Nissan X-Trail 32. Manual — part 1842
B260F ENGINE STATUS
SEC-135
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Refer to the following procedure.
• MR20DD:
EC-430, "Removal and Installation"
.
• QR25DE:
EC-806, "Removal and Installation"
.
• R9M:
EC-1226, "Removal and Installation"
.
>> INSPECTION END
SEC-136
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B261F ASCD CLUTCH SWITCH
B261F ASCD CLUTCH SWITCH
DTC Description
INFOID:0000000010922170
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connectors
(CAN communication line is open or shorted.)
• Harness or connectors
(Clutch pedal position switch circuit is open or shorted)
• Clutch pedal position switch
• Combination meter
• BCM
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK DTC PRIORITY
If DTC B261F-00 is displayed with DTC U1000-00 or U1010-00, first perform the trouble diagnosis for DTC
U1000-00 or U1010-00.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000-00: Refer to
NO
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Drive vehicle at a speed of 40 km/h (24.8 MPH) or more for 10 seconds.
3.
Decrease the vehicle speed to below 40 km/h (24.8 MPH).
4.
Repeat steps 2 and 3 twice (total of 3 times).
5.
Select “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
SEC-136, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010922171
1.
CHECK DTC PRIORITY
If DTC B261F-00 is displayed with DTC U1000-00 or U1010-00, first perform the trouble diagnosis for DTC
U1000-00 or U1010-00.
Is applicable DTC detected?
YES
>> Perform diagnosis of applicable. U1000-00: Refer to
NO
>> GO TO 2.
2.
CHECK DTC OF COMBINATION METER
Select “Self Diagnostic Result” mode of “METER/M&A” using CONSULT.
Refer to
.
Is the inspection result normal?
DTC No.
CONSULT screen items
(Trouble diagnosis content)
DTC detection condition
B261F-00
ASCD CNCL/CLTCH SW
(ASCD cancel/clutch switch)
BCM detects the following status for 10 seconds 3 times
• Clutch pedal position switch input: 0 V
• Vehicle speed: 40 km/h (24.8 MPH) or more
B261F ASCD CLUTCH SWITCH
SEC-137
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK CLUTCH PEDAL POSITION SWITCH SIGNAL
1.
Connect clutch pedal position switch connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
REPLACE BCM
BCS-121, "Removal and Installation"
.
>> INSPECTION END
5.
CHECK CLUTCH PEDAL POSITION SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and clutch pedal position switch connector.
3.
Check continuity between clutch pedal position switch harness connector and BCM harness connector.
4.
Check continuity between clutch pedal position switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK CLUTCH PEDAL POSITION SWITCH GROUND CIRCUIT
1.
Check continuity between clutch pedal position switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK CLUTCH PEDAL POSITION SWITCH
SEC-138, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 8.
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
E23
159
Ground
Clutch pedal posi-
tion switch
OFF (Clutch pedal
is depressed)
9 – 16 V
ON (Clutch pedal is
not depressed)
0 – 0.5 V
Clutch pedal position switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
E111
1
E23
159
Existed
Clutch pedal position switch
Ground
Continuity
Connector
Terminal
E111
1
Not existed
Clutch pedal position switch
Ground
Continuity
Connector
Terminal
E111
2
Existed
SEC-138
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B261F ASCD CLUTCH SWITCH
NO
>> Replace clutch pedal position switch. Refer to
CL-14, "LHD : Removal and Installation"
(LHD
models) or
CL-18, "RHD : Removal and Installation"
(RHD models).
8.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000010922172
1.
CHECK CLUTCH PEDAL POSITION SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect clutch pedal position switch connector.
3.
Check continuity between clutch pedal position switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace clutch pedal position switch. Refer to
CL-14, "LHD : Removal and Installation"
(LHD
models) or
CL-18, "RHD : Removal and Installation"
(RHD models).
Clutch pedal position switch
Condition
Continuity
Terminal
1
2
Clutch pedal
Not depressed
Existed
Depressed
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст