Nissan Pathfinder. Manual — part 631
FAX-12
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT BOOT
12. Remove boot bands.
13. Remove boot from joint sub-assembly.
14. Screw sliding hammer or suitable tool (A) 30 mm (1.18 in) or
more into threaded part of joint sub-assembly. Support drive
shaft with one hand and pull out joint sub-assembly with a slid-
ing hammer or suitable tool from housing assembly.
CAUTION:
• Align sliding hammer or suitable tool and drive shaft and
remove joint sub-assembly by pulling directly.
• If joint sub-assembly cannot be removed after five or
more unsuccessful attempts, replace the entire drive shaft
assembly.
15. Remove circular clip (1) from housing assembly.
16. Remove boot from housing assembly.
17. Inspect the components. Refer to
INSTALLATION
1. Clean the old grease on joint sub-assembly with paper shop cloth.
2. Fill serration slot joint sub-assembly with NISSAN genuine grease or equivalent.
CAUTION:
After applying grease, use a paper shop cloth to wipe off old grease that has oozed out.
3. Install boot and boot bands to housing assembly.
CAUTION:
• Wrap serration on housing assembly with tape to protect the boot from damage.
• Do not reuse boot and boot band.
4. Remove the tape wrapped around the serration on housing assembly.
5. Position the circular clip on groove at the housing assembly edge.
CAUTION:
Do not reuse circular clip.
6. Align both center axles of the housing assembly edge and joint sub-assembly. Install housing assembly
with joint sub-assembly holding circular clip.
7. Install joint sub-assembly (1) to housing assembly using suitable
tool.
CAUTION:
Confirm that joint sub-assembly is correctly engaged while
rotating drive housing assembly.
8. Apply the specified amount of grease into the large diameter
side opening of the boot.
JPDIF0258ZZ
JPDIF0007ZZ
Grease amount
: Refer to
.
JPDIF0011ZZ
FRONT DRIVE SHAFT BOOT
FAX-13
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
9. Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” mark) on the housing assembly or joint sub-assem-
bly, boot may come off. Remove all grease from the boot
mounting surface.
10. Make sure boot installation length (L) is the specified length.
Insert a suitable tool into the large end of boot. Bleed air from
boot to prevent boot deformation.
CAUTION:
• Boot may break if boot installation length is not within standard value.
• Be careful that suitable tool does not contact inside surface of boot.
11. Install new large and small boot bands securely using Tool.
CAUTION:
Do not reuse boot band.
NOTE:
Secure boot band so that dimension (M) meets the specification
as shown.
12. Secure joint sub-assembly and housing assembly. Make sure
that they are in the correct position when rotating boot. Reinstall
them using boot bands when boot installation positions become
incorrect.
CAUTION:
Do not reuse boot band.
13. Clean the mating surface of the wheel hub lock nut and the
wheel hub and bearing.
CAUTION:
Do not apply lubricating oil to these mating surfaces.
14. Clean the mating surface of the drive shaft (A) and the wheel
hub and bearing.
15. Insert drive shaft to wheel hub and bearing.
16. Temporarily install the wheel hub lock nut.
Boot installation
length (L)
: Refer to
.
Tool number : KV40107300 ( — )
JPDIF0222ZZ
RAC1133D
Dimension (M)
DSF0047D
JPDIG0122ZZ
FAX-14
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT BOOT
CAUTION:
Do not reuse the wheel hub lock nut.
17. Install the front strut to the steering knuckle. Tighten the lower strut nuts to the specification. Refer to
18. Align the marks on the disc brake rotor and on the wheel hub and bearing. Install the disc brake rotor.
19. Install caliper assembly to steering knuckle. Refer to
BR-36, "BRAKE CALIPER ASSEMBLY : Removal
20. Install wheel sensor to steering knuckle. Refer to
BRC-118, "Exploded View - Front Wheel Sensor"
.
21. Tighten the wheel hub lock nut to the specified torque. Refer to
.
CAUTION:
Do not use a power tool to tighten the wheel hub lock nut.
22. Install the nut retainer.
23. Install a new cotter pin. Refer to
.
CAUTION:
• Do not reuse cotter pin.
• Bend cotter pin securely to prevent any looseness.
24. Install the front wheel and tire. Refer to
TRANSAXLE SIDE
TRANSAXLE SIDE : Removal and Installation
INFOID:0000000009177845
NOTE:
Remove boot after removing drive shaft. Refer to
FAX-15, "Removal and Installation (LH)"
Inspection
INFOID:0000000009177846
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there
is a non-standard condition.
SDIA1190J
FRONT DRIVE SHAFT
FAX-15
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Exploded View (LH)
INFOID:0000000009177847
Removal and Installation (LH)
INFOID:0000000009177848
REMOVAL
1. Remove the front wheel and tire using power tool. Refer to
2. Remove the brake caliper torque member bolts, leaving brake hose attached. Position the caliper aside
with wire. Refer to
BR-36, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
Do not depress brake pedal while brake caliper is removed.
3. Put alignment marks on disc brake rotor and on the wheel hub
and bearing. Remove the disc brake rotor.
CAUTION:
Do not drop the disc brake rotor.
4. Remove wheel sensor bolt (A) and position wheel sensor aside.
BRC-118, "Exploded View - Front Wheel Sensor"
CAUTION:
Do not pull on wheel sensor harness.
5. Remove cotter pin.
1.
Drive shaft
2.
Nut retainer
3.
Cotter pin
AWDIA1024ZZ
SDIA1480E
ALDIA0287ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст