Nissan Versa Sedan. Manual — part 212
DLK-166
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD LOCK
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
.
Inspection
INFOID:0000000009268866
NOTE:
If the hood lock cable is bent or deformed, replace it.
1. Check that secondary latch (1) is properly engaged with second-
ary striker (2) with hood’s own weight.
2. Check that primary latch (1) is securely engaged with primary
striker (2) when hood is dropped with hood’s own weight from
approximately 200 mm (7.9 in) height.
3. While operating the hood lock/fuel filler door release handle assembly, carefully check that the front end of
hood is raised by approximately 20.0 mm (0.79 in). Also check that hood lock/fuel filler door release han-
dle assembly returns to the original position.
4. Check that hood lock/fuel filler door release handle assembly operates at 49 N (5.0 kg-f, 11.0 lb-f) or
below.
5. Install so that static the hood is 300 – 490 N (31.0 – 50.0 kg-f, 67.4 – 110.2 lb-f).
NOTE:
• Do not exert vertical force on right side and left side of hood lock.
• Do not press simultaneously both sides.
6. Check the hood lock lubrication condition. If necessary, apply a suitable multi-purpose grease to second-
ary latch (1) and hood lock assembly (2).
JMKIA7993ZZ
JMKIA7994ZZ
JMKIA8000ZZ
FRONT DOOR LOCK
DLK-167
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR LOCK
Exploded View
INFOID:0000000009268867
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009268868
REMOVAL
1. Remove inside handle. Refer to
DLK-168, "INSIDE HANDLE : Removal and Installation"
.
2. Remove outside handle. Refer to
DLK-169, "OUTSIDE HANDLE : Removal and Installation"
.
3. Disconnect the harness connector from the door lock actuator.
4. Remove front door lower sash (rear). Refer to
5. Remove door lock assembly bolts and door lock assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door lock assembly bolt. Always replace it with a new one when it is removed.
• After installation, check door open/close, lock/unlock operation.
• Check door lock cable is properly engaged with outside handle bracket.
1.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
2.
Rear gasket
3.
Outside handle bracket
4.
Bolt
5.
Door key cylinder rod (driver side)
6.
Door lock assembly
7.
Inside handle
8.
Outside handle
9.
Front gasket
10. Clip
Pawl
Front
JMKIA8160GB
DLK-168
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
• Check door lock assembly for poor lubrication. Apply a suit-
able multi-purpose grease to door lock if necessary.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009268869
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Remove upper side of sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape remain on the sealing screen, if the sealing screen
is reused.
3. Disengage lock knob cable (2) and inside handle cable (3) from
clip (1).
4. Remove inside handle bolt.
5. Disengage inside handle (1) from door panel (2) by sliding
toward vehicle rear and separating.
: Pawl
: Front
6. Disengage inside handle cable (3) and lock knob cable (2), and
remove inside handle (1).
JMKIA8077ZZ
JMKIA8078ZZ
JMKIA8079ZZ
JMKIA5885ZZ
FRONT DOOR LOCK
DLK-169
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check door open/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009268870
REMOVAL
1. Fully close the front door glass.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
3. Remove sealing screen.
NOTE:
Cut the butyl tape so that some parts of the butyl tape remain on the sealing screen, if the sealing screen
is reused.
4. For drivers side only, open rod holder (1) by pulling downward
and separate key rod (3) from door lock assembly (2).
5. Disengage outside handle cable (1) from cable clip (2).
: Front
6. Remove door side grommet (1), and loosen bolt from grommet
hole (2).
JMKIA8080ZZ
JMKIA8081ZZ
JMKIA5888ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст