Nissan March K13. Manual — part 649
SIDE OIL SEAL
TM-13
< REMOVAL AND INSTALLATION >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
SIDE OIL SEAL
Removal and Installation
INFOID:0000000006056566
REMOVAL
1.
Remove front drive shafts. Refer to
FAX-17, "Removal and Installation"
.
2.
Remove differential side oil seals (1) from clutch housing and
transaxle case, using a suitable tool.
CAUTION:
Never damage transaxle case and clutch housing.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install differential side oil seals (1) to clutch housing and transaxle
case, using the drift [Stamping number: B.vi 1666-B] of the drift set
[SST: KV32500QAA].
CAUTION:
• Never incline differential side oil seal.
• Never damage clutch housing and transaxle case.
Inspection
INFOID:0000000006056567
INSPECTION AFTER INSTALLATION
Check the oil level and oil leakage. Refer to
.
JPDIC0118ZZ
B
: Transaxle case side
C
: Clutch housing side
Dimension “L
1
”
: 5.7 – 6.3 mm (0.224 – 0.248 in)
Dimension “L
2
”
: 2.4 – 3.0 mm (0.094 – 0.118 in)
JPDIC0401ZZ
TM-14
< REMOVAL AND INSTALLATION >
[5MT: RS5F91R]
POSITION SWITCH
POSITION SWITCH
Removal and Installation
INFOID:0000000006056568
REMOVAL
1.
Drain gear oil. Refer to
.
2.
Disconnect position switch connector (A).
3.
Remove position switch from transaxle case.
INSTALLATION
1.
Apply recommended sealant to threads of position switch.
• Use Genuine Liquid Gasket, Three Bond 1215 or an equivalent.
CAUTION:
Remove old sealant and oil adhering to threads.
2.
Install position switch to transaxle case.
3.
Tighten position switch to the specified torque. Refer to
4.
Refill gear oil. Refer to
Inspection
INFOID:0000000006056569
INSPECTION AFTER INSTALLATION
• Check continuity between position switch terminals. Refer to
TM-10, "BACK-UP LAMP SWITCH : Compo-
TM-10, "PARK/NEUTRAL POSITION (PNP) SWITCH : Compo-
(PNP switch).
• Check the oil leakage and the oil level. Refer to
.
JPDIC0733ZZ
CONTROL LINKAGE
TM-15
< REMOVAL AND INSTALLATION >
[5MT: RS5F91R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL LINKAGE
Exploded View
INFOID:0000000006056570
Removal and Installation
INFOID:0000000006056571
REMOVAL
1.
Shift the shifter lever to the neutral position.
2.
Remove air duct (inlet), air cleaner body assembly, and air cleaner cover assembly. Refer to
3.
Pull out and disconnect the each cable from the shifter lever A and the selector lever, using a suitable
remover.
4.
While pressing the lock of the selector cable in the direction of
the arrow shown in the figure, remove the selector cable from
the cable mounting bracket.
5.
While pressing the lock of the shifter cable in the direction of the
arrow shown in the figure, remove the shifter cable from the
cable mounting bracket.
6.
Remove cable mounting bracket from clutch housing.
7.
Pull the shifter lever knob upward to remove.
8.
Remove center console assembly. Refer to
.
9.
Pull out and disconnect the each cable from the control device,
using a suitable remover.
1.
Shifter lever A
2.
Selector lever
3.
Selector cable
4.
Shifter cable
5.
Cable mounting bracket
6.
Tapping bolt
7.
Bracket
8.
Grommet
9.
Control device
10. Shifter lever
11.
Shifter lever knob
Refer to
for the symbols in the figure.
JPDIC0789GB
JPDIC0793ZZ
TM-16
< REMOVAL AND INSTALLATION >
[5MT: RS5F91R]
CONTROL LINKAGE
10. While pressing the lock of the selector cable in the direction of
the arrow shown in the figure, remove the selector cable from
the control device.
11. While pressing the lock of the shifter cable in the direction of the
arrow shown in the figure, remove the shifter cable from the con-
trol device.
12. Remove the control device.
13. Remove center muffler, exhaust front tube, and heat plate. Refer
EX-5, "Removal and Installation"
14. Remove the bracket from the vehicle.
15. Remove the grommet and then remove the shifter cable and
selector cable from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Install each cable without causing interference with other parts, a 120 mm (4.72 in)-or-less bend, and
a 180-degrees-or-more twist.
• Install boot of each cable without causing interference with other parts and a 90-degrees-or-more
twist.
• Fit boot of to center console assembly the groove on shifter lever knob.
• To install the shifter lever knob, press it into the shifter lever.
CAUTION:
• Never reuse shifter lever knob.
• Be careful with orientation of shifter lever knob.
• Tapping work for tapping bolts is not applied to new clutch housing. Do not perform tapping by other than
screwing tapping bolts because tapping is formed by screwing tapping bolts into clutch housing.
CAUTION:
Never reuse tapping bolt.
• Insert the each cable until it reaches the cable mounting bracket.
• Insert the each cable until it reaches the shifter lever A and the selector lever.
• Shift the shifter lever to the neutral position.
Inspection
INFOID:0000000006056572
INSPECTION AFTER INSTALLATION
Shifter lever knob
Check that the shifter lever knob is installed in the right position.
Shifter cable and selector cable
• Pull each cable in the removal direction to check that it dose not disconnect from the cable mounting
bracket.
• Pull each cable in the removal direction to check that it dose not disconnect from the control device.
• Pull grommet in the removal direction to check that it dose not disconnect from the vehicle.
Shifter lever
• Check that there is no tangle, hook, abnormal sound, looseness, and interference when the shifter lever is
moved to each position. If there is a malfunction, then repair or replace the malfunctioning part.
• Check that the shifter lever smoothly returns to the neutral position after moving the lever from 1st to 2nd
gear and moving hands off the lever. If there is a malfunction, then repair or replace the malfunctioning part.
• Check that the shifter lever smoothly returns to the neutral position after moving the lever from 5th to the
reverse gear position and moving hands off the lever. If there is a malfunction, then repair or replace the mal-
functioning part.
JPDIC0793ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст