Nissan Pathfinder. Manual — part 380
DLK-286
< REMOVAL AND INSTALLATION >
FRONT DOOR
• Check door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After installation, perform the front door adjustment procedure. Refer to
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000009175874
REMOVAL
1. Fully close the front door window.
2. Remove front door speaker. Refer to
AV-50, "Removal and Installation"
AV-373, "Removal and Installation"
(MID
AUDIO WITH BOSE) or
AV-619, "Removal and Installation"
(PREMIUM AUDIO WITH NAVIGATION).
3. Remove door check link bolt from body.
4. Remove door check link nuts on door assembly.
5. Remove door check link through the hole in door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check front door open/close and lock/unlock operation.
• Check door check link rotating point for poor lubrication. If necessary, apply a suitable multi-pur-
pose grease.
REAR DOOR
DLK-287
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR
Exploded View
INFOID:0000000009175875
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000009175876
CAUTION:
• Use two people when removing or installing the rear door due to its heavy weight.
• When removing and installing rear door assembly, support rear door using a suitable tool.
REMOVAL
1. Remove rear door finisher. Refer to
DLK-287, "DOOR ASSEMBLY : Removal and Installation"
.
2. Disconnect the harness connectors from rear door.
3. Remove harness grommet from rear door, then pull out rear door harness from the rear door.
4. Remove rear door check link bolt (body side).
5. Remove rear door hinge nuts (door side) and rear door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent where necessary.
• After installation, check rear door open/close and lock/unlock operation.
• After installation, perform the rear door adjustment procedure. Refer to
.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
Bumper rubber
5.
Door check link
6.
Rear door lower hinge
7.
Rear door upper hinge
AWKIA2605ZZ
DLK-288
< REMOVAL AND INSTALLATION >
REAR DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000009175877
Check the clearance and surface height between rear door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dures.
Unit: mm (in)
1. Remove center pillar lower finisher. Refer to
INT-21, "CENTER PILLAR LOWER FINISHER : Removal
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
Rear door upper hinge
7.
Rear door lower hinge
F.
Door striker bolts
AWKIA2628ZZ
Portion
Section
Measurement
Standard
Front fender - Front door
A – A
Clearance
4.0
± 1.0 (0.16 ± 0.04)
Surface height
± 1.0 (± 0.04)
Front door - Rear door
B – B
Clearance
4.3
± 1.0 (0.17 ± 0.04)
Surface height
± 1.0 (± 0.04)
Rear door - Body side outer
C – C
Clearance
3.7
± 1.0 (0.15 ± 0.04)
Surface height
± 1.0 (± 0.04)
REAR DOOR
DLK-289
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Loosen rear door hinge nuts (door side).
3. Adjust the surface height of rear door according to specifications provided.
4. Temporarily tighten rear door hinge nuts (door side).
5. Loosen rear door hinge nuts and bolts (body side).
6. Raise rear door at rear end to adjust clearance of rear door according to the specifications provided.
7. After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• Check rear door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-pur-
pose grease.
• After adjusting, apply touch-up paint (body color) to the head of rear door hinge bolts and nuts.
8. Install center pillar lower finisher. Refer to
INT-21, "CENTER PILLAR LOWER FINISHER : Removal and
.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000009175878
REMOVAL
Remove bolts and rear door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse rear door striker bolts.
• After installation, check rear door open/close operation. If necessary, adjust the door striker. Refer to
DLK-289, "DOOR STRIKER : Adjustment"
DOOR STRIKER : Adjustment
INFOID:0000000009729241
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts
2. Adjust door striker so that it becomes parallel with front door lock
insertion direction.
3. Tighten door striker bolts to specification. Refer to
.
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000009175879
REMOVAL
1. Remove rear door assembly. Refer to
DLK-287, "DOOR ASSEMBLY : Removal and Installation"
2. Remove center pillar lower finisher. Refer to
INT-21, "CENTER PILLAR LOWER FINISHER : Removal
3. Remove rear door hinge bolts and nuts and rear door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the hinge mating surface.
PIIB2804J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст