Nissan X-Trail 32. Manual — part 1078
DRIVE PLATE
EM-209
< UNIT DISASSEMBLY AND ASSEMBLY >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Secure drive plate with a stopper plate [SST: KV11105210]
(A), and remove mounting bolts.
• Using TORX socket (size E20) (B), loosen mounting bolts.
• loosen mounting bolts in diagonal order.
CAUTION:
• Never disassemble them.
3.
Remove pilot converter
, from the rear end of the crankshaft.
Use a pilot bushing puller (commercial service tool) (A), if neces-
sary.
INSTALLATION
1.
Install pilot converter.
2.
Install drive plate in the reverse order of removal.
• Install drive plate
, reinforcement plate
and pilot converter
as shown in figure.
• Using a drift of 33 mm (1.30 in) in diameter, press-fit pilot con-
verter into the end of crankshaft until it stops.
Inspection
INFOID:0000000010783808
DRIVE PLATE DEFLECTION
• Measure the deflection of drive plate contact surface to torque con-
verter with a dial indicator (A).
• Measure the deflection at the area limited 20.6 mm (0.811 in) dia
around hole
.
• If measured value is out of the standard, replace drive plate.
JSBIA3353ZZ
JSBIA3354ZZ
: Crankshaft rear end
: Rounded
: Chamfered
PBIC3259J
Limit : 0.35 mm (0.0138 in) or less.
JSBIA3355ZZ
EM-210
< UNIT DISASSEMBLY AND ASSEMBLY >
[QR25DE]
TIMING CHAIN
TIMING CHAIN
Exploded View
INFOID:0000000010783809
Camshaft sprocket (EXH)
Camshaft sprocket (INT)
O-ring
O-ring
Valve timing control cover
O-ring
Intermdeiate valve timing control so-
lenoid valve
Intake valve timing control solenoid
valve
Exhaust valve timing control solenoid
valve
Crankshaft pulley bolt
Crankshaft pulley
Front oil seal
O-ring
O-ring
Oil pump drive spacer
Crankshaft sprocket
Balancer unit sprocket
Balancer unit timing chain
Balancer unit timing chain tensioner
Balancer unit
Crankshaft key
O-ring
Timing chain tension guide
Timing chain slack guide
Chain tensioner
Timing chain
O-ring
Front cover
Oil filter
O-ring
JSBIA3356GB
TIMING CHAIN
EM-211
< UNIT DISASSEMBLY AND ASSEMBLY >
[QR25DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000010783810
REMOVAL
1.
Remove the following parts.
• PCV hose: Refer to
• Intake manifold: Refer to
.
• Ignition coil: Refer to
• Drive belt: Refer to
EM-166, "Removal and Installation"
.
• Drive belt auto-tensioner: Refer to
.
2.
Remove engine mounting bracket (RH).
3.
Remove rocker cover. Refer to
EM-190, "Removal and Installation"
4.
Remove oil pan (lower). Refer to
.
5.
Remove oil pan (upper), and oil strainer. Refer to
6.
Remove valve timing control cover.
• Loosen bolts in reverse order as shown in the figure.
NOTE:
Do not loosen screws
on the back of the valve timing control
cover.
7.
Pull chain guide between camshaft sprockets out through front cover.
8.
Set No. 1 cylinder at TDC on its compression stroke with the following procedure:
Oil pressure sensor
Comply with the assembly procedure
when tightening. Refer to
Comply with the assembly procedure
when tightening. Refer to
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Should be lubricated with oil.
: Sealing point
: Indicates that the part is connected at points with same symbol in actual vehicle.
ALBIA0839GB
AWBIA1361ZZ
EM-212
< UNIT DISASSEMBLY AND ASSEMBLY >
[QR25DE]
TIMING CHAIN
a.
Rotate crankshaft pulley
clockwise and align TDC mark (no
paint)
to timing indicator
on front cover.
b.
At the same time, check that the mating marks
on camshaft
sprockets are located as shown in the figure.
• If not, rotate crankshaft pulley one more turn to align mating
marks to the positions in the figure.
9.
Remove crankshaft pulley with the following procedure:
a.
Fix crankshaft pulley
with a pulley holder (commercial service
tool) (A), loosen crankshaft pulley bolt, and locate bolt seating
surface at 10 mm (0.39 in) from its original position.
b.
Attach a pulley puller [SST:KV11103000] (A) in the M6 thread
hole on crankshaft pulley, and remove crankshaft pulley.
10. Remove front cover with the following procedure:
: Paint mark (Not use for service)
JSBIA3308ZZ
: Camshaft sprocket (INT)
: Camshaft sprocket (EXH)
JSBIA3357ZZ
ALBIA0857GB
JSBIA2453ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст