Nissan Pathfinder. Manual — part 670
REAR DOOR GLASS AND REGULATOR
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
4. Operate the rear power window switch to raise/lower the rear
door glass until the rear door regulator to glass bolts (A) can be
seen and remove.
5. Raise the rear door glass and hold in place with suitable tool or approximately two inches of masking tape.
6. Remove the bolts (B) from the rear door glass regulator (1) and
guide channel nuts (A).
7. Disconnect the harness connector from the rear door glass reg-
ulator motor (1).
8. Remove rear door regulator to glass bolts (B) and the rear door
glass regulator.
9. Remove power window motor from rear door glass regulator (if necessary). Refer to
Inspection after removal
Check the rear door glass regulator for the following items:
• Gear wear
• Rear door glass regulator deformation
• Spring damage
• Grease condition for each sliding part
If a malfunction is detected, replace or grease it.
Installation
1. Install power window motor to rear door glass regulator (if necessary). Refer to
.
ALKIA3220ZZ
ALKIA2364ZZ
ALKIA2365ZZ
GW-22
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS AND REGULATOR
2. Connect the harness connector to the rear door glass regulator,
then install the rear door glass regulator and guide channel and
secure with nuts (A) and bolts (B).
3. Install the rear door glass from outside to ensure that it is in both
the rear door front and rear glass channels. Install the rear door
glass to regulator bolts (A).
4. Reposition the vapor barrier.
5. Install the rear door finisher. Refer to
INT-17, "Removal and Installation"
Regulator and guide
channel nuts and bolts
: 7.0 N·m (0.7 kg-m, 62 in-lb)
ALKIA3221ZZ
Rear door regulator to
glass bolts
: 7.0 N·m (0.70 kg-m, 62 in-lb)
ALKIA3220ZZ
REAR POWER WINDOW MOTOR
GW-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR POWER WINDOW MOTOR
Removal and Installation
INFOID:0000000009723958
REMOVAL
1. Remove rear door glass regulator. Refer to
GW-19, "Removal and Installation"
2. Remove screws (A) and rear power window motor (1) from rear
door glass regulator (2).
INSTALLATION
Installation is in the reverse order of removal.
ALKIA3215ZZ
GW-24
< REMOVAL AND INSTALLATION >
QUARTER WINDOW GLASS
QUARTER WINDOW GLASS
Exploded View
INFOID:0000000009176094
Removal and Installation
INFOID:0000000009176095
REMOVAL
1. Remove the luggage side lower finisher. Refer to
INT-31, "LUGGAGE SIDE LOWER FINISHER :
.
2. Remove the luggage side upper finisher. Refer to
INT-32, "LUGGAGE SIDE UPPER FINISHER :
.
3. Remove quarter glass from the inside of vehicle using a suitable tool.
WARNING:
When cutting the quarter window from the vehicle, always wear safety glasses and heavy gloves
to help prevent glass splinters from entering your eyes or cutting your hands.
CAUTION:
• Apply protective tape around the quarter glass to protect the painted surface.
• Be careful not to scratch the quarter window glass when removing.
• Do not set or stand the quarter window glass on its edge. Small chips may develop into cracks.
INSTALLATION
Installation is in the reverse order of removal.
• Install the quarter glass from outside the vehicle to ensure that it is even around the top, bottom and sides of
the opening.
1. Body side outer panel
2. Adhesive and primer area
3. Quarter window glass
A. Clip
AWKIA2590ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст