Nissan Pathfinder. Manual — part 382
DLK-294
< REMOVAL AND INSTALLATION >
BACK DOOR
BACK DOOR ASSEMBLY : Adjustment
INFOID:0000000009175883
Check the clearance and the surface height between back door and each part by visual inspection and tactile
feel. If the clearance and the surface height are out of specification, adjust them according to the adjustment
procedure.
1.
Back door assembly
2.
Roof panel
3.
Rear spoiler
4.
Body side outer
5.
Rear combination lamp
6.
Back-up lamp
7.
Rear bumper fascia
ALKIA2968ZZ
BACK DOOR
DLK-295
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Unit: mm (in)
1. Loosen back door hinge nuts (door side).
2. Lift up back door approximately 100 – 150 mm (3.94 – 5.91 in) height then close it lightly and check that it
is engaged firmly with back door closed.
3. Check the clearance and surface height according to the specifications provided.
4. Tighten back door hinge nuts to specified torque.
CAUTION:
• After installation, check back door open/close, lock/unlock operation.
• Check back door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-
purpose grease.
• After adjusting, apply touch-up paint (body color) to the head of rear door hinge bolts and nuts.
5. Install roof side molding (LH / RH). Refer to.
EXT-31, "Removal and Installation"
BACK DOOR STRIKER
BACK DOOR STRIKER : Removal and Installation
INFOID:0000000009175884
REMOVAL
1. Remove back door kicking plate. Refer to
INT-36, "BACK DOOR KICKING PLATE : Removal and Installa-
2. Remove bolts and back door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse back door striker bolts.
• After installation, check back door open/close operation. If necessary, adjust the door striker. Refer
DLK-295, "BACK DOOR STRIKER : Adjustment"
BACK DOOR STRIKER : Adjustment
INFOID:0000000009730831
DOOR STRIKER ADJUSTMENT
1. Loosen door striker bolts
2. Adjust door striker so that it becomes parallel with front door lock
insertion direction.
3. Tighten door striker bolts to specification. Refer to
.
Portion
Section
Item
Measurement
Standard
Difference
(LH/RH, MAX)
Roof panel – Rear spoiler
A – A
E
Clearance
7.0
± 1.5 (0.28 ± 0.06)
—
F
Surface height
1.5
± 1.5 (0.06 ± 0.06)
—
Body side outer – Back door assembly
B – B
G
Clearance
5.0
± 2.0 (0.20 ± 0.08)
≤2.0 (0.08)
H
Surface height
0.8
± 2.0 (0.03 ± 0.08)
≤2.0 (0.08)
Rear combination lamp – Back-up lamp
C – C
J
Clearance
5.0
± 2.0 (0.20 ± 0.08)
≤2.3 (0.09)
K
Surface height
0.0
± 2.1 (0.0 ± 0.08)
≤2.5 (0.10)
Rear bumper fascia – Back door assembly
D – D
M
Clearance
7.0
± 2.0 (0.28 ± 0.08)
—
N
Surface height
5.0
± 2.0 (0.20 ± 0.08)
≤2.0 (0.08)
ALKIA3218ZZ
DLK-296
< REMOVAL AND INSTALLATION >
BACK DOOR
BACK DOOR HINGE
BACK DOOR HINGE : Removal and Installation
INFOID:0000000009175885
REMOVAL
1. Remove back door assembly. Refer to
DLK-292, "BACK DOOR ASSEMBLY : Removal and Installation"
2. Remove back door hinge bolts (body side) and back door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the surface between hinge and body side.
• After installation, perform the back door assembly adjustment procedure. Refer to
SPINDLE UNIT
SPINDLE UNIT : Removal and Installation
INFOID:0000000009175886
REMOVAL
1. Support back door using a suitable tool.
WARNING:
Bodily injury may occur if the back door is not supported properly when removing the back door
spindle unit.
2. Partially remove headlining (rear edge).
3. Disconnect the harness connector from the spindle unit.
4. Release spindle unit from stud balls and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When reusing stud ball, always apply locking sealant before installing stud ball to back door.
• After installation, check back door open/close, lock/unlock operation.
BACK DOOR STAY
BACK DOOR STAY : Removal and Installation
INFOID:0000000009175887
REMOVAL
1. Support the back door using a suitable tool.
WARNING:
Body injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
2. Releaase the metal clip (3) located on the connection between
the back door stay (1) and the stud ball (2) (back door side)
using a suitable tool (A).
3. Remove the back door stay (back door side).
4. In the same way, remove the back door stay from the body side.
INSTALLATION
Installation is in the reverse order of removal.
JMKIA2255ZZ
BACK DOOR
DLK-297
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CAUTION:
After installation, check the back door open/close operation.
BACK DOOR WEATHER-STRIP
BACK DOOR WEATHER-STRIP : Removal and Installation
INFOID:0000000009175888
REMOVAL
Carefully remove back door weather-strip from opening door joint.
INSTALLATION
1. Beginning with upper section, align weather-strip mark with vehicle center position mark and install
weather strip to the vehicle.
2. For the lower section, align weather-strip seam with center of back door striker.
NOTE:
Pull weather-strip gently to ensure that there are no loose sections.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст