Nissan X-Trail 32. Manual — part 1643
PB-98
< DTC/CIRCUIT DIAGNOSIS >
C1BD7 CLUTCH SENSOR SYSTEM
s the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace error-detected parts, and GO TO 7.
7.
CHECK CLUTCH PEDAL STROKE SENSOR CIRCUIT
1.
Turn the ignition switch OFF.
2.
Check the continuity between clutch pedal stroke sensor harness connector and ground.
s the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace error-detected parts, and GO TO 8.
8.
CHECK CONNECTOR AND TERMINAL
1.
Check the clutch pedal stroke sensor harness connector for disconnection or looseness.
2.
Check the clutch pedal stroke sensor pin terminals for damage or loose connection with harness connec-
tor.
3.
Check the electric parking brake control module harness connector for disconnection or looseness.
4.
Check the electric parking brake control module pin terminals for damage or loose connection with har-
ness connector.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace error-detected parts, and GO TO 9.
9.
CHECK DATA MONITOR
With CONSULT
1.
Turn the ignition switch ON.
2.
Select “EHS/PKB” and “DATA MONITOR” according to this order.
3.
Check the “CLUTCH PEDAL” of monitor item.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace error-detected parts, and GO TO 10.
10.
REPLACE CLUTCH PEDAL STROKE SENSOR
Replace the clutch pedal stroke sensor.
• LHD models: Refer to
CL-14, "LHD : Removal and Installation"
.
• RHD models: Refer to
CL-18, "RHD : Removal and Installation"
.
>> GO TO 11.
11.
CULTCH PEDAL STROKE SENSOR RESET
With CONSULT
1.
Connect the clutch pedal stroke sensor harness connector.
2.
Turn the ignition switch ON.
3.
Perform clutch pedal stroke sensor reset. Refer to
.
>> GO TO 12.
Clutch pedal stroke sensor
—
Voltage
Connector
Terminal
E24
1
Ground
4.75
−
5.25 V
Clutch pedal stroke sensor
—
Continuity
Connector
Terminal
E24
2
Ground
Not existed
3
Existed
C1BD7 CLUTCH SENSOR SYSTEM
PB-99
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
12.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds or more after turning the ignition switch OFF.
2.
Erase self-diagnosis result for “EHS/PKB”.
3.
Repeat the parking brake switch operation (pull and push) five times.
4.
Perform self-diagnosis for “EHS/PKB”.
Is DTC “C1BD7” detected?
YES
>> Replace the electric parking brake control module. Refer to
PB-153, "Removal and Installation"
NO
>> INSPECTION END
PB-100
< DTC/CIRCUIT DIAGNOSIS >
C1BD9 INITIALIZE POSITION
C1BD9 INITIALIZE POSITION
DTC Description
INFOID:0000000010722982
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Parking brake actuator
• Electric parking brake control module
FAIL-SAFE
Automatic apply and release are prohibited.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds after turning ignition switch OFF or ON.
2.
Push the parking brake switch.
CAUTION:
• Set the select lever in the P position.
• Depress the brake pedal.
3.
Pull the parking brake switch.
4.
Perform self-diagnosis for “EHS/PKB”.
Is DTC “C1BD9” detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010722983
1.
ERASE SELF-DIAGNOSIS RESULT
With CONSULT
1.
Turn the ignition switch ON.
2.
Erase self-diagnosis result for “EHS/PKB”.
>> GO TO 2.
2.
PERFORM WORK SUPPORT
With CONSULT
Perform “INITIALZATION POSITION ADJUSTMENT” of “WORK SUPPORT”. Refer to
.
Is the inspection result normal?
>> GO TO 3.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BD9
INITIALIZE POSITION
(Initialize position)
Parking brake actuator (integrated in spindle and nut) has not been initialized.
C1BD9 INITIALIZE POSITION
PB-101
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
3.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “EHS/PKB”.
Is DTC “C1BDF” detected?
YES
>> Replace the electric parking brake control module. Refer to
PB-153, "Removal and Installation"
NO
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст