Nissan Pathfinder. Manual — part 671
QUARTER WINDOW GLASS
GW-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Unit : mm (in)
• Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
• Check gap along bottom to confirm that glass does not contact sheet metal.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the glass in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time will increase
under lower temperatures and lower humidity.
REPAIRING WATER LEAKS FOR QUARTER WINDOW GLASS
• Leaks can be repaired without removing or reinstalling glass.
• If water is leaking between urethane adhesive material and body or glass, determine the extent of leakage.
• This can be done by applying water to the quarter window glass area while pushing glass outward.
• To stop leak, apply primer (if necessary) and then urethane adhesive to the leak point.
1. Quarter window glass molding
2. Quarter window glass
3. Adhesive
E. 7.0
± 2.0 (0.28 ± 0.08 in)
F. 12.0
± 2.0 (0.47 ± 0.08)
G.
10.0 (0.39)
AWKIA2591ZZ
GW-26
< REMOVAL AND INSTALLATION >
PANORAMIC ROOF GLASS
PANORAMIC ROOF GLASS
Exploded View
INFOID:0000000009176096
Removal and Installation
INFOID:0000000009176097
REMOVAL
1. Remove the headlining. Refer to
INT-27, "Removal and Installation"
.
2. Remove the sunshade. Refer to
RF-58, "REAR SUNSHADE UNIT : Removal and Installation"
3. Remove the panoramic roof glass using piano wire or power cutting tool and an inflatable pump bag.
WARNING:
When cutting the panoramic roof glass from the vehicle, always wear safety glasses and heavy gloves
to help prevent glass splinters from entering your eyes or cutting your hands.
CAUTION:
• Apply protective tape around the panoramic roof glass to protect the painted surface from damage.
• Be careful not to scratch the glass when removing.
• Do not set or stand the panoramic roof glass on its edge. Small chips may develop into cracks.
INSTALLATION
Installation is in the reverse order of removal.
• Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
• While the urethane adhesive is curing, open a window. This will prevent the panoramic roof glass from being
forced out by passenger compartment air pressure when a door is closed.
• The rubber seal must be installed securely so that it is in position and leaves no gap.
• Inform customer that the vehicle should remain stationary until the urethane adhesive has completely cured
(preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
1.
Panoramic roof glass
2.
Roof panel
3.
Moonroof assembly
Front
AWKIA2593ZZ
PANORAMIC ROOF GLASS
GW-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
• Keep heat and open flames away as primers and adhesives are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
if affected by vapor inhalation, immediately move to area with fresh air.
• Driving the vehicle before urethane adhesive has completely cured may affect the performance of
the panoramic roof glass in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesives in a cool dry place. ideally they should be stored in a refrigerator.
• Do not leave primers and adhesive cartridge unattended with their caps off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time depends on temperature and humidity. The curing time will increase under lower
temperature and lower humidity.
Unit: mm (in)
REPAIRING WATER LEAKS FOR PANORAMIC ROOF GLASS
• Leaks can be repaired without removing and reinstalling glass.
• If water is leaking between the urethane adhesive material and body or glass, determine the extent of leak-
age.
• This can be done by applying water to the glass area while pushing glass outward.
• To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
1.
Panoramic roof glass
2.
Roof
3.
Adhesive
C.
5.4
± 1.5 (0.21 ± 0.06)
D.
2.8 +1.5, -0.5 (0.11 +0.06, -0.02)
E.
12.0 (0.47)
Front
ALKIA3217ZZ
GW-28
< REMOVAL AND INSTALLATION >
BACK DOOR WINDOW GLASS
BACK DOOR WINDOW GLASS
Exploded View
INFOID:0000000009176098
Removal and Installation
INFOID:0000000009176099
REMOVAL
1. Remove back door finishers (upper, lower and side). Refer to
INT-35, "BACK DOOR SIDE FINISHER :
.
2. Remove the rear spoiler. Refer to
EXT-41, "Removal and Installation"
3. Disconnect the harness connectors from back door window glass defogger.
4. Remove the rear wiper arm. Refer to
WW-67, "Removal and Installation"
1.
Rear spoiler
2.
Back door assembly
3.
Rear wiper arm
4.
Back door window glass
5.
High-mounted stop lamp
ALKIA2947ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст