Nissan Teana J32. Manual — part 1161
TM-168
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
TRANSAXLE ASSEMBLY
REMOVAL AND INSTALLATION
TRANSAXLE ASSEMBLY
Exploded View
INFOID:0000000003849108
Removal and Installation
INFOID:0000000003849109
WARNING:
Never remove the reservoir tank cap when the engine is hot. Serious burns could occur from high
pressure engine coolant escaping from the reservoir tank.
REMOVAL
1.
Remove the engine, the transaxle assembly and front suspension member. Refer to
.
2.
Lift with hoist and separate engine, transaxle assembly from front suspension member. Refer to
1.
CVT fluid level gauge
2.
CVT fluid charging pipe
3.
O-ring
4.
Transaxle assembly
A.
For tightening torque, refer to
TM-168, "Removal and Installation"
.
for symbols in the figure.
JPDIA0799GB
TRANSAXLE ASSEMBLY
TM-169
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3.
Remove air breather hose. Refer to
4.
Disconnect secondary speed sensor connector. Refer to
5.
Disconnect CVT unit connector.
6.
Disconnect air fuel ratio sensor 1 (bank 2). Refer to
.
7.
Remove crankshaft position sensor (POS). Refer to
8.
Remove CVT fluid charging pipe from transaxle assembly.
9.
Remove transaxle assembly fixing bolts with power tool.
10. Remove transaxle assembly from engine assembly with a hoist.
11. Remove fluid cooler hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Check fitting of dowel pins (
) when installing transaxle
assembly to engine assembly.
When installing transaxle assembly to the engine assembly, attach
the fixing bolts in accordance with the following.
JPDIA0598ZZ
JPDIA0602ZZ
JPDIA0600ZZ
Insertion direction
Transaxle assembly to engine assembly
Engine assembly to tran-
saxle assembly
Bolt position
A
B
C
D
Number of bolts
1
2
2
4
Bolt length
mm (in)
55 (2.17)
39 (1.54)
108 (4.25)
40 (1.57)
Tightening torque
N·m (kg-m, ft-lb)
74.5 (7.6, 55)
50 (4.3, 31)
TM-170
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
TRANSAXLE ASSEMBLY
• When using the drive plate location guide (commercial service tool:
31197CA000) (A), set it to the stud bolts which is used to install it
to the torque converter.
• When not using drive plate location guide, rotate torque converter
so that the stud bolt (B) for mounting the drive plate location guide
of torque converter aligns with the mounting position of service
hole.
• Rotate crankshaft so that the hole (A) for inserting drive plate loca-
tion guide of drive plate aligns with the service hole (B).
NOTE:
When not using drive plate location guide, insert stud bolt of torque
converter into the hole (C) of drive plate, aligning the drive plate
hole position and torque converter.
CAUTION:
Be careful not to strike the drive plate when installing the
torque converter stud bolt.
• Align the position of tightening nuts (
) for drive plate with those
of the torque converter, and temporarily tighten the nuts. Then,
tighten the bolts to the specified torque.
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
• When tightening the nuts for the torque converter after fixing
the crankshaft pulley bolts, confirm the tightening torque of
the crankshaft pulley mounting bolts. Refer to
.
• Rotate crankshaft several turns and check that transaxle rotates freely without binding after con-
verter is installed to drive plate.
• Never reuse O-ring.
• Apply petroleum jelly to O-ring.
Inspection
INFOID:0000000003849110
INSPECTION BEFORE INSTALLATION
After inserting a torque converter to transaxle assembly, check that
distance (A) is within the reference value limit.
INSPECTION AFTER INSTALLATION
Check the following items.
JPDIA0607ZZ
JPDIA0603ZZ
: 51 N·m (5.2 kg-m,38 ft-lb)
SCIA1861E
B
: Scale
C
: Straightedge
Distance A
: Refer to
JPDIA0620ZZ
TRANSAXLE ASSEMBLY
TM-171
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
• CVT fluid leakage and CVT fluid level. Refer to
.
• CVT position. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст