Nissan X-Trail 32. Manual — part 1569
MA-66
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown in
the figure.
CAUTION:
Never install one balance weight sheet on top of another.
3.
Start the tire balance machine again.
4.
Install drive-in balance weight on inner side of road wheel in the tire balance machine indication position
(angle).
CAUTION:
Never install three or more balance weight.
5.
Start the tire balance machine. Check that the inner and outer residual unbalance value is within the
allowable unbalance value.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
WHEELS : Wheel Balance Adjustment (Steel Wheel)
INFOID:0000000010828075
PREPARATION BEFORE ADJUSTMENT
Remove balance weight from the road wheel.
CAUTION:
Never scratch the road wheel during removal.
ADJUSTMENT
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction manual.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for steel wheels.
1.
Set road wheel to wheel balancer, and then start wheel balancer.
2.
Install balance weight to road wheel according to the unbalance and position (angle) displayed on wheel
balancer.
CAUTION:
• Always use genuine NISSAN balance weights.
• Balance weights are non-reusable; always replace with new ones.
• Always use a plastic hammer when attaching the weight.
• Never install three or more balance weights on one side.
3.
Start the tire balance machine. Check that the inner and outer residual unbalance value is within the
allowable unbalance value.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
PEIA0033E
Allowable unbalance value
Dynamic (At flange)
: Refer to
.
Static (At flange)
: Refer to
.
Allowable unbalance value
Dynamic (At flange)
: Refer to
.
Static (At flange)
: Refer to
.
CHASSIS MAINTENANCE
MA-67
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
WHEELS : Tire Rotation
INFOID:0000000010828076
• Follow the maintenance schedule for tire rotation service intervals.
• When installing the wheel, tighten wheel nuts to the specified
.
CAUTION:
• Never include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Never tighten wheel nut at torque exceeding the criteria.
• Use NISSAN genuine wheel nut.
• After tire rotation, perform following:
- Perform the ID registration. Refer to
.
- Perform TPMS reset operation. Refer to
BRAKE FLUID LEVEL AND LEAKS
BRAKE FLUID LEVEL AND LEAKS : Inspection
INFOID:0000000010735337
• If fluid level is extremely low, check brake system for leaks.
BRAKE LINES AND CABLES
BRAKE LINES AND CABLES : Inspection
INFOID:0000000010735338
• Check brake/clutch fluid lines and parking brake cables for
improper attachment, leaks, chafing, abrasions, deterioration, etc.
BRAKE FLUID
SMA829C
JPFIA0007ZZ
SBR389C
MA-68
< PERIODIC MAINTENANCE >
CHASSIS MAINTENANCE
BRAKE FLUID : Changing
INFOID:0000000010735339
1.
Drain brake fluid from each bleed valve.
2.
Refill until new brake fluid comes out from each bleed valve.
Use same procedure as in bleeding hydraulic system to refill
brake fluid.
Refer to
BR-14, "Bleeding Brake System"
(LHD),
• Refill with recommended brake fluid.
Refer to
MA-23, "Fluids and Lubricants"
.
• Never reuse drained brake fluid.
• Be careful not to splash brake fluid on painted areas.
DISC BRAKE (LHD)
DISC BRAKE (LHD) : Inspection
INFOID:0000000010735340
DISC ROTOR
Check condition, wear, and damage.
CALIPER
• Check for leakage.
BRAKE PAD
• Check for wear or damage.
DISC BRAKE (LHD) : Front Disc Brake
INFOID:0000000010953454
Unit: mm (in)
SBR419C
SMA922A
BRA0010D
Item
Limit
Brake caliper type
1 piston type
2 piston type
Brake pad
Wear thickness
2.0 (0.079)
2.0 (0.079)
Disc rotor
Wear thickness
24.0 (0.945)
26.0 (1.0236)
Thickness variation (measured at 8 positions)
0.020 (0.0008)
0.020 (0.0008)
Runout (with it attached to the vehicle)
0.035 (0.0014)
0.035 (0.0014)
CHASSIS MAINTENANCE
MA-69
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
B
MA
N
O
A
DISC BRAKE (LHD) : Rear Disc Brake
INFOID:0000000010953455
Unit: mm (in)
DISC BRAKE (RHD)
DISC BRAKE (RHD) : Inspection
INFOID:0000000010735343
DISC ROTOR
Check condition, wear, and damage.
CALIPER
• Check for leakage.
BRAKE PAD
• Check for wear or damage.
DISC BRAKE (RHD) : Front Disc Brake
INFOID:0000000010953494
Unit: mm (in)
Item
Limit
Brake pad
Wear thickness
2.0 (0.079)
Disc rotor
Wear thickness
14.0 (0.551)
Thickness variation (measured at 8 positions)
0.020 (0.0008)
Runout (with it attached to the vehicle)
0.070 (0.0028)
SMA922A
BRA0010D
Item
Limit
Brake caliper type
1 piston type
2 piston type
Brake pad
Wear thickness
2.0 (0.079)
2.0 (0.079)
Disc rotor
Wear thickness
24.0 (0.945)
26.0 (1.0236)
Thickness variation (measured at 8 positions)
0.020 (0.0008)
0.020 (0.0008)
Runout (with it attached to the vehicle)
0.035 (0.0014)
0.035 (0.0014)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст