537ZZ
JMJIA6084ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст