Nissan Terrano r20e. Manual — part 377
CHECKING SEAT BELTS, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS
NMA059
CHASSIS AND BODY MAINTENANCE
Body (Cont’d)
MA-46
Checking Body Corrosion
Visually check the body sheet metal panel for corrosion, paint damage (scratches, chipping, rubbing, etc.) or
damage to the anti-corrosion materials. In particular, check the following locations.
Hemmed portion
Hood front end, door lower end, trunk lid rear end, etc.
Panel joint
Side sill of rear fender and center pillar, rear wheel housing of rear fender, around strut lower in engine
compartment, etc.
Panel edge
Trunk lid opening, sun roof opening, fender wheel-arch flange, fuel filler lid flange, around holes in panel, etc.
Parts contact
Waist moulding, windshield moulding, bumper, etc.
Protectors
Damage or condition of mudguard, fender protector, chipping protector, etc.
Anti-corrosion materials
Damage or separation of anti-corrosion materials under the body.
Drain holes
Condition of drain holes at door and side sill.
When repairing corroded areas, refer to the Corrosion Repair Manual.
CHASSIS AND BODY MAINTENANCE
MA-47
Engine Maintenance
INSPECTION AND ADJUSTMENT
Drive belt deflection
Unit: mm (in)
Used belt deflection
Deflection of
new belt
Limit
Deflection after
adjustment
Engine
TD27Ti
TD27Ti
TD27Ti
Alternator
20
(0.79)
11 - 13
(0.43 - 0.51)
9 - 11
(0.35 - 0.43)
Air conditioner
12
(0.47)
6 - 7.5
(0.236 - 0.295)
5 - 6.5
(0.197 - 0.256)
Power steering
oil pump
15
(0.59)
8 - 9.5
(0.315 - 0.374)
7 - 8.5
(0.276 - 0.335)
Applied pushing
force
98 N (10 kg, 22 lb)
Oil capacity (Refill capacity)
TD27Ti engine
Unit:
(Imp qt)
With oil filter change
6.2 (5-1/2)
Without oil filter change
5.5 (4-7/8)
ZD30DDTi engine
Unit:
(Imp qt)
With oil filter change
6.7 (5-7/8)
Without oil filter change
6.2 (5-1/2)
Cooling system check
Unit: kPa (bar, kg/cm
2
, psi)
Cooling system testing pressure
98 (0.98, 1.0, 14)
Radiator cap relief pressure
78 - 98
(0.78 - 1.0, 0.8 - 1.0, 11 - 14)
Coolant capacity (Refill capacity)
Unit:
(Imp qt)
Engine
TD27Ti
ZD30DDTi
Without reservoir tank
10 (8-3/4)
10.6 (9-3/8)
Reservoir tank
0.8 (3/4)
0.75 (5/8)
Valve clearance (Hot)
Unit: mm (in)
Engine
TD27Ti
Intake
0.25 (0.0098)
Exhaust
Injection nozzle
Unit: kPa (bar, kg/cm
2
, psi)
Engine
TD27Ti
Initial injection pressure
New
12,259 - 12,749 (122.6 - 127.5, 125 -
130, 1,778 - 1,849)
Used
12,749 - 13,730 (127.5 - 137.3, 130 -
140, 1,849 - 1,991)
Idle speed
Unit: rpm
Engine
TD27Ti
With A/C
850±50
Without A/C
700±50
SERVICE AND SPECIFICATIONS (SDS)
MA-48
Chassis and Body Maintenance
INSPECTION AND ADJUSTMENT
Clutch
Unit: mm (in)
Vehicle model
All
Pedal free height
RHD
210 - 220
(8.27 - 8.66)
LHD
227 - 237
(8.94 - 9.33)
Pedal free play
1.0 - 3.0 (0.039 - 0.118)
Pedal free travel
155 - 160 (6.10 - 6.30)
Front axle and front suspension
(Unladen)*1
Unit: degree
Model
H/T VAN
H/T
WAGON
Camber
0°30
′
±30
′
Caster
0°29
′
±30
′
0°30
′
±30
′
0°30
′
±30
′
Kingpin inclination
12°37
′
Toe-in
A-B
mm (in)
3.5 - 5.5
(0.14 - 0.22)
3 - 5
(0.12 - 0.20)
3 - 5
(0.12 - 0.20)
Front wheel turning
angle (degrees)
(Full turn)*2
Inside
34°27
′
Outside
33°38
′
*1: Fuel, radiator coolant and engine oil full.
Spare tire, jack, hand tools and mats in designated positions.
*2: Wheel turning force (at circumference of steering wheel) of 98 to
147 N (10 to 15 kg, 22 to 33 lb) with engine idle.
Brake
Disc brake
mm (in)
LD28VA
Pad
Standard thickness
15.5 (0.61)
Minimum thickness
2.0 (0.079)
Rotor
Standard thickness
2.60 (1.02)
Minimum thickness
24.0 (0.94)
Drum brake
mm (in)
LT28
Lining
Standard thickness
Leading
8.95 (0.352)
Trailing
3.95 (0.156)
Minimum thickness
1.52 (0.06)
Drum
Standard diameter
280 (11.02)
Maximum diameter
282 (11.10)
Pedal
mm (in)
RHD
LHD
Free height
196 - 206
(7.7 - 8.1)
210 - 220
(8.3 - 8.7)
Free play
1.0 - 3.0 (0.039 - 0.118)
Full stroke
137.7 - 148.7
(5.42 - 5.85)
142.5 - 152.5
(5.61 - 6.00)
Parking brake
Number of notches [at pulling
force 196 N (20 kg, 44 lb)]
9 - 10
SERVICE AND SPECIFICATIONS (SDS)
MA-49
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст