Qashqai J11. Door & Lock — part 12
FUEL FILLER LID OPENER
DLK-193
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2.
Remove fuel mounting pin (1).
3.
Remove fixing screws, and then remove fuel filler lid assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• After installation, apply the touch-up paint (the body color) onto the head of the fixing screws.
• Apply anti-corrosion wax to mounting surface of fixing screw and fuel filler lid to prevent rust.
NOTE:
The following table shows the specified values for checking normal installation status.
Unit: mm [in]
FUEL FILLER LID LOCK
FUEL FILLER LID LOCK : Removal and Installation
INFOID:0000000010434742
REMOVAL
1.
Fully open fuel filler lid.
2.
Remove luggage lower finisher RH. Refer to
.
3.
In the order of 1
→
2 as shown in the figure, rotate and disengage
fuel filler lid lock assembly, and then remove fuel filler lid lock
assembly.
NOTE:
Operation is performed easily when rotating fuel filler lid lock
from passenger room side.
4.
In the order of 1
→
4 as shown in the figure. Disengage fuel filler
lid opener cable (1). Remove fuel filler lid opener cable while
pressing stopper pin (2).
JMKIB3183ZZ
Clearance
Evenness
Fuel filler lid – Body side outer
3.7 – 5.3
(0.146 – 0.209)
(-1.0) – (+1.0)
[(-0.039) – (+0.039)]
: Pawl
: Vehicle front
JMKIB1094ZZ
JMKIA5719ZZ
DLK-194
< REMOVAL AND INSTALLATION >
[TYPE 1]
FUEL FILLER LID OPENER
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation
INFOID:0000000010434741
REMOVAL
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Disconnect fuel opener cable (2) from fuel filler lid opener lever
(1) according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
3.
Remove front kicking plate inner RH and rear kicking plate inner RH. Refer to
.
4.
Remove dash side finisher RH. Refer to
INT-18, "Removal and Installation"
5.
Remove center pillar lower garnish RH. Refer to
INT-18, "Removal and Installation"
.
6.
Remove luggage side lower finisher RH. Refer to
.
7.
Disconnect fuel opener cable from fuel filler lid lock assembly. Refer to
LOCK : Removal and Installation"
.
8.
Remove fuel opener cable from each harness protector.
9.
Remove cable protector.
10. Remove fuel opener cable fixing clips, and then remove fuel opener cable.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never reuse cable protector. Always replace it with a new one when it is removed.
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
JMKIA5672ZZ
DOOR SWITCH
DLK-195
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR SWITCH
Removal and Installation
INFOID:0000000010434743
REMOVAL
Remove the TORX bolt (A), and then remove door switch (1).
INSTALLATION
Install in the reverse order of removal.
JMKIA2173ZZ
DLK-196
< REMOVAL AND INSTALLATION >
[TYPE 1]
INSIDE KEY ANTENNA
INSIDE KEY ANTENNA
CONSOLE
CONSOLE : Removal and Installation
INFOID:0000000010434745
REMOVAL
1.
Remove the console rear finisher. Refer to
IP-19, "Removal and Installation"
2.
Remove the inside key antenna (console) mounting screw
,
and then remove inside key antenna (console)
.
INSTALLATION
Install in the reverse order of removal.
LUGGAGE ROOM
LUGGAGE ROOM : Removal and Installation
INFOID:0000000010434746
REMOVAL
Remove the mounting clip
, and then remove inside key antenna
(luggage room)
.
INSTALLATION
Install in the reverse order of removal.
JMKIB3257ZZ
JMKIB3258ZZ
OUTSIDE KEY ANTENNA
DLK-197
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OUTSIDE KEY ANTENNA
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000010434747
REMOVAL
Remove the outside handle grip. Refer to
DLK-183, "OUTSIDE HANDLE : Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
REAR BUMPER
REAR BUMPER : Removal and Installation
INFOID:0000000010434749
REMOVAL
1.
Remove the rear bumper fascia assembly. Refer to
EXT-24, "Removal and Installation"
.
2.
Disconnect outside key antenna (rear bumper) connector, and
then remove outside key antenna (rear bumper)
.
INSTALLATION
Install in the reverse order of removal.
JMKIB3259ZZ
DLK-198
< REMOVAL AND INSTALLATION >
[TYPE 1]
INTELLIGENT KEY WARNING BUZZER
INTELLIGENT KEY WARNING BUZZER
Removal and Installation
INFOID:0000000010434750
REMOVAL
1.
Remove the front bumper fascia assembly. Refer to
EXT-20, "Removal and Installation"
2.
Disconnect Intelligent Key warning buzzer connector.
3.
Remove the Intelligent Key warning buzzer mounting bolt
, and
then remove the Intelligent Key warning buzzer
.
INSTALLATION
Install in the reverse order of removal.
JMKIB2758ZZ
INTELLIGENT KEY BATTERY
DLK-199
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INTELLIGENT KEY BATTERY
Removal and Installation
INFOID:0000000010434751
1.
Release the lock knob at the back of the Intelligent Key and remove the mechanical key.
2.
Insert a flat-blade screwdriver (A) wrapped with a cloth into the
slit of the corner and twist it to separate the upper part from the
lower part.
CAUTION:
• Do not touch the circuit board or battery terminal.
• The key fob is water-resistant. However, if it does get wet,
immediately wipe it dry.
3.
Replace the battery with new one.
4.
Align the tips of the upper and lower parts, and then push them
together until it is securely closed.
CAUTION:
• When replacing battery, keep dirt, grease, and other for-
eign materials off the electrode contact area.
• After replacing the battery, check that all Intelligent Key
functions work normally.
PIIB6221E
Battery replacement
:Coin-type lithium battery
(CR2032)
PIIB6222E
DLK-200
< HOW TO USE THIS MANUAL >
[TYPE 2]
APPLICATION NOTICE
HOW TO USE THIS MANUAL
APPLICATION NOTICE
Information
INFOID:0000000010434752
Check the vehicle type to use the service information in this section.
Service information
Destination
Type 1
For Europe
With Intelligent Key and super lock
Type 2
• For Europe
• For South Africa
• For Russia, Ukraine and Kazakhstan
With Intelligent Key, without super lock
Type 3
For Europe
Without Intelligent Key, with super lock
Type 4
• For Europe
• For South Africa
• For Russia, Ukraine and Kazakhstan
Without Intelligent Key and super lock
Type 5
• For Australia
• For General export
With Intelligent Key, without super lock
Type 6
• For Australia
• For General export
Without Intelligent Key and super lock
PRECAUTIONS
DLK-201
< PRECAUTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010434753
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000010479688
CAUTION:
Comply with the following cautions to prevent any error and malfunction.
• Before removing and installing any control units, first turn the ignition power source and accessory
power source to the OFF, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect
both battery cables.
• Always use CONSULT to perform self-diagnosis as a part of each function inspection after finishing
work. If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Open driver door.
3.
Turn the ignition switch to the ON position.
(At this time, the steering lock will be released.)
4.
Turn the ignition switch to OFF position with driver door open.
5.
Wait for 3 minutes or longer with driver door open.
NOTE:
• Do not close driver door because the steering wheel locks when driver door is closed.
DLK-202
< PRECAUTION >
[TYPE 2]
PRECAUTIONS
• The auto acc function is adapted to this vehicle. For this reason, even when the ignition switch is turned
to OFF position, the accessory power source does not turned OFF and continues to be supplied for a
certain amount of time.
6.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
7.
Perform the necessary repair operation.
8.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from OFF position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
9.
Perform self-diagnosis check of all control units using CONSULT.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000010434755
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
Precautions for Removing Battery Terminal
INFOID:0000000010503428
• With the adoption of Auto ACC function, ACC power is automatically supplied by operating the intelligent key
or remote keyless entry or by opening/closing the driver side door. In addition, ACC power is supplied even
after the ignition switch is turned to the OFF position, i.e. ACC power is supplied for a certain fixed time.
• When disconnecting the 12V battery terminal, turn off the ACC
power before disconnecting the 12V battery terminal, observing
“How to disconnect 12V battery terminal” described below.
NOTE:
Some ECUs operate for a certain fixed time even after ignition
switch is turned OFF and ignition power supply is stopped. If the
battery terminal is disconnected before ECU stops, accidental DTC
detection or ECU data damage may occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
HOW TO DISCONNECT 12V BATTERY TERMINAL
Disconnect 12V battery terminal according to instruction described below.
1.
Open the hood.
2.
Turn ignition switch to the ON position.
3.
Turn ignition switch to the OFF position with the driver side door opened.
4.
Get out of the vehicle and close the driver side door.
5.
Wait at least 3 minutes. For vehicle with the engine listed below, remove the battery terminal after a lapse
of the specified time.
PIIB3706J
SEF289H
D4D engine
: 20 minutes
HRA2DDT
: 12 minutes
K9K engine
: 4 minutes
M9R engine
: 4 minutes
PRECAUTIONS
DLK-203
< PRECAUTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CAUTION:
While waiting, never operate the vehicle such as locking, opening, and closing doors. Violation of
this caution results in the activation of ACC power supply according to the Auto ACC function.
6.
Remove 12V battery terminal.
CAUTION:
After installing 12V battery, always check self-diagnosis results of all ECUs and erase DTC.
Work
INFOID:0000000010434757
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operational.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
R9M engine
: 4 minutes
V9X engine
: 4 minutes
DLK-204
< PREPARATION >
[TYPE 2]
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000010434758
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls, and metal clips
Power tool
SIIA0995E
JMKIA3050ZZ
PIIB1407E
COMPONENT PARTS
DLK-205
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000010434759
1.
Front door lock assembly (passenger
side)
2.
SYSTEM : Component Parts Loca-
tion"
3.
Push-button ignition switch
4.
Combination meter
5.
Front power window switch (passen-
ger side) (door lock and unlock switch)
6.
Door switch
7.
Door lock assembly
8.
Back door lock assembly
9.
Back door opener switch assembly
10. Inside key antenna (luggage room)
11.
Inside key antenna (console)
12. Indicator unit (door lock status indica-
tor)
13. Intelligent Key warning buzzer
14. Outside key antenna
15. Door request switch
16. Outside antenna (rear bumper)
A.
View with luggage room
B.
View with center console assembly re-
moved
C.
View with instrument panel
D.
View with front bumper removed
E.
View with door panel
F.
View with rear bumper removed
JMKIB3270ZZ
DLK-206
< SYSTEM DESCRIPTION >
[TYPE 2]
COMPONENT PARTS
Component Description
INFOID:0000000010434760
Item
Function
Door lock and unlock switch
• Transmits door lock/unlock operation to BCM.
• Integrated in the power window main switch and center console assembly.
Combination meter
• Performs operation method guide and warning with buzzer.
• Transmits vehicle speed signal to CAN communication line.
Push-button ignition switch
• BCM transmits the change in the power supply position with the push-button ignition switch
to IPDM E/R via CAN communication line. IPDM E/R transmits the power supply position
status via CAN communication line to BCM.
• Immobilizer antenna amp checks Intelligent Key transponder.
BCM
BCM detects the vehicle status according to signals from each door switch and each outside/
inside key antenna. BCM transmits drive signal to door lock actuator when BCM receives op-
eration signal from remote keyless entry receiver and each switch.
Refer to
BCS-6, "BODY CONTROL SYSTEM : Component Parts Location"
for detailed in-
stallation location.
Door lock actuator
• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.
Door request switch
• Transmits door lock/unlock operation to BCM.
• Integrated in the outside handle (driver side, passenger side and back door).
Door switch
Detects door open/close condition.
Inside key antenna
• Detects whether Intelligent Key is inside the vehicle.
• Installed in the instrument center, consol and luggage room.
Intelligent Key warning buzzer
Warns for an inappropriate operation.
Outside key antenna
• Detects whether Intelligent Key is outside the vehicle.
• Integrated in the outside handle.
Intelligent Key
The following functions are available when having and carrying electronic ID.
• Door lock/unlock
• Engine start
• Remote control entry function is available when operating on button.
Unlock sensor
Built-in in driver side door lock assembly
• Detects door lock condition of driver door
SYSTEM (POWER DOOR LOCK SYSTEM)
DLK-207
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SYSTEM (POWER DOOR LOCK SYSTEM)
System Diagram
INFOID:0000000010434761
System Description
INFOID:0000000010434762
DOOR LOCK FUNCTION
Door Lock and Unlock Switch
• The door lock and unlock switch (driver side) is built into power window main switch.
• The door lock and unlock switch (passenger side) is built into front power window switch (passenger side).
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors actu-
ator are unlocked.
Unlock Sensor
• BCM locks all doors or unlocks all doors, when driver door lock knob is operated.
• With the mechanical key inserted in the door key cylinder on driver side, turning it to lock position, locks door
lock actuator of all doors.
• With the mechanical key inserted in the door key cylinder on driver side, turning it to unlock position, unlocks
door lock actuator of all doors.
Operation Condition
If all of the following conditions are satisfied, door lock and unlock operation is performed using the door lock
and unlock switch.
INTERIOR ROOM LAMP CONTROL FUNCTION
Interior room lamp is controlled according to door lock /unlock state, refer to
CONTROL SYSTEM : System Description"
AIR BAG INTERLOCK UNLOCK FUNCTION
When ignition switch is ON and BCM receives shock status signal, it operates automatically to unlock all
doors. Air bag diagnosis sensor unit sends the shock status signal to BCM via CAN communication.
IGNITION POSITION WARNING FUNCTION
All doors are locked once, but BCM immediately unlocks all doors, according to driver door lock status
detected by unlock sensor, when door lock operation is performed, driver door is open, and ignition position is
ON.
DOOR LOCK STATUS INDICATOR OPERATION
JMKIB2435GB
Door lock and unlock switch operation
Operation condition
LOCK/UNLOCK
• Doors are not locked by Intelligent Key, door request switch
and auto door lock function
• Ignition position warning function is not activated
DLK-208
< SYSTEM DESCRIPTION >
[TYPE 2]
SYSTEM (POWER DOOR LOCK SYSTEM)
The door lock status indicator indicates door lock status under the following condition.
UNLOCK LINK FUNCTION
When driver door or passenger door is opened using the override function, all doors are unlocked.
Unlock function operates when driver door or passenger door is open while all of the following conditions are
satisfied.
NOTE:
When anti-hijack function is activated, only the applicable door is unlocked.
Indicator operation
Ignition position
Door status
Lock operation
ON (30 minutes timer)
OFF
All doors are closed and door
is locked
Door lock and unlock switch
ON
ON
All doors are closed and door
is locked
Door lock and unlock switch
ON (1 minute timer)
OFF
All doors are closed and door
is locked
Intelligent Key, door request
switch or auto door lock func-
tion
ON
ON
All doors are closed and door
is locked
Intelligent Key, door request
switch or auto door lock func-
tion
ON
→
OFF
–
(All doors are closed
→
any
door is open) or (All doors are
locked
→
any door is un-
locked)
–
ON (timer is running)
→
ON
(timer is stop)
OFF
→
ON
–
–
ON
→
ON (30 minutes timer)
ON
→
OFF
–
Door lock and unlock switch
ON
→
ON (1 minute timer)
ON
→
OFF
–
Intelligent Key, door request
switch or auto door lock func-
tion
Operation condition
• Doors are locked by door lock/unlock switch or by automatic lock/unlock function
• Driver or passenger door switch is switched from OFF to ON
• Anti-hijack function is not activated
• Vehicle speed is 5 km/h (3 MPH) or less
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст