Nissan X-Trail 32. Manual — part 285
CL-8
< SYMPTOM DIAGNOSIS >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010745319
Use the chart below to find the cause of the symptom. The numbers indicate the order of the inspection. If nec-
essary, repair or replace these parts.
SUSPECTED PARTS (Possible cause)
CLUTCH P
E
DAL (I
ns
pe
ct
ion
a
nd
ad
ju
stm
e
n
t)
CLUTCH LINE (A
ir in line)
MA
STER CYLINDER PIS
T
ON CUP (Damaged)
ENGINE MOU
N
TING (Loose)
CSC (Con
ce
nt
ric
Sla
v
e
Cy
lin
de
r) (W
orn
, d
irty
or
da
ma
ge
d)
CLUTCH DISC (Out
of
true)
CLUTCH DISC (Runou
t i
s
ex
ce
ssi
v
e
)
CLUTCH DISC (Lining
broken)
CLUTCH DISC (Dirty or burned)
CLUTCH DISC (Oily)
CLUTCH DISC (W
orn out)
CLUTCH DISC (Hardened)
CLUTCH DISC (Lack of
s
p
line
g
rea
se
)
DI
APHRAGM SPRI
N
G (Dam
ag
ed
)
DIAPHRAGM
SPRING (Ou
t of
ti
p a
lig
nm
en
t)
PRESSURE P
L
A
T
E (Di
s
to
rti
o
n)
FL
YWHE
EL (Di
s
tortion)
Reference
(LHD),
(RHD)
(MR20DD
),
(R9M)
(MR20DD
),
(R9M)
(MR20DD),
(R9M)
Symptom
Clutch grabs/chatters
1
2
2
2
2
2
Clutch pedal spongy
1
2
2
Clutch noisy
1
Clutch slips
1
2
2
3
4
5
Clutch does not disengage
1
2
3
4
4
4
4
4
4
4
5
5
6
CLUTCH PEDAL
CL-9
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
PERIODIC MAINTENANCE
CLUTCH PEDAL
Inspection and Adjustment
INFOID:0000000010745320
INSPECTION
Clutch Pedal Height
1.
Turn the floor carpet.
2.
Check that the clutch pedal height (H
1
) from the surface
for
measurement is within the reference value.
• Replace clutch pedal if the height is outside the reference
value.
Clutch Pedal Height when Disengaging the Clutch
1.
Securely engage the parking brake.
2.
Turn the floor carpet.
3.
Start the engine and run at idle.
4.
Fully depress clutch pedal and shift to the 1st gear.
CAUTION:
Securely depress the brake pedal with shift lever in 1st gear.
5.
Gradually release the clutch pedal and check that the clutch
pedal height (H
2
) from the surface
for measurement is within
the reference value with a scale immediately before the clutch is
engaged.
• Replace clutch pedal if the height is outside the reference
value.
NOTE:
Although the clutch pedal height differs according to whether the clutch gets disengaged or engaged,
clutch-engaged case is regarded as clutch-disengaged case for easier inspection.
Clutch Pedal Play
Push the pedal pad by hand until a resistance can be felt and check
that the play (A) on the upper surface of the pedal pad is within the
reference value.
• Replace clutch pedal if the play is outside the reference value.
Position of Clutch Interlock Switch
Measurement surface
: Top surface of floor panel
Clutch pedal height
: Refer to
.
JPFIA0065ZZ
Measurement surface
: Top surface of floor panel
Clutch pedal height at
clutch disengagement
.
JPFIA0068ZZ
Clutch pedal play
: Refer to
.
JPFIA0121ZZ
CL-10
< PERIODIC MAINTENANCE >
CLUTCH PEDAL
Check that the clearance (C) between the thread end of clutch inter-
lock switch
and clutch pedal lever
is within the specified value
while clutch pedal is fully depressed.
Position of Clutch Pedal Position Switch
Check that the clearance (C) between the thread end of clutch pedal
position switch
and clutch pedal lever
is within the specified
value while clutch pedal is fully released.
ADJUSTMENT
Position of Clutch Interlock Switch
1.
Disconnect the clutch interlock switch connector.
2.
Loosen the clutch interlock switch 45 degrees counterclockwise.
3.
With the clutch pedal fully depressed, press into the clutch inter-
lock switch
until it reaches the clutch pedal lever
and turn
the switch clockwise by 45 degrees to secure it.
CAUTION:
The clearance (C) show in the figure must be within the
specified value.
NOTE:
Fully depressed clutch pedal means a clutch pedal condition
that the clutch pedal lever contacts the pedal stopper rubber.
Position of Clutch Pedal Position Switch
1.
Disconnect the clutch pedal position switch connector.
2.
Loosen the clutch pedal position switch 45 degrees counterclockwise.
3.
Press-fit the clutch pedal position switch
until the clutch pedal
position switch hits the clutch pedal lever
45 degrees clock-
wise while pulling the pedal pad slightly.
CAUTION:
The clearance (C) show in the figure must be within the
specified value.
Clearance :
JSDIA5611ZZ
Clearance :
JSDIA5611ZZ
Clearance :
JSDIA5611ZZ
Clearance :
JSDIA5611ZZ
CLUTCH FLUID
CL-11
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
CLUTCH FLUID
Inspection
INFOID:0000000010745321
FLUID LEAKAGE
• Check clutch line for cracks, deterioration or other damage. Replace any damaged parts.
• Check for fluid leakage by fully depressing clutch pedal while engine is running.
CAUTION:
If leakage occurs around joints, reinstall the joints or, if necessary, replace damaged parts.
FLUID LEVEL
• Check that the fluid level in the reservoir tank is within the specified
range (MAX – MIN lines).
• Visually check for any clutch fluid leakage around the reservoir
tank.
• Check the clutch system for any leakage if the fluid level is
extremely low (lower than MIN).
Draining
INFOID:0000000010745322
CAUTION:
Keep painted surface on the body or other parts free of clutch fluid. If it spills, wipe up immediately
and wash the affected area with water.
1.
Connect a transparent vinyl hose
to air bleeder of bleeding
connector .
2.
Press the lock pin
into the bleeding connector
, and main-
tain the position.
SFIA2634J
JSDIA5568ZZ
JPDIB0041ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст