Nissan X-Trail 32. Manual — part 2185
TM-698
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
CVT FLUID COOLER SYSTEM
Inspection and Adjustment
INFOID:0000000010622912
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
Hose
Installation side tube
Hose clamp
Direction of tab
Clamping position (A)
Fluid cooler
hose B
CVT fluid cooler tube
A
Frontward
5 – 9 mm (0.20 – 0.35
in) from hose end
Fluid cooler tube as-
sembly
Leftward
Fluid cooler
hose C
Fluid cooler tube as-
sembly
CVT fluid cooler
Frontward
Fluid cooler
hose D
CVT fluid cooler
Fluid cooler bracket
(with tube)
Fluid cooler
hose E
Fluid cooler bracket
(with tube)
Fluid cooler tube as-
sembly
Leftward
Fluid cooler
hose F
Fluid cooler tube as-
sembly
CVT oil warmer
Upward
JSDIA2424ZZ
CVT OIL WARMER
TM-699
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CVT OIL WARMER
Exploded View
INFOID:0000000010622919
Removal and Installation
INFOID:0000000010622920
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform when the engine is cold.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid/coolant
from spilling.
1.
Remove the battery tray. Refer to
PG-148, "EXCEPT FOR R9M : Removal and Installation"
2.
Remove harness bracket
.
3.
Remove water hose A and B from CVT oil warmer. Refer to
TM-692, "Removal and Installation"
4.
Remove fluid cooler hose A and F from CVT oil warmer. Refer to
TM-695, "Removal and Installation"
.
5.
Remove fluid cooler tube A from transaxle assembly. Refer to
TM-695, "Removal and Installation"
.
6.
Remove mounting bolts (
) and remove CVT oil warmer
from transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
Transaxle assembly
CVT oil warmer
: N·m (kg-cm, in-lb)
JSDIA5225GB
JSDIA5245ZZ
TM-700
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
CVT OIL WARMER
Inspection and Adjustment
INFOID:0000000010622921
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid and engine coolant.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
PLUG
TM-701
< REMOVAL AND INSTALLATION >
[CVT: RE0F10G]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PLUG
Description
INFOID:0000000010622925
Replace the O-ring if oil leakage or exudes from the plug.
Exploded View
INFOID:0000000010622926
Removal and Installation
INFOID:0000000010622927
REMOVAL
1.
Remove splash side cover LH. Refer to
EXT-35, "FENDER PROTECTOR : Exploded View"
.
2.
Remove the plug and O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection and Adjustment
INFOID:0000000010622928
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
Transaxle assembly
O-ring
Plug
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Apply CVT fluid
JSDIA5433GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст