Nissan Versa Sedan. Manual — part 681
SE-50
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR SEAT
Disassembly and Assembly - Seat Cushion
INFOID:0000000009268538
SEAT CUSHION
Disassembly
1. Remove the seat cushion assembly. Refer to
SE-23, "Removal and Installation - Seat Cushion Assembly"
.
2. Remove the hog rings on the bottom side of seat cushion.
3. Remove the hog rings on the top side of seat cushion and separate the seat cushion trim from the seat
cushion pad.
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Make sure hog rings are correctly fastened around both the seat cushion trim and seat cushion pad
wires.
• Replace any deformed or damaged hog rings.
• Make sure any old hog ring pieces are removed from seat.
NOTE:
13. Seat cushion pad
14. Seat cushion hook
15. Seatback hinge assembly
16. Rear seat bolster (LH)
17. Seatback pad (LH)
18. Seatback trim (LH)
19. Seatback latch assembly (LH)
20. Seatback striker
21. Rear seatback frame (LH)
22. Rear seatback assembly (LH)
A.
Seatback hinge finisher clips
ALJIA0984ZZ
1.
Seat cushion pad
2.
Seat cushion trim
A.
Hog rings
REAR SEAT
SE-51
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
• Install new hog rings on the seat cushion trim in original positions.
• Use only one hog ring in each designated location.
Disassembly and Assembly - Fixed Seatback
INFOID:0000000009268539
FIXED SEATBACK
Disassembly
1. Remove the rear seatback assembly. Refer to
SE-23, "Removal and Installation - Fixed Seatback"
2. Release locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing the headrest holder, check its
orientation (front/rear and right/left)
3. Remove the hog rings from the back side of the rear seatback assembly.
PIIB3356J
ALJIA0983ZZ
1.
Seatback pad
2.
Seatback trim
A.
Hog rings
PIIB4084J
SE-52
< UNIT DISASSEMBLY AND ASSEMBLY >
REAR SEAT
4. Remove the hog rings from the front side of the rear seatback assembly and separate the seatback trim
from the seatback pad.
NOTE:
Remove all pieces of hog rings and discard them.
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.
• Replace any deformed or damaged hog rings.
• Make sure any old hog ring pieces are removed from seat.
NOTE:
• Install new hog rings on the seatback trim in original positions.
• Use only one hog ring in each designated location.
Disassembly and Assembly - Split Seatback
INFOID:0000000009268540
DISASSEMBLY
1. Remove the rear seatback assembly. Refer to
SE-23, "Removal and Installation - 60:40 Split Seatback"
.
2. Rotate the seatback latch release knob (1) counterclockwise
and remove.
3. Release the J-hook retainer (C), the clips (A), and unzip the
seatback trim zippers (B).
PIIB3356J
AWJIA0904ZZ
AWJIA0905ZZ
REAR SEAT
SE-53
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
4. Reach up through the seatback trim and release locks as shown
and remove the headrest holders.
CAUTION:
Before removing/installing the headrest holder, check its
orientation (front/rear and right/left).
5. Remove the seatback trim and seatback pad from the seatback frame.
6. Separate the seatback trim from the seatback pad.
a. Remove the hog rings and separate the seatback trim from the
seatback pad.
: Hog ring
(1) Seatback trim (LH)
(2) Seatback trim (RH)
NOTE:
Remove all pieces of hog rings and discard them.
7. Remove the bolts (A) and the rear seatback latch assembly (1)
from the seatback frame (2).
Assembly
Assembly is in the reverse order of disassembly.
CAUTION:
• Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.
• Replace any deformed or damaged hog rings.
• Make sure any old hog ring pieces are removed from seat.
NOTE:
PIIB4084J
ALJIA0986ZZ
ALJIA0700ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст