Nissan Pathfinder. Manual — part 750
BODY SIDE TRIM
INT-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000009176407
FRONT PILLAR FINISHER
FRONT PILLAR FINISHER : Removal and Installation
INFOID:0000000009176408
REMOVAL
1. Remove front kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and Installation - Front Kicking
.
2. Partially remove the front door welt.
1.
Front pillar finisher
2.
Front door welt
3.
Center pillar upper finisher
4.
Rear door welt
5.
Rear kicking plate
6.
Center pillar lower finisher
7.
Front kicking plate
Front
AWJIA1150ZZ
INT-20
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
3. Release the front pillar finisher metal clip and pawls using a suit-
able tool.
: Metal clip
: Clip
: Pawl
4. Cut and discard front pillar finisher tether clip (A).
CAUTION:
Do not reuse tether clips. Replace with new part after
removal.
5. Remove the remaining piece of tether clip (A) using a suitable
tool.
6. Disconnect the harness connector (if equipped) from the front pillar finisher, then remove the front pillar
finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse tether clips. Replace with new part after removal.
• Make sure to install tether clip to front pillar finisher before installing front pillar finisher.
• When installing tether clip to front pillar finisher, be sure to install by aligning to the cutout.
• Visually check the metal clip for deformation and damage during installation. Replace with new one
if necessary.
• When installing front pillar finisher, check that metal clip, tether clip and pawls are securely placed
into body panel holes.
CENTER PILLAR UPPER FINISHER
CENTER PILLAR UPPER FINISHER : Removal and Installation
INFOID:0000000009176409
REMOVAL
1. Move the front seat to the full forward position.
2. Remove the center pillar lower finisher. Refer to
INT-21, "CENTER PILLAR LOWER FINISHER : Removal
3. Release the center pillar upper finisher (A) pawl and clips using
a suitable tool.
CAUTION:
Do not bend the sheet metal when removing the center pil-
lar upper finisher from the sheet metal.
: Clip
: Pawl
ALJIA0817ZZ
ALJIA0819ZZ
BODY SIDE TRIM
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
4. Release seat belt retractor (1) from the lap belt pretensioner.
a. Insert suitable tool (A) into slots (B).
b. On opposite side insert suitable tool (C) into hole (D).
c. Depress suitable tools (A) and (C) at the same time and remove
seat belt retractor (1) as shown.
5. Remove the seat belt from the center pillar upper finisher and remove center pillar upper finisher.
CAUTION:
Do not reuse center pillar upper finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse center pillar upper finisher. Replace with new part for installation.
• Visually check the clips for deformation and damage during installation. Replace with new ones if
necessary.
• When installing center pillar upper finisher, check that the clips and pawl are securely placed in body
panel holes.
CENTER PILLAR LOWER FINISHER
CENTER PILLAR LOWER FINISHER : Removal and Installation
INFOID:0000000009176410
REMOVAL
1. Move the front seat to the full forward position.
2. Remove the front kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and Installation - Front Kick-
3. Remove the rear kicking plate. Refer to
INT-22, "KICKING PLATE : Removal and Installation - Rear Kick-
4. Release the center pillar lower finisher clips using a suitable
tool, then remove the center pillar lower finisher.
: Clip
INSTALLATION
ALHIA0321ZZ
AWJIA1149ZZ
INT-22
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips for deformation and damage during installation. Replace with new ones if
necessary.
• When installing center pillar lower finisher, check that clips are securely placed in body panel holes.
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation - Front Door Welt
INFOID:0000000009176411
REMOVAL
1. Remove the center pillar upper finisher. Refer to
INT-20, "CENTER PILLAR UPPER FINISHER : Removal
2. Remove the front body side welt.
INSTALLATION
Installation is in the reverse order of removal.
BODY SIDE WELT : Removal and Installation - Rear Door Welt
INFOID:0000000009176412
REMOVAL
1. Remove the center pillar upper finisher. Refer to
INT-20, "CENTER PILLAR UPPER FINISHER : Removal
2. Remove the rear body side welt.
INSTALLATION
Installation is in the reverse order of removal.
KICKING PLATE
KICKING PLATE : Removal and Installation - Front Kicking Plate
INFOID:0000000009176413
REMOVAL
1. Release the front kicking plate metal clips and pawls using a
suitable tool.
: Metal clip
: Pawl
: Front
2. Remove the front kicking plate.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Visually check the clips and pawls for deformation and damage during installation. Replace with new
ones if necessary.
• When installing front kicking plate, check that the clips and pawls are securely placed in body panel
holes.
KICKING PLATE : Removal and Installation - Rear Kicking Plate
INFOID:0000000009176414
REMOVAL
ALJIA0814ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст