Nissan X-Trail 32. Manual — part 1954
SR-30
< REMOVAL AND INSTALLATION >
CURTAIN AIR BAG MODULE
REMOVAL
1.
Remove headlining assembly. Refer to
INT-37, "Removal and Installation"
2.
Disengage curtain air bag harness connector.
CAUTION:
• For installing/removing the curtain air bag harness con-
nector, insert a thin screwdriver wrapped in tape into
notch, lift lock and remove the connector.
• Install the connector with lock raised, and push lock into
the connector.
• After installing the connector, check that the lock is
pushed securely into it.
3.
Remove curtain air bag module mounting bolts, and then remove curtain air bag module.
CAUTION:
• To prevent damage to the parts, never impact the curtain air
bag module.
• Replace the curtain air bag module if it is dropped or sustains
an impact.
• To prevent accidental explosion, never insert any foreign objects (screwdriver, etc.) into the curtain
air bag module.
• To prevent accidental explosion, never disassemble the curtain air bag module.
• To prevent accidental explosion, never expose the curtain air bag module to temperatures of more
than 90
°
C (194
°
F).
• To prevent damage to the parts, never allow oil, grease, detergent, or water to come in contact with
the curtain air bag module.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check perforation of curtain air bag module to check that curtain air bag module is not twisted.
• Never damage the harness while installing.
• After installation is complete, perform self-diagnosis using CONSULT or air bag warning lamp, if the
system is normal and
″
PAST
″
of
″
Self Diagnostic Result
″
is indicated, always perform
″
ERASE
″
of
″
Self Diagnostic Result
″
using CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
PHIA0953J
JMHIA0009ZZ
CRASH ZONE SENSOR
SR-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
CRASH ZONE SENSOR
Exploded View
INFOID:0000000010927734
Removal and Installation
INFOID:0000000010927735
WARNING:
Always observe the following items for preventing accidental activation.
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more (discharges electricity held in the additional power supply circuit of the air bag diagno-
sis sensor unit).
REMOVAL
1.
Remove the crash zone sensor mounting nuts, and then remove bracket.
2.
Disconnect the crash zone sensor harness connector, and then remove crash zone sensor.
CAUTION:
• To prevent damage to the parts, never impact the crash zone
sensor.
• Replace the crash zone sensor if it is dropped or sustains an
impact.
Crash zone sensor
Bracket
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA2882GB
JMHIA0009ZZ
SR-32
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
• Replace the crash zone sensor of deployed driver air bag module, deployed passenger air bag mod-
ule, seat belt pre-tensioner and deployed lap pre-tensioner.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never reuse mounting nut after removal, replace with new nut.
• Always install normally aligning to the cutout hole, because performance of the crash zone sensor
excessively fluctuates according to the installation position.
• After installation is complete, perform self-diagnosis using CONSULT or air bag warning lamp, if the
system is normal and
″
PAST
″
of
″
Self Diagnostic Result
″
is indicated, always perform
″
ERASE
″
of
″
Self Diagnostic Result
″
using CONSULT. Refer to
.
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
SATELLITE SENSOR
SR-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
SATELLITE SENSOR
Exploded View
INFOID:0000000010927736
Removal and Installation
INFOID:0000000010927737
WARNING:
Always observe the following items for preventing accidental activation.
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-
utes or more (discharges electricity held in the additional power supply circuit of the air bag diagno-
sis sensor unit).
REMOVAL
B-pillar Satellite Sensor
1.
Remove center pillar lower garnish. Refer to
INT-27, "CENTER PILLAR LOWER GARNISH : Removal
2.
Remove B-pillar satellite sensor mounting nuts.
3.
Pull out B-pillar satellite sensor from the vehicle.
CAUTION:
Never damage the B-pillar satellite sensor harness.
4.
Disconnect the B-pillar satellite sensor harness connector, and then remove the B-pillar satellite sensor.
CAUTION:
B-pillar satellite sensor
C-pillar satellite sensor (if equipped)
: Vehicle front
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JMHIA2883GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст