Nissan Pathfinder. Manual — part 379
DLK-282
< REMOVAL AND INSTALLATION >
FRONT FENDER
Use care when removing the front fender. The front fender baffle foam adheres the front fender to
the body side outer. Carefully release the baffle foam or damage to the front fender may occur.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation apply touch up paint (body color) to the head of front fender bolts.
• After installation, adjust the following components as necessary:
- Hood assembly: Refer to
DLK-276, "HOOD ASSEMBLY : Adjustment"
.
- Front door: Refer to
FRONT DOOR
DLK-283
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR
Exploded View
INFOID:0000000009175869
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009175870
CAUTION:
• Use two people when removing or installing the front door due to its heavy weight.
• When removing and installing front door assembly, support front door with a suitable tool.
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Disconnect the harness connectors from the front door.
3. Remove front door harness grommet, then harness from the front door.
4. Remove front door check link bolt (body side).
5. Remove front door hinge nuts (door side) and front door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent where necessary.
• After installation, check front door open/close and lock/unlock operation.
• After installation, perform the front door adjustment procedure. Refer to
1.
Front door panel
2.
Grommet
3.
Front door striker
4.
Bumper rubber
5.
Door check link
6.
Front door lower hinge
7.
Front door upper hinge
AWKIA2623ZZ
DLK-284
< REMOVAL AND INSTALLATION >
FRONT DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000009175871
Adjustment
Check the clearance and surface height between front door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
1. Remove front fender. Refer to
DLK-281, "FRONT FENDER : Removal and Installation"
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Front door upper hinge
6.
Front door lower hinge
7.
Door striker
F.
Front door striker bolts
AWKIA2624ZZ
Portion
Section
Measurement
Standard
Front fender - Front door
A – A
Clearance
4.0
± 1.0 (0.16 ± 0.04)
Surface height
± 1.0 (± 0.04)
Front door - Rear door
B – B
Clearance
4.3
± 1.0 (0.17 ± 0.04)
Surface height
± 1.0 (± 0.04)
Rear door - Body side outer
C – C
Clearance
3.7
± 1.0 (0.15 ± 0.04)
Surface height
± 1.0 (± 0.04)
FRONT DOOR
DLK-285
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Loosen front door hinge nuts (door side).
3. Adjust the surface height of front door according to the specifications provided.
4. Temporarily tighten front door hinge nuts (door side).
5. Loosen front door hinge bolts (body side).
6. Raise front door at rear end to adjust clearance of the front door according to the specifications provided.
7. After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• Check door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After adjusting, apply touch-up paint (body color) to the head of front door hinge bolts and nuts.
8. Install front fender. Refer to refer to
DLK-281, "FRONT FENDER : Removal and Installation"
.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000009175872
REMOVAL
Remove bolts and front door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse front door striker bolts.
• After installation, check front door open/close operation. If necessary, adjust the front door striker.
Refer to
DLK-285, "DOOR STRIKER : Adjustment"
DOOR STRIKER : Adjustment
INFOID:0000000009726874
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts
2. Adjust door striker so that it becomes parallel with front door lock
insertion direction.
3. Tighten door striker bolts to specification. Refer to
.
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000009175873
REMOVAL
1. Remove front fender. Refer to
DLK-281, "FRONT FENDER : Removal and Installation"
2. Remove front door assembly. Refer to
DLK-283, "DOOR ASSEMBLY : Removal and Installation"
.
3. Remove front door hinge bolts (body side) and front door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent to the hinge mating surface.
• After installation, check front door open/close and lock/unlock operation.
PIIB2804J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст