Nissan Xterra. Manual — part 491
ENGINE OIL
LU-7
< PERIODIC MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
PERIODIC MAINTENANCE
ENGINE OIL
Inspection
INFOID:0000000009484418
OIL LEVEL
• Before starting the engine make sure the vehicle is parked on a flat
and level surface, then check the oil level. If the engine is already
running, turn it off and allow 10 minutes before checking.
• Pull out oil level gauge and wipe clean.
• Insert oil level gauge.
• Check that the oil level is within the low (L) and high (H) range as
indicated on the dipstick.
• If the engine oil level is out of range, add oil as necessary. Refer to
MA-12, "Fluids and Lubricants"
.
CAUTION:
Do not overfill the engine with oil.
OIL APPEARANCE
• Check the engine oil for a white milky appearance or excessive contamination.
• If the engine oil is milky, it is highly probable that it is contaminated with engine coolant. Repair or replace
damaged parts.
OIL LEAKAGE
Check for oil leakage around the following areas:
• Oil pans (lower and upper)
• Oil pan drain plug
• Oil pressure switch
• Oil filter
• Oil cooler
• Intake valve timing control cover
• Intake valve timing control solenoid valve
• Water pump cover
• Chain tensioner cover
• Intake valve timing control cover and intake valve timing control solenoid valve
• Mating surface between cylinder block and cylinder head
• Mating surface between lower cylinder block and cylinder block
• Mating surface between cylinder head and rocker cover
• Mating surface between front timing chain case and rear timing chain case
• Mating surface between rear timing chain case and cylinder head
• Mating surface between rear timing chain case and cylinder block
• Mating surface between rear timing chain case and lower cylinder block
• Mating surface between rear timing chain case and oil pan (upper)
• Crankshaft oil seals (front and rear)
• Oil level gauge guide
• Camshaft position sensor (PHASE)
OIL PRESSURE CHECK
WARNING:
• Be careful not to burn yourself, as the engine and engine oil may be hot.
• Put the shift selector in the Park (P) position (A/T models) or Neutral position (M/T models), and
apply parking brake securely.
1. Check engine oil level. Refer to
.
2. Remove engine under cover. Refer to
EXT-15, "Removal and Installation"
.
PBIC2823E
LU-8
< PERIODIC MAINTENANCE >
[VQ40DE]
ENGINE OIL
3. Disconnect the oil pressure switch (B) harness connector.
• A: Oil pan (upper)
•
: Front
4. Remove the oil pressure switch (B) using suitable tool.
CAUTION:
Do not drop or shock oil pressure switch.
5. Install Tools.
6. Start the engine and warm it up to normal operating temperature.
7. Check the engine oil pressure with engine running under no-load. Refer to
CAUTION:
If the difference between the test results and the specification is extreme, check the oil passages
and oil pump for leaks and blockages.
8. After the inspections, install oil pressure switch as follows:
a. Remove old liquid gasket adhering to oil pressure switch and engine.
b. Apply liquid gasket and tighten oil pressure switch to the specification.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-21, "Recommended Chemical Prod-
.
c.
After warming up engine, ensure there are no engine oil leaks.
9. Install the engine under cover. Refer to
EXT-15, "Removal and Installation"
Changing Engine Oil
INFOID:0000000009484419
WARNING:
• Be careful not to burn yourself, as the engine and engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer; try to avoid direct skin
contact with used oil. If skin contact is made, wash thoroughly with soap or hand cleaner as soon as
possible.
1. Warm up the engine, and check for oil leaks.
2. Stop the engine and wait for at least 10 minutes.
3. Remove the oil drain plug and oil filler cap to drain the old oil.
4. Install a new copper sealing washer on the oil drain plug, then install the oil drain plug in the oil pan.
CAUTION:
• Clean the drain plug.
• Do not reuse copper sealing washer.
5. Refill the engine with new specified engine oil.
WBIA0813E
Tool numbers : ST25051001 (J-25695-1)
: ST25052000 (J-25695-2)
WBIA0571E
Oil pressure switch torque
: 14.7 N·m (1.5 kg-m, 11 ft-lb)
Oil drain plug
: Refer to
EM-34, "Removal and Installation"
.
ENGINE OIL
LU-9
< PERIODIC MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
CAUTION:
The refill capacity depends on the oil temperature and drain time. Use the “Refill oil capacity” val-
ues as a reference and check the oil level using the dipstick when filling the engine with oil.
6. Warm up the engine and check the area around the drain plug and oil filter for oil leaks. Repair as neces-
sary.
7. Stop the engine and wait for more than 10 minutes.
8. Check the oil level using the dipstick as shown. Add oil as nec-
essary and install the oil filler cap. Refer to
CAUTION:
Do not overfill the engine with oil.
Oil grade and viscosity
: Refer to
MA-12, "Fluids and Lubricants"
.
Oil capacity
: Refer to
MA-12, "Fluids and Lubricants"
.
PBIC2823E
LU-10
< PERIODIC MAINTENANCE >
[VQ40DE]
OIL FILTER
OIL FILTER
Removal and Installation
INFOID:0000000009484420
REMOVAL
1. Remove the engine under cover access door. Refer to
EXT-15, "Removal and Installation"
.
2. Drain engine oil. Refer to
3. Remove the oil filter using Tool as shown.
WARNING:
Be careful not to burn yourself, as the engine and engine oil
may be hot.
CAUTION:
• Oil filter is equipped with a pressure relief valve.
• Use Genuine NISSAN Oil Filter or equivalent.
• When removing, position a shop cloth to absorb any
engine oil leaks or spills.
• Do not allow engine oil to adhere to drive belts.
• Completely wipe off any engine oil that adheres to the engine and the vehicle.
INSTALLATION
1. Remove foreign materials adhering to the oil filter seal mating surface.
2. Apply clean engine oil to the new oil filter seal as shown.
3. Screw on the oil filter manually until it touches the installation
surface, then tighten it by 2/3 turn as shown. Or tighten to speci-
fication.
4. Refill engine with new engine oil. Refer to
.
5. Inspect the engine for oil leaks. Repair as necessary.
6. Install the engine under cover access door. Refer to
EXT-15, "Removal and Installation"
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to
.
2. Start the engine and check for engine oil leaks. Repair as necessary.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level and add engine oil as required.
Tool number
: KV10115801 (J-38956)
LBIA0425E
SMA010
Oil filter
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
SMA702C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст