Nissan Pathfinder. Manual — part 630
FAX-8
< REMOVAL AND INSTALLATION >
FRONT WHEEL HUB
REMOVAL AND INSTALLATION
FRONT WHEEL HUB
Exploded View
INFOID:0000000009177841
Removal and Installation
INFOID:0000000009177842
REMOVAL
1. Remove the front wheel and tire using power tool. Refer to
2. Remove the brake caliper torque member bolts, leaving the brake hose attached. Position the caliper
aside with wire. Refer to
BR-36, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
• Do not depress the brake pedal while the brake caliper is removed.
3. Put alignment marks on the disc brake rotor and on the wheel
hub and bearing. Remove the disc brake rotor.
CAUTION:
Do not drop the disc brake rotor.
1.
Cotter pin
2.
Nut retainer
3.
Disc brake rotor
4.
Wheel hub and bearing
5.
Wheel stud
6.
Splash guard
7.
Steering knuckle
Front
ALDIA0299GB
SDIA1480E
FRONT WHEEL HUB
FAX-9
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
4. Remove the wheel sensor bolt (A) and position the wheel sensor
aside. Refer to
BRC-118, "Exploded View - Front Wheel Sen-
.
CAUTION:
Do not pull on the wheel sensor harness.
5. Remove the cotter pin.
6. Remove the nut retainer.
7. Loosen the wheel hub lock nut from the drive shaft using power tool.
8. Using a piece of wood and a hammer, tap on the lock nut to dis-
engage the drive shaft from the wheel hub and bearing.
CAUTION:
• Do not place the drive shaft joint at an extreme angle. Be
careful not to over extend the slide joint.
• Do not allow the drive shaft to hang without support.
NOTE:
Use a suitable puller if drive shaft cannot be separated from the
wheel hub and bearing.
9. Remove the wheel hub lock nut.
10. Remove the wheel hub and bearing bolts using power tool.
11. Remove the splash guard and the wheel hub and bearing from the steering knuckle.
INSPECTION AFTER REMOVAL
Check components for deformation, cracks, and other damage. Replace if necessary.
Ball joint inspection
Check for boot breakage, axial looseness, and torque of transverse link ball joint and repair as necessary.
INSTALLATION
Installation is in the reverse order of the removal.
CAUTION:
• Do not apply lubricating oil to the mating surfaces.
• Do not reuse the wheel hub lock nut.
• Do not use a power tool to tighten the wheel hub lock nut.
• Do not reuse the cotter pin.
• Clean the mating surface of the wheel hub lock nut and the wheel hub and bearing.
• Clean the mating surface of the drive shaft and the wheel hub and bearing.
• Align the marks on the disc brake rotor and on the wheel hub and bearing.
ALDIA0287ZZ
JPDIG0070ZZ
FAX-10
< REMOVAL AND INSTALLATION >
FRONT DRIVE SHAFT BOOT
FRONT DRIVE SHAFT BOOT
Exploded View
INFOID:0000000009177843
LH
RH
1.
Circlip
2.
Dust shield
3.
Slide joint housing
4.
Snap ring
5.
Spider assembly
6.
Stopper ring
7.
Boot band
8.
Boot
9.
Shaft
10. Damper band
11. Damper
12. Boot band
13. Boot
14. Ball cage / Steel ball / Inner race assembly
15. Circlip
16. Joint sub-assembly
Front
AWDIA0896ZZ
1.
Joint sub-assembly
2.
Circular clip
3.
Boot band
4.
Boot
5.
Damper band (if equipped)
6.
Dynamic damper (if equipped)
7.
Housing assembly
8.
Circular clip
9.
Dust shield
10. Oil seal
11. Bearing retainer
12. Bearing
13. Snap ring
14. Dust shield
15. Collar
AWDIA1111ZZ
FRONT DRIVE SHAFT BOOT
FAX-11
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
WHEEL SIDE
WHEEL SIDE : Removal and Installation
INFOID:0000000009177844
REMOVAL
1. Remove front wheel and tire using power tool. Refer to
2. Remove brake caliper torque member bolts using power tool, leaving brake hose attached. Position the
caliper aside with wire. Refer to
BR-36, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Do not depress brake pedal while brake caliper is removed.
3. Put alignment marks on the disc brake rotor and on the wheel
hub and bearing. Remove the disc brake rotor.
CAUTION:
Do not drop the disc brake rotor.
4. Remove wheel sensor bolt (A) and position wheel sensor aside.
BRC-118, "Exploded View - Front Wheel Sensor"
CAUTION:
Do not pull on wheel sensor harness.
5. Remove the cotter pin from the drive shaft.
6. Remove the nut retainer.
7. Loosen the wheel hub lock nut using power tool.
8. Using a piece of wood and a hammer, tap on the wheel hub lock
nut to disengage the drive shaft from the wheel hub and bearing.
CAUTION:
• Do not place drive shaft joint at an extreme angle. Be
careful not to over extend slide joint.
• Do not allow drive shaft to hang without support.
NOTE:
Use suitable puller if the drive shaft cannot be separated from
the wheel hub and bearing.
9. Remove the wheel hub lock nut.
10. Remove the lower strut bolts and nuts using power tool. Separate the front strut from the steering knuckle.
11. Separate the drive shaft from the wheel hub and bearing.
16. Link shaft
17. Support bearing bracket
A:
Oil seal lip
Wheel side
Fill NISSAN Genuine grease or equivalent.
SDIA1480E
ALDIA0287ZZ
JPDIG0070ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст