Nissan Versa Sedan. Manual — part 213
DLK-170
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
7. While pulling outside handle, remove door key cylinder assem-
bly (LH side) or outside handle escutcheon (RH side).
8. While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9. Remove front gasket (1) and rear gasket (2).
: Front
10. Slide outside handle bracket toward rear of vehicle to remove.
: Front
11. Disconnect outside handle cable (1) from outside handle bracket
(2) as shown.
JMKIA0560ZZ
JMKIA0524ZZ
JMKIA5889ZZ
JMKIA5890ZZ
JMKIA5891ZZ
FRONT DOOR LOCK
DLK-171
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check rear door hinge rotating point for poor lubrication. if necessary, apply a suitable multi-pur-
pose grease.
• Check that door lock cables are normally engaged with inside handle and outside handle.
• After installation, check door open/close, and lock/unlock operation.
DLK-172
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
REAR DOOR LOCK
Exploded View
INFOID:0000000009268871
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009268872
REMOVAL
1. Remove inside handle. Refer to
DLK-173, "INSIDE HANDLE : Removal and Installation"
.
2. Remove outside handle. Refer to
DLK-174, "OUTSIDE HANDLE : Removal and Installation"
.
3. Remove bolt (A) from the front door glass channel rear (1).
4. Disconnect the harness connector from door lock actuator.
5. Remove door lock assembly bolts and door lock assembly.
1.
Outside handle escutcheon
2.
Rear gasket
3.
Outside handle bracket
4.
Bolt
5.
Door lock assembly
6.
Inside handle
7.
Outside handle
8.
Front gasket
9.
Clip
Pawl
Front
JMKIA8161GB
JMKIA8086ZZ
REAR DOOR LOCK
DLK-173
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock assembly bolt. Always replace it with a new one when it is removed.
• After installation, check door open/close, lock/unlock operation.
• Check door lock cable is properly engaged with outside handle bracket.
• Check door lock assembly for poor lubrication. Apply a suit-
able multi-purpose grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009268873
REMOVAL
1. Remove rear door finisher. Refer to
INT-17, "Removal and Installation"
.
2. Remove upper side of sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape remain on the sealing screen, if the sealing screen
is reused.
3. Disengage lock knob cable (2) and inside handle cable (3) from
cable clip (1).
4. Remove inside handle bolt.
5. Disengage inside handle (1) from door panel (2) by sliding
toward vehicle rear and then separating.
: Pawl
: Front
JMKIA8087ZZ
JMKIA5704ZZ
JMKIA8079ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст