Nissan Versa Sedan. Manual — part 520
BODY SIDE TRIM
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000009269470
FRONT PILLAR FINISHER
FRONT PILLAR FINISHER : Removal and Installation
INFOID:0000000009269471
REMOVAL
1. Release front pillar portion of front body side welt.
2. Pull front pillar finisher downward as shown, using mild pressure
to disengage the front pillar finisher from the clips.
: Clip
1.
Rear body side welt
2.
Center pillar upper finisher
3.
Front body side welt
4.
Front pillar finisher
5.
Dash side finisher
6.
Front kicking plate
7.
Center pillar lower finisher
8.
Rear kicking plate
9.
Rear pillar finisher
Clip
Pawl
Metal clip
AWJIA0726ZZ
AWJIA0728ZZ
INT-20
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
3. Remove the front pillar finisher clips (B) using a suitable tool (A).
INSTALLATION
1. Install the front pillar finisher clips (A) to the front pillar finisher by
inserting clip end and rotating 90 degrees in either direction.
2. Install the front pillar finisher to the front pillar.
CAUTION:
When installing front pillar finisher, check that all clips are securely pressed into body panel holes.
KICKING PLATE INNER
KICKING PLATE INNER : Removal and Installation
INFOID:0000000009269472
FRONT KICKING PLATE
Removal
1. Release front kicking plate pawls using a suitable tool (A) and
remove front kicking plate as shown.
CAUTION:
Apply protective tape (B) to the body as shown before
releasing the pawls on the outer ends.
: Pawl
ALJIA0736ZZ
AWJIA0729ZZ
AWJIA0730ZZ
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Installation
Installation is in the reverse order of removal.
CAUTION:
When installing rear kicking plate, make sure that metal clips are securely pressed in body panel
holes.
REAR KICKING PLATE
Removal
1. Remove rear seat cushion. Refer to
SE-23, "Removal and Installation - Seat Cushion Assembly"
2. Remove rear kicking plate clip (A).
3. Lift rear end of rear kicking plate to disengage rear kicking plate
metal clips, then rotate front end of rear kicking plate to disen-
gage rear kicking plate pawls and remove rear kicking plate.
: Metal clip
: Pawl
Installation
Installation is in the reverse order of removal.
CAUTION:
When installing rear kicking plate, make sure that metal clips are securely pressed in body panel
holes.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000009269473
REMOVAL
1. Remove front kicking plate. Refer to
INT-20, "KICKING PLATE INNER : Removal and Installation"
.
JMJIA6040ZZ
AWJIA0731ZZ
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2. Lift up rear end of dash side finisher to disengage metal clip.
: Metal clip
3. Pull back dash side finisher to disengage dash side finisher
metal clip and remove dash side finisher.
: Metal clip
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
When installing dash side finisher, make sure that all metal clips are securely pressed into body panel
holes.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000009269474
CAUTION:
Do not excessively pull or stretch body side welts.
FRONT BODY SIDE WELT
Removal
1. Remove dash side finisher. Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installation"
.
2. Remove center pillar lower finisher. Refer to
INT-23, "CENTER PILLAR LOWER FINISHER : Removal
3. Remove front body side welt.
Installation
Installation is in the reverse order of removal.
REAR BODY SIDE WELT
Removal
1. Remove center pillar lower finisher. Refer to
INT-23, "CENTER PILLAR LOWER FINISHER : Removal
2. Remove rear body side welt.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR LOWER FINISHER
JMJIA6043ZZ
JMJIA6044ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст