Nissan Pathfinder. Manual — part 1024
SE-94
< REMOVAL AND INSTALLATION >
SECOND ROW SEATS
Removal and Installation
INFOID:0000000009727779
LH SEAT
Removal
CAUTION:
• Before removal and installation, use shop cloths to protect parts from damage.
• During removal and installation, an assistant is required to protect against injury or damage.
1. Remove the rear kicking plate (LH). Refer to
INT-22, "KICKING PLATE : Removal and Installation - Rear
.
2. Remove the headrests (LH/RH).
3. Slide the seat to the full rearward position.
4. Remove the front slide finishers (LH/RH).
a. Pull up on the front edge to release pawls.
b. Then slide forward to remove from seat track.
5. Place the front cross brace (1) from Seat Fixture Kit [SST: — (J-
51030)] over the track alignment holes, then insert the two LH
threaded bolts (A) through the brace into the track and tighten.
: Front
6. Disconnect the harness connector (if equipped), then release from seat frame assembly.
7. Remove the seat front bolts.
8. Slide the seat to the full forward position.
9. Remove the rear slide finishers (LH/RH).
a. Pull up on the rear edge to release pawls.
b. Then slide forward to remove from seat track.
10. Place the rear cross brace (1) from Seat Fixture Kit [SST: — (J-
51030)] over the track alignment holes, then insert the four LH
threaded bolts (A) through the brace into the track and tighten.
: Front
11. Remove the seat rear bolts.
12. Fold the seatback in the flat position, then remove the seat from the vehicle.
19. EZ entry cable
20. Support strut
21. Inner finisher (LH)
22. Outer finisher (LH)
23. Seat harness
24. Seat cushion release cable
25. Seat slide release cable
26. Seat belt buckle
27. Rear finisher
28. Trim stiffener
29. Seatback board
30. Tether anchor finisher
31. EPP upper panel
32. Support finisher
33. Seatback pad
34. Seatback trim
35. Headrest holder (locked)
36. Headrest holder (free)
37. Headrest
A.
Seat cushion pivot bolt
ALJIA1106ZZ
AWJIA0954ZZ
SECOND ROW SEATS
SE-95
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Installation
Installation is in the reverse order of removal.
NOTE:
• When installing the LH seat, tighten the bolts in the order shown.
(
): Front
• Tighten the seat bolts to specification. Refer to
.
RH SEAT
Removal
CAUTION:
• Before removal and installation, use shop cloths to protect parts from damage.
• During removal and installation, an assistant is required to protect against injury or damage.
1. Remove the rear kicking plate (RH). Refer to
INT-22, "KICKING PLATE : Removal and Installation - Rear
.
2. Remove the headrest.
3. Slide the seat to the full rearward position.
4. Remove the front slide finishers (LH/RH).
a. Pull up on the front edge to release pawls.
b. Then slide forward to remove from seat track.
5. Place the front cross brace (1) from Seat Fixture Kit [SST: — (J-
51030)] over the track alignment holes, then insert the two LH
threaded bolts (A) through the brace into the track and tighten.
: Front
6. Disconnect the harness connector (if equipped), then release from seat frame assembly.
7. Remove the seat front bolts.
8. Slide the seat to the full forward position.
9. Remove the rear slide finishers (LH/RH).
a. Pull up on the rear edge to release pawls.
b. Then slide forward to remove from seat track.
10. Place the rear cross brace (1) from Seat Fixture Kit [SST: — (J-
51030)] over the track alignment holes, then insert the four LH
threaded bolts (A) through the brace into the track and tighten.
: Front
ALJIA1188ZZ
ALJIA1107ZZ
AWJIA0955ZZ
SE-96
< REMOVAL AND INSTALLATION >
SECOND ROW SEATS
11. Remove the seat rear bolts.
12. Fold the seatback in the flat position, then remove the seat from the vehicle.
Installation
Installation is in the reverse order of removal.
NOTE:
• When installing the RH seat, tighten the bolts in the order shown.
(
): Front
• Tighten the seat bolts to specification. Refer to
.
Armrest Assembly
INFOID:0000000009727780
REMOVAL
1. Press in the headrest holder button (A), then remove LH seat
headrest (RH) (1).
2. Remove the tether anchor finishers (2).
3. Remove seatback board (1).
: Clip
: Pawl
4. Remove four armrest assembly bolts (A) and pull the armrest
assembly (1) forward (
) to release clips.
: Metal clip
: Front
ALJIA1189ZZ
AWJIA0847ZZ
AWJIA0846ZZ
AWJIA0849ZZ
SECOND ROW SEATS
SE-97
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
5. Reach up behind the armrest assembly, release the headrest
holder locks as shown and remove the headrest holders.
CAUTION:
Before removing/installing headrest holder, check its orien-
tation (front/rear and right/left).
6. Remove the armrest assembly.
IINSTALLATION
Installation is in the reverse order of removal.
Seat Cushion
INFOID:0000000009727781
LH SEAT
Removal
1. Remove the recline lever.
a. Remove snap ring (2) upward using a suitable tool.
b. Remove recline lever (1).
2. Remove screw (
) and seat cushion outer finisher (LH) (3).
: Pawl
: Metal clip
3. Pull seat belt buckles through bottom of LH seat cushion.
4. Disconnect the harness connectors from the LH seat cushion heater (if equipped) and release the har-
ness from attachments.
NOTE:
Take note of harness routing and attachment location for correct installation.
5. Remove the support strut at bottom.
6. Remove seat cushion pivot bolt (
), then the LH seat cushion
(1).
Installation
Installation is in the reverse order of removal.
RH SEAT
Removal
JMJIA4073ZZ
AWJIA0965ZZ
ALJIA0851ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст