Nissan Primera P11. Manual — part 67
REMOVAL
After removing moldings, remove glass using piano wire or
power cutting tool and inflatable pump bag.
WARNING:
●
Be careful not to scratch the glass when removing.
●
Do not set or stand the glass on its edges. Small chips
may develop into cracks.
INSTALLATION
●
Use a genuine Nissan Urethane Adhesive Kit or equivalent
and follow the instructions furnished with it.
●
While the urethane adhesive is curing, open a door window.
This will prevent the glass from being forced out by passen-
ger compartment air pressure when a door is closed.
●
The molding must be installed securely so that it is in posi-
tion and leaves no gap.
●
Inform the customer that the vehicle should remain station-
ary until urethane adhesive has completed cured (preferably
24 hours). Curing time varies with temperature and humidity.
WARNING:
●
Keep heat and open flames away as primers and adhesive
are flameable.
●
The materials contained in the kit are harmful if swallowed,
and may irritate skin and eyes.
●
Use in an open , well ventilated location. Avoid breathing the
vapors. They can be harmful if inhaled. If affected by vapor
inhalation, immediately move to an area with fresh air.
●
Driving the vehicle before the urethane adhesive has com-
pletely cured may affect the performance of the windshield in
case of an accident.
CAUTION
●
Do not use an adhesive which is past its usable term. Shelf
life of this product is limited to six months after the date of
manufacture. Carefully adhere to expiration or manufacture
date printed on the box.
●
Keep primers and adhesive in a cool, dry place. Ideally, they
should be stored in a refrigerator.
●
Do not leave primers and adhesive cartridge unattended with
their caps open or off.
●
The vehicle should not be driven for at least 24 hours or until
the urethane adhesive has completely cured. Curing times
varies depending on temperature and humidities. The curing
time will increase under higher temperatures lower humidi-
ties.
SBF034B
Cutting sealant
Glass
SBT472
Windshield glass
Interior auto glass
cut-out knife kit
SBT473
Windshield
glass
Inflatable
pump bag
WINDSHIELD AND WINDOWS
BT-53
Windshield and Rear Window
REPAIRING WATER LEAKS FOR WINDSHIELD
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between caulking material and body or glass, determine the extent of leakage. This
can be determined by applying water while pushing glass outward.
To stop the leak, apply primer (if necessary) and then sealant to the leak point.
YBT033
Body side
SBF017A
Glass side
YBT034
Windshield
Install spacer to panel
Cowl top
Glass
Spacer
455.4 mm (17.93 in)
Install dam rubber.
Windshield and
rear window
8 (0.31)
Vehicle center
joint portion
Apply sealant evenly
12
-
1
5
(0.47
-
0.59)
Dam rubber
Glass
Unit: mm (in)
7 - 8 (0.28 - 0.31)
8 (0.31)
8 (0.31)
Install molding fastener.
When installing it, heat body panel and fastener to
approx. 30 to 40°C (86 to 104°F).
Windshield
Upper & side molding fasteners
Fastener
Panel
Double-faced
adhesive tape
Rear window
WINDSHIELD AND WINDOWS
BT-54
Side Window
Primer portion
Sealing portion and installation
NBF283
Body side
.
A
A
B
B
Primer
portion
A-A
B-B
Primer
portion
Primer
portion
Glass side
A
A
Window glass
B
Primer portion
Primer portion
A-A
Glass
B-B
Glass
Primer
portion
B
D
D
A
A
B
B
Clip
(bonded on
glass)
C-C
Glass
Clip
(bonded on
glass)
Glass
D-D
More than
7 (0.28)
More than
8 (0.32)
Glass
Molding
Apply sealant evenly
Unit: mm (in)
More than
7 (0.28)
More than
8 (0.32)
Glass
NBF281
WINDSHIELD AND WINDOWS
BT-55
Back Door Window
●
Construction and removal/reinstallation method of back door window are basically the same as those of
windshield.
5-door hatchback
●
For details of moldings, refer to “EXTERIOR”, BT-31.
YBT035
Primer portion (Body side)
Primer
Primer
30 (1.18)
Primer
Sealant quantity
12 - 15
(0.47 - 0.59)
7 - 8
(0.28 - 0.31)
33 (1.30)
33 (1.30)
8.75
(0.3445)
18.4
(0.724)
41.2
(1.622)
28 (1.10) 41 (1.61) 33 (1.30)
400 (15.75)
Sealant portion (Body side)
Primer portion (Glass side)
Dam rubber portion (Glass side)
Back door molding
Dam rubber
Primer
Back door molding
Back door molding
Primer
Back door molding
Primer
Unit: mm (in)
WINDSHIELD AND WINDOWS
BT-56
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст