Nissan Sentra. Manual — part 301
DLK-320
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR HANDLE
DOOR HANDLE
FRONT DOOR HANDLE
FRONT DOOR HANDLE : Exploded View
INFOID:0000000009756636
FRONT DOOR HANDLE : Removal and Installation - Inside Handle
INFOID:0000000009756637
REMOVAL
1. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
2. Remove inside handle assembly screws (A) and the inside han-
dle assembly (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check front door lock cables are properly engaged to inside handle.
• After installation, check front door open/close, lock/unlock operation.
FRONT DOOR HANDLE : Removal and Installation - Outside Handle
INFOID:0000000009756638
REMOVAL
1. Fully close front door glass.
2. Remove front door finisher. Refer to
INT-15, "Removal and Installation"
3. Remove front door vapor barrier.
1.
Outside handle bracket
2.
Rear gasket
3.
Front gasket
4.
Outside handle escutcheon
5.
Outside handle
6.
Door key cylinder rod
7.
Inside handle assembly
ALKIA2925ZZ
ALKIA2715ZZ
DOOR HANDLE
DLK-321
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4. Remove front door glass channel rear.
5. Disconnect the harness connectors from the door antenna and door request switch and then remove har-
ness clamp on outside handle bracket.
6. Remove door side grommet, and loosen screw that retains the
front door outside handle bracket.
7. Reach in to separate door key cylinder rod (LH side) (1) from
door key cylinder assembly (LH side).
8. While pulling outside handle (1), remove door key cylinder
assembly (LH side) or outside handle escutcheon (2) (RH side).
9. While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
JMKIA0025ZZ
ALKIA2487ZZ
JMKIA0560ZZ
AWKIA1997ZZ
DLK-322
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR HANDLE
10. Remove front gasket (1) and rear gasket (2).
: Front
11. Slide outside handle bracket toward rear of vehicle to remove.
: Front
12. Disconnect the outside handle cable from the outside handle
bracket connection.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• When installing do not reuse front door outside handle bracket screw. Always replace screw with
new ones when removed.
• When installing door key cylinder rod on the LH front door, be sure to rotate door key cylinder rod
holder until a click is felt.
• Check front door lock cable is properly engaged to outside handle bracket.
• After installation, check front door open/close, lock/unlock operation.
REAR DOOR HANDLE
JMKIA5889ZZ
JMKIA5890ZZ
PIIB5815E
DOOR HANDLE
DLK-323
< REMOVAL AND INSTALLATION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR HANDLE : Exploded View
INFOID:0000000009756639
REAR DOOR HANDLE : Removal and Installation - Inside Handle
INFOID:0000000009756640
REMOVAL
1. Remove rear door finisher. Refer to
INT-19, "Removal and Installation"
.
2. Remove inside handle assembly screws (A) and inside handle
assembly (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check rear door lock cables are properly engaged to inside handle.
• After installation, check rear door open/close, lock/unlock operation.
REAR DOOR HANDLE : Removal and Installation - Outside Handle
INFOID:0000000009756641
REMOVAL
1. Fully close rear door glass.
2. Remove rear door finisher. Refer to
INT-19, "Removal and Installation"
.
3. Remove rear door vapor barrier.
1.
Outside handle bracket
2.
Rear gasket
3.
Front gasket
4.
Outside door handle
5.
Outside handle escutcheon
6.
Inside handle assembly
ALKIA2924ZZ
ALKIA2715ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст