Nissan X-Trail 32. Manual — part 1642
PB-94
< DTC/CIRCUIT DIAGNOSIS >
C1BD6 DOOR SYSTEM
C1BD6 DOOR SYSTEM
DTC Description
INFOID:0000000010722978
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Electric parking brake control module
• Door switch (Driver side)
• BCM
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds after turning ignition switch OFF or ON.
2.
Push the parking brake switch.
CAUTION:
• Set the select lever in the P position.
• Depress the brake pedal.
3.
Pull the parking brake switch.
4.
Perform self-diagnosis for “EHS/PKB”.
Is DTC “C1BD6” detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010722979
1.
ERFORM SELF-DIAGNOSIS (1)
With CONSULT
Perform self-diagnosis for “BCM”.
Is DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 2.
2.
CHECK DATA MONITOR
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds or more after turning the ignition switch OFF.
2.
Select “BCM” and “DATA MONITOR” according to this order.
3.
Check the “DOOR STAT-DR” of monitor item. Refer to
Is the inspection result normal?
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BD6
DOOR SW
(Door switch)
Door switch (driver side) signal is not input when door open or close.
C1BD6 DOOR SYSTEM
PB-95
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
YES
>> GO TO 3.
NO
>>
Check the door switch system.
• With Intelligent Key and super lock: Refer to
DLK-186, "Diagnosis Procedure"
.
• With Intelligent Key, without super lock: Refer to
DLK-495, "Diagnosis Procedure"
.
• Without Intelligent Key, with super lock: Refer to
DLK-695, "Diagnosis Procedure"
.
• Without Intelligent Key and super lock: Refer to
DLK-842, "Diagnosis Procedure"
.
3.
PERFORM SELF-DIAGNOSIS (2)
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds or more after turning the ignition switch OFF.
2.
Erase self-diagnosis result for “EHS/PKB”.
3.
Repeat the parking brake switch operation (pull and push) five times.
4.
Perform self-diagnosis for “EHS/PKB”.
Is DTC “C1BD6” detected?
YES
>> Replace the electric parking brake control module. Refer to
PB-153, "Removal and Installation"
NO
>> INSPECTION END
PB-96
< DTC/CIRCUIT DIAGNOSIS >
C1BD7 CLUTCH SENSOR SYSTEM
C1BD7 CLUTCH SENSOR SYSTEM
DTC Description
INFOID:0000000010722980
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Harness or connector
• Clutch pedal stroke sensor
• Electric parking brake control module
FAIL-SAFE
Automatic apply and release are prohibited. (Mechanical release can be performed.)
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds after turning ignition switch OFF or ON.
2.
Push the parking brake switch.
CAUTION:
• Set the select lever in the P position.
• Depress the brake pedal.
3.
Pull the parking brake switch.
4.
Perform self-diagnosis for “EHS/PKB”.
Is DTC “C1BD7” detected?
YES
>> Proceed to
NO-1
>> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010722981
1.
VISUALLY CHECK CLUTCH PEDAL STROKE SENSOR
1.
Turn the ignition switch OFF.
2.
Check the clutch pedal stroke sensor for damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected part, and GO TO 2.
2.
CHECK CLUTCH PEDAL STROKE SENSOR INSTALLATION
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BD7
CLUTCH SENSOR
(Clutch sensor)
• Open circuit is detected in clutch pedal stroke sensor circuit.
• Short circuit is detected in clutch pedal stroke sensor circuit.
• Malfunction is detected in clutch pedal stroke sensor circuit.
• An internal malfunction is detected in clutch pedal stroke sensor. (With fluctuations
in output voltage of clutch pedal stroke sensor)
• An internal malfunction is detected in clutch pedal stroke sensor. (Without fluctua-
tions in output voltage of clutch pedal stroke sensor)
• Poor installation is detected in clutch pedal stroke sensor.
• When reset of clutch pedal stroke sensor is not complete.
C1BD7 CLUTCH SENSOR SYSTEM
PB-97
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
Check the clutch pedal stroke sensor for looseness and disconnection.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected part, and GO TO 3.
3.
CULTCH PEDAL STROKE SENSOR RESET
With CONSULT
1.
Turn the ignition switch ON.
2.
Perform clutch pedal stroke sensor reset. Refer to
.
>> GO TO 4.
4.
PERFORM SELF-DIAGNOSIS (1)
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds or more after turning the ignition switch OFF.
2.
Erase self-diagnosis result for “EHS/PKB”.
3.
Repeat the parking brake switch operation (pull and push) five times.
4.
Perform self-diagnosis for “EHS/PKB”.
Is DTC “C1BD7” detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
CHECK CLUTCH PEDAL STROKE SENSOR CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect the clutch pedal stroke sensor harness connector.
3.
Disconnect the electric parking brake control module harness connector.
4.
Check the continuity between clutch pedal stroke sensor harness connector and electric parking brake
control module harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace error-detected parts, and GO TO 6.
6.
CHECK CLUTCH PEDAL STROKE SENSOR POWER SUPPLY
1.
Connect the electric parking brake control module harness connector.
2.
Turn the ignition switch ON.
3.
Check the voltage clutch pedal stroke sensor harness connector terminals.
Electric parking brake control module
Clutch pedal stroke sensor
Continuity
Connector
Terminal
Connector
Terminal
M137
24
E24
1
Not existed
24
2
Not existed
24
3
Existed
25
1
Not existed
25
2
Existed
25
3
Not existed
26
1
Existed
26
2
Not existed
26
3
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст