Nissan Teana J32. Manual — part 755
INT-40
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
2.
Remove front pillar garnish mounting clip and metal clip with a
remover tool (A), and then remove front pillar garnish (1).
DASH SIDE FINISHER
1.
Remove front kicking plate inner.
2.
Remove dash side finisher mounting clips and metal clip with a
remover tool (A), and then remove dash side finisher (1).
FRONT KICKING PLATE OUTER
Remove front kicking plate outer mounting pawls with a remover tool
(A), and then remove kicking plate outer (1).
FRONT KICKING PLATE INNER
1.
With a remover tool (A), disengage the metal clips and pawls located in the front, then pull up front kicking
plate inner (1) to remove as shown by the figure below.
REAR KICKING PLATE OUTER
: Clip
: Metal clip
JMJIA1771ZZ
: Clip
: Metal clip
JMJIA1773ZZ
: Pawl
JMJIA1779ZZ
: Pawl
: Metal clip
JMJIA1772ZZ
BODY SIDE TRIM
INT-41
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Remove rear kicking plate outer mounting pawls with a remover tool
(A), and then remove kicking plate outer (1).
REAR KICKING PLATE INNER
1.
Pull up rear kicking plate inner, and disconnect the clip and
pawls with remover tool (A).
2.
Remove rear kicking plate inner (1).
CENTER PILLAR LOWER GARNISH
1.
Remove front and rear kicking plate inner.
2.
Remove center pillar lower garnish mounting clips with a
remover tool (A), and then remove center pillar lower garnish
(1).
FRONT BODY SIDE WELT
1.
Remove front kicking plate inner.
2.
Remove front body side welt.
REAR BODY SIDE WELT
1.
Remove rear kicking plate inner.
2.
Remove rear body side welt.
CENTER PILLAR UPPER GARNISH
1.
Remove center pillar lower garnish.
2.
Remove front seat belt pre-tension fixing anchor bolt. Refer to
.
3.
Remove partially front and rear body side welt.
: Pawl
JMJIA1777ZZ
: Clip
: Pawl
JMJIA1778ZZ
: Clip
JMJIA1775ZZ
INT-42
< ON-VEHICLE REPAIR >
BODY SIDE TRIM
4.
Remove center pillar upper garnish mounting clip and metal clip
with a remover tool (A).
5.
Pull center pillar upper garnish from inside passenger room, disengage the clip by following the steps
shown in the figure below to remove the garnish from the vehicle.
REAR PILLAR FINISHER
1.
Remove rear seat cushion and rear seatback. Refer to
SE-99, "Removal and Installation"
.
2.
Remove rear seat belt pre-tensioner anchor bolt. Refer to
SB-10, "SEAT BELT RETRACTOR : Removal
3.
Remove rear kicking plate inner.
4.
Remove rear body side welt.
5.
Remove pillar finisher mounting clips and metal clips with a
remover tool (A), and then remove pillar finisher (1).
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check that clips are securely fitted in panel holes on body when installing, and then press them in.
: Clip
: Metal clip
JMJIA1776ZZ
1.
Center pillar upper garnish
2.
Center pillar panel
JMJIA1176ZZ
: Clip
: Pawl
: Metal clip
JMJIA1774ZZ
REAR PARCEL SHELF FINISHER
INT-43
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
REAR PARCEL SHELF FINISHER
Exploded View
INFOID:0000000003819224
Removal and Installation
INFOID:0000000003819225
REMOVAL
1.
Remove rear seatback and rear seat cushion. Refer to
SE-99, "Removal and Installation"
.
2.
Remove rear seat belt pre-tensioner anchor bolt. Refer to
SB-10, "SEAT BELT RETRACTOR : Removal
3.
Disengage child anchor cover (1) fixing pawls with a remover
tool (A) and then remove it.
4.
Remove rear pillar finisher (LH/RH). Refer to
INT-39, "Removal and Installation"
1.
Rear sunshade
2.
Child anchor cover
3.
Rear parcel shelf finisher
: Clip
JMJIA1802ZZ
: Pawl
JMJIA1780ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст