Nissan X-Trail 32. Manual — part 1774
RSU-18
< REMOVAL AND INSTALLATION >
UPPER LINK
1.
Check wheel sensor harness for proper connector. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
.
REAR STABILIZER
RSU-19
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR STABILIZER
Exploded View
INFOID:0000000010822794
Removal and Installation
INFOID:0000000010822795
REMOVAL
1.
Remove stabilizer link.
2.
Remove main muffler.
• MR20DD: Refer to
EX-6, "Removal and Installation"
• QR25DE: Refer to
EX-12, "Removal and Installation"
• R9M: Refer to
EX-18, "Removal and Installation"
3.
Remove mounting nuts on stabilizer clamp and stabilizer bar from suspension member.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000010822796
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer link, stabilizer bushing and stabilizer clamp for deformation, cracks or damage.
Replace it if necessary.
Stabilizer bar
Rear suspension member
Lower link
Stabilizer clamp
Stabilizer bushing
Stabilizer link
: N·m (kg-m, ft-lb)
: Vehicle front
JSEIA0910GB
RSU-20
< REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000010822797
Removal and Installation
INFOID:0000000010822798
REMOVAL
1.
Remove tires. Refer to
2.
Remove wheel sensor and sensor harness. Refer to
BRC-214, "REAR WHEEL SENSOR : Removal and
.
3.
Remove caliper assembly. Hang caliper assembly not to interfere with work.
• LHD: Refer to
BR-63, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
• RHD: Refer to
BR-123, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
4.
Remove disc rotor.
• 2WD: Refer to
RAX-7, "Removal and Installation"
.
• 4WD: Refer to
RAX-18, "Removal and Installation"
.
CAUTION:
• Put matching marks on the wheel hub assembly and the disc rotor before removing the disc
rotor.
• Never drop disc rotor.
5.
Remove parking brake cable mounting bolt. Refer to
PB-154, "Removal and Installation"
.
6.
Removal rear hight sensor (with LED head lamp). Refer to
EXL-200, "REAR HEIGHT SENSOR :
.
7.
Remove center muffler and main muffler.
• MR20DD: Refer to
EX-6, "Removal and Installation"
• QR25DE: Refer to
EX-12, "Removal and Installation"
• R9M: Refer to
EX-18, "Removal and Installation"
.
8.
Remove stabilizer bar and stabilizer link. Refer to
RSU-19, "Removal and Installation"
.
9.
Remove drive shaft (4WD). Refer to
RAX-22, "Removal and Installation"
.
10. Remove propeller shaft (4WD). Refer to
DLN-214, "Removal and Installation"
.
Rear suspension member
Suspension member stay (right side)
Suspension member stay (left side)
: N·m (kg-m, ft-lb)
: Vehicle front
JSEIA0911GB
REAR SUSPENSION MEMBER
RSU-21
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
11. Remove rear final drive (4WD). Refer to
DLN-239, "Removal and Installation"
.
12. Remove rear shock absorber. Refer to
RSU-13, "Removal and Installation"
13. Remove coil spring. Refer to
RSU-9, "Removal and Installation"
.
14. Set jack rear suspension member.
CAUTION:
• Check the stable condition when using a jack.
• Never damage rear lower link with a jack.
15. Remove rear suspension member mounting bolt.
16. Slowly lower jack, remove rear suspension member with lower link and upper link.
CAUTION:
Operate while checking that jack supporting status is stable.
17. Remove suspension member stay, lower link and upper link from suspension member.
18. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Align the matching marks that have been made during removal when reusing the disc rotor.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
rear suspension assembly.
• Perform inspection after installation. Refer to
Inspection
INFOID:0000000010822799
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Check wheel sensor harness for proper connection. Refer to
.
2.
Check wheel alignment. Refer to
3.
Adjust neutral position of steering angle sensor. Refer to
.
4.
After final tightening, install rear hight sensor (with LED head lamp). Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст