Nissan Pathfinder. Manual — part 613
EXL-140
< PERIODIC MAINTENANCE >
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
Aiming Adjustment
INFOID:0000000009175402
NOTE:
Check the following conditions before performing the aiming adjustment.
• Keep all tires inflated to correct pressure.
• Place vehicle on level ground.
• See that vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and
tools). Have the driver or equivalent weight placed in driver seat.
• When performing adjustment, if necessary, cover the headlamps and opposite fog lamp.
1. Set the distance between the screen and the center of the fog
lamp lens as shown.
(1) Aiming screen or a matte white surface
(2) 7.62 m (25 ft)
(3) Floor to center of fog lamp lens
(4) Floor
2. Turn front fog lamps ON.
3. Access adjustment screw from underneath front bumper. Use a
suitable tool to adjust. Turn screw clockwise to raise pattern and
counterclockwise to lower pattern. Adjust front fog lamps using
adjusting screw so that the top edge of the high intensity zone is
100 mm (4 in) below the height of the fog lamp centers as
shown.
(1) Vertical center line of left fog lamp.
(2) Lamp center above ground.
(3) 100 mm (4 in) (0.76 deg) below lamp center above ground.
(4) Left fog lamp high intensity area.
(5) Vehicle center axis.
(6) Vertical center line of right fog lamp.
(7) Right fog lamp high intensity area.
ALLIA1058ZZ
LKIA0572E
AWLIA2199ZZ
FRONT COMBINATION LAMP
EXL-141
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000009175403
Removal and Installation
INFOID:0000000009175404
FRONT COMBINATION LAMP
Removal
1. Disconnect the battery negative terminal. Refer to
PG-90, "Removal and Installation"
2. Release the clips and pawls using a suitable tool and remove hoodledge finisher.
3. Release front under cover clips and remove front under cover.
4. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
5. Remove washer tank. Refer to
WW-54, "Removal and Installation"
6. Remove front combination lamp bolts.
7. Pull front combination lamp forward.
8. Disconnect the harness connectors from the front combination lamp.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installation, perform headlamp aiming adjustment. Refer to
EXL-138, "Aiming Adjustment Proce-
HALOGEN BULB (LOW BEAM)
WARNING:
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
• Do not leave the bulb out of the lamp reflector for a long time because dust, moisture, smoke, etc.
may affect the performance of the lamp.
Removal
1. Rotate low beam bulb counterclockwise and remove.
1.
Front combination lamp
A.
Bolt
AWLIA2192ZZ
EXL-142
< REMOVAL AND INSTALLATION >
FRONT COMBINATION LAMP
2. Disconnect the harness connector from the low beam bulb.
Installation
Installation is in the reverse order of removal.
HALOGEN BULB (HIGH BEAM)
WARNING:
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
• Do not leave the bulb out of the lamp reflector for a long time because dust, moisture, smoke, etc.
may affect the performance of the lamp.
Removal
1. Rotate high beam bulb counterclockwise and remove.
2. Disconnect the harness connector from the high beam bulb.
Installation
Installation is in the reverse order of removal.
PARKING LAMP BULB
WARNING:
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
• Do not leave the bulb out of the lamp reflector for a long time because dust, moisture, smoke, etc.
may affect the performance of the lamp.
Removal
1. Release the clips and pawls using a suitable tool and remove hoodledge finisher.
2. Remove washer tank. Refer to
WW-54, "Removal and Installation"
3. Rotate parking lamp socket counterclockwise and remove.
4. Remove parking lamp bulb from the bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing, be sure to install the bulb socket securely to ensure watertightness.
FRONT TURN SIGNAL LAMP BULB
WARNING:
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
• Do not leave the bulb out of the lamp reflector for a long time because dust, moisture, smoke, etc.
may affect the performance of the lamp.
Removal
1. Release the clips and pawls using a suitable tool and remove hoodledge finisher.
2. Rotate front turn signal lamp socket counterclockwise and remove.
3. Remove front turn signal lamp bulb from the bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing, be sure to install the bulb socket securely to ensure watertightness.
FRONT SIDE MARKER LAMP BULB
WARNING:
FRONT COMBINATION LAMP
EXL-143
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
CAUTION:
• Do not touch glass surface of the bulb with bare hands or allow oil or grease to get on it to prevent
damage to bulb.
• Do not leave the bulb out of the lamp reflector for a long time because dust, moisture, smoke, etc.
may affect the performance of the lamp.
Removal
1. Release the clips and pawls using a suitable tool and remove hoodledge finisher.
2. Remove washer tank. Refer to
WW-54, "Removal and Installation"
3. Rotate front side marker lamp socket counterclockwise and remove.
4. Remove front side marker lamp bulb from the bulb socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing, be sure to install the bulb socket securely to ensure watertightness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст