Nissan Pathfinder. Manual — part 383
DLK-298
< REMOVAL AND INSTALLATION >
HOOD LOCK
HOOD LOCK
Exploded View
INFOID:0000000009175889
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000009175890
REMOVAL
1. Remove front air duct. Refer to
2. Remove front fender protector (LH). Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installa-
3. Remove hood lock assembly bolts.
4. Disconnect hood lock release cable and secondary latch cable from hood lock assembly and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend cable too much, keeping the radius 100 mm (3.94 in) or more.
• Check that hood lock release cable and secondary latch cable are properly engaged with hood lock
assembly.
• After installation, perform hood assembly adjustment procedure. Refer to
• After adjusting, perform hood lock inspection. Refer to
DLK-298, "HOOD LOCK : Inspection"
HOOD LOCK : Inspection
INFOID:0000000009175891
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Hood lock assembly
2.
Hood lock release cable
3.
Hood lock release handle
4.
Secondary latch
AWKIA2630ZZ
HOOD LOCK
DLK-299
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1. Check that secondary latch is properly engaged with secondary striker with hoods own weight.
2. While operating hood lock release handle, carefully check that the front end of hood assembly is raised by
approximately 20.0 mm (0.79 in). Also check that hood lock release handle returns to the original position.
3. Check that hood lock release handle operates at 49 N (5.0 kg-m, 11.0 ft-lb) or below.
4. Install so that static closing force of hood is 315-490 N (32.1-50.0 kg–m, 70.8-110.2 ft–lb).
NOTE:
• Do not exert vertical force on right side and left side of hood lock.
• Do not press simultaneously on both sides.
5. Check the hood lock lubrication condition. If necessary, apply a suitable multi-purpose grease to hood lock
assembly.
SECONDARY LATCH
SECONDARY LATCH : Removal and Installation
INFOID:0000000009730836
REMOVAL
1. Remove radiator core support upper cover. Refer to
2. Disconnect secondary latch cable from hood lock assembly.
3. Remove bolts and secondary latch.
INSTALLATION
Installation is in the reverse order of removal.
HOOD LOCK RELEASE CABLE
HOOD LOCK RELEASE CABLE : Removal and Installation
INFOID:0000000009175892
REMOVAL
1. Remove fender protector (LH). Refer to
EXT-28, "FENDER PROTECTOR : Removal and Installation"
2. Remove front under cover. Refer to
EXT-30, "Removal and Installation"
.
3. Remove front air duct. Refer to
4. Remove radiator core support upper cover. Refer to
EXT-17, "Removal and Installation"
5. Disconnect hood lock release cable from hood lock release handle and hood lock assembly.
6. Release all hood lock release cable clips.
7. Remove grommet on the lower dash, and carefully pull the hood lock release cable into the passenger
compartment.
CAUTION:
While pulling, be careful not to damage (peel) the outside of hood lock release cable.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be careful not to bend cable too much, keep the radius 100 mm (3.94 in) or more.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet (at * mark) properly.
• Check that hood lock release cable is properly engaged with hood lock assembly.
• After installation, perform hood assembly adjustment procedure. Refer to
PIIB5801E
DLK-300
< REMOVAL AND INSTALLATION >
HOOD LOCK
• After adjusting, perform hood lock inspection. Refer to
FRONT DOOR LOCK
DLK-301
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR LOCK
Exploded View
INFOID:0000000009175893
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009175894
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Remove vapor barrier.
3. Remove front door lock bolts (A).
1.
Outside handle escutcheon
2.
Rear gasket
3.
Door key cylinder rod (LH only)
4.
Front door lock
5.
Cable clip
6.
Outside handle bracket
7.
Front gasket
8.
Outside handle
9.
Door key cylinder (LH only)
Front
AWKIA2613ZZ
AWKIA2614ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст