Nissan Pathfinder. Manual — part 384
DLK-302
< REMOVAL AND INSTALLATION >
FRONT DOOR LOCK
4. Disconnect door key cylinder rod (LH only) (1) from front door
lock (2) (LH only).
5. Disconnect door lock cables.
6. Disconnect the harness connector from the front door lock and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse front door lock bolts.
• After installation, check door lock cables are properly engaged to inside handle and outside handle
bracket.
• When installing door key cylinder rod (LH only), be sure to rotate door key cylinder rod holder until a
click is felt.
• After installation, check door open/close and lock/unlock operation.
• Check door lock assembly for poor lubrication. If necessary apply a suitable multi-purpose grease.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009175895
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Remove inside handle screws (A) and the inside handle (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check door lock cables are properly engaged to inside handle.
• After installation, check door open/close and lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000009175896
REMOVAL
1. Fully close front door glass.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
3. Remove vapor barrier.
NOTE:
ALKIA2487ZZ
ALKIA2715ZZ
FRONT DOOR LOCK
DLK-303
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Cut the butyl tape so that some parts of the butyl tape remain on the vapor barrier, if the vapor barrier is
reused.
4. Disconnect the harness connectors from the Intelligent Key antenna and door request switch and then
remove harness clamp on outside handle bracket.
5. Remove door side grommet (1), and remove bolt from grommet
hole (2).
6. Separate door key cylinder rod (LH only) (1) from door key cylin-
der assembly (LH only) (2).
7. While pulling (1) outside handle, remove (2) door key cylinder
assembly (LH side) or outside handle escutcheon (RH side).
8. While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9. Remove front gasket and rear gasket.
JMKIA5888ZZ
ALKIA2487ZZ
ALKIA2487ZZ
JMKIA0560ZZ
AWKIA1997ZZ
DLK-304
< REMOVAL AND INSTALLATION >
FRONT DOOR LOCK
10. Slide outside handle bracket toward rear of vehicle to remove.
11. Disconnect outside handle cable (1) from outside handle bracket
(2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing door key cylinder rod (LH only), be sure to rotate door key cylinder rod holder until a
click is felt.
• After installation, check door lock cable is properly engaged to outside handle bracket.
• After installation, check door open/close and lock/unlock operation.
JMKIA2652ZZ
ALKIA2489ZZ
REAR DOOR LOCK
DLK-305
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR LOCK
Exploded View
INFOID:0000000009175897
DOOR LOCK
DOOR LOCK : Removal and Installation
INFOID:0000000009175898
REMOVAL
1. Remove rear door finisher. Refer to
INT-17, "Removal and Installation"
.
2. Remove vapor barrier.
3. Remove rear door lock bolts.
4. Disconnect the door lock cables.
5. Disconnect the harness connector from the rear door lock and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse rear door lock bolts.
• After installation, check door lock cables are properly engaged to inside handle and outside handle.
• After installation, check door open/close and lock/unlock operation.
INSIDE HANDLE
INSIDE HANDLE : Removal and Installation
INFOID:0000000009175899
REMOVAL
1. Remove rear door finisher. Refer to
INT-17, "Removal and Installation"
.
1.
Outside handle
2.
Outside handle escutcheon
3.
Rear gasket
4.
Rear door lock
5.
Cable clip
6.
Outside handle bracket
7.
Front gasket
Front
AWKIA2616ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст