Nissan Pathfinder. Manual — part 877
MWI-80
< SYMPTOM DIAGNOSIS >
THE STEERING SWITCHES ARE INOPERATIVE
THE STEERING SWITCHES ARE INOPERATIVE
Description
INFOID:0000000009174299
One or more of the steering switches to control the information display are inoperative.
Diagnosis Procedure
INFOID:0000000009174300
1.
CHECK STEERING SWITCH CIRCUIT
Check steering switch circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connectors.
2.
CHECK STEERING SWITCH RESISTANCE
Check steering switch resistance. Refer to
MWI-70, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace steering switch. Refer to
AV-48, "Removal and Installation"
.
3.
CHECK SPIRAL CABLE
Check spiral cable for continuity. Refer to
MWI-70, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-82, "Removal and Installation"
NO
>> Replace spiral cable. Refer to
MWI
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
MWI-81
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
Description
INFOID:0000000009174301
• The displayed ambient air temperature is higher than the actual temperature.
• The displayed ambient air temperature is lower than the actual temperature.
Diagnosis Procedure
INFOID:0000000009174302
1.
CHECK COMBINATION METER INPUT SIGNAL
1. Select METER/M&A on CONSULT.
2. Check OUTSIDE TEMP of DATA MONITOR.
Does the ambient temperature approximately match the CONSULT display?
YES
>> Replace combination meter. Refer to
MWI-82, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK AMBIENT SENSOR SIGNAL CIRCUIT
Check the ambient sensor signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connectors.
3.
CHECK AMBIENT SENSOR
Check the ambient sensor. Refer to
HAC-87, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-82, "Removal and Installation"
NO
>> Replace ambient sensor. Refer to
MWI-82
< REMOVAL AND INSTALLATION >
COMBINATION METER
REMOVAL AND INSTALLATION
COMBINATION METER
Removal and Installation
INFOID:0000000009174303
REMOVAL
1. Remove cluster lid A. Refer to
IP-21, "Removal and Installation"
2. Remove the combination meter screws (A).
3. Disconnect the harness connector from the combination meter
(1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1435ZZ
MWI
TRIP RESET AND ILLUMINATION CONTROL SWITCH
MWI-83
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
TRIP RESET AND ILLUMINATION CONTROL SWITCH
Removal and Installation
INFOID:0000000009174304
ILLUMINATION CONTROL SWITCH
Removal
1. Remove cluster lid A. Refer to
IP-21, "Removal and Installation"
2. Release the harness connector from cluster lid A.
3. Release the clips (A) and remove illumination control switch (1)
through the front of cluster lid A (2).
Installation
Installation is in the reverse order of removal.
TRIP RESET SWITCH
Removal
1. Remove cluster lid A. Refer to
IP-21, "Removal and Installation"
2. Release the harness connector from cluster lid A.
ALNIA1437ZZ
ALNIA1438ZZ
ALNIA1439ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст