Nissan Titan. Manual — part 136
DLN-116
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
TRANSFER ASSEMBLY
41. Install the transfer control device to the rear case.
a. Turn the control shift rod fully counterclockwise using a suitable
tool, and then put a mark on the control shift rod.
b. Align the transfer control device shaft cutout with the mark on
the control shift rod, and install it.
NOTE:
Turn the transfer control device when the transfer control device
connection does not match.
c.
Tighten the bolts to the specified torque. Refer to
42. Install the drain plug and filler plug with new gaskets to the rear case. Tighten to the specified torque.
DLN-101, "Disassembly and Assembly"
CAUTION:
Do not reuse gaskets.
PDIA0119E
PDIA0120E
SDIA2212E
PLANETARY CARRIER
DLN-117
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PLANETARY CARRIER
Disassembly and Assembly
INFOID:0000000009886040
DISASSEMBLY
1. Remove the snap ring.
2. Remove the sun gear assembly from the planetary carrier
assembly using suitable tool.
3. Remove the snap ring from the sun gear assembly using suit-
able tool.
CAUTION:
Do not reuse snap ring.
4. Remove the carrier bearing from the sun gear using Tools.
5. Remove the needle bearing from the sun gear using Tool.
SDIA2792E
SDIA2353E
Tool number
(A): ST35300000 ( — )
(B): ST30021000 (J-22912-01)
SDIA2149E
Tool number
: ST33710000 ( — )
SDIA2354E
DLN-118
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
PLANETARY CARRIER
6. Remove the metal bushing from the sun gear using Tools.
INSPECTION AFTER DISASSEMBLY
Bearing
Check the bearing for damage and rough rotation. If necessary,
replace the bearing with a new one.
Planetary Carrier
• Measure the end play of each pinion gear. If it is out of specifica-
tion, replace the planetary carrier assembly with new one.
• Check the working face of each gear and bearing for damage,
burrs, partial wear, dents and other abnormality. If any is found,
replace the planetary carrier assembly with a new one.
Sun Gear
• Check if the oil passage of the sun gear assembly is clogged. For
this, try to pass a 3.6 mm (0.142 in) dia. wire through the oil pas-
sage as shown.
• Check the sliding and contact surface of each gear and bearing for
damage, burrs, partial wear, dents and other abnormality. If any is
found, replace the sun gear assembly with a new one.
Internal Gear
Tool number
(A): ST33710000 ( — )
(B): ST35325000 ( — )
(C): ST33290001 (J-34286)
SDIA2168E
MTF0041D
Pinion gear end play
: 0.1 - 0.7 mm (0.004 - 0.028 in)
PDIA0146E
PDIA0147E
PLANETARY CARRIER
DLN-119
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Check the internal gear teeth for damage, partial wear, dents or
other abnormality. If any is found, replace the internal gear with a
new one.
ASSEMBLY
1. Apply ATF to the new metal bushing, then install the new metal
bushing until it becomes Dimension (A) using Tool.
CAUTION:
Do not reuse metal bushing.
2. Apply ATF to the new needle bearing, then install the new nee-
dle bearing until it becomes Dimension (B) using Tool.
CAUTION:
Do not reuse needle bearing.
3. Install the carrier bearing to the sun gear using Tools.
4. Install the new snap ring to the sun gear assembly using suitable
tool.
CAUTION:
Do not reuse snap ring.
PDIA0157E
Tool number
: ST35300000 ( — )
Dimension (A)
: 7.7 - 8.3mm (0.303 - 0.327in)
SDIA3189E
Tool number
: ST33220000 ( — )
Dimension (B)
: 62.5 - 63.1mm (2.461 - 2.484in)
SDIA3190E
Tool number
(A): ST30720000 (J-25405)
(B): ST27863000 ( — )
PDIA0149E
SDIA2353E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст