Nissan Juke F15. Manual — part 786
FRONT DRIVE SHAFT
FAX-83
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
2WD : Removal and Installation
INFOID:0000000012201561
REMOVAL
Left Side
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor and sensor harness. Refer to
BRC-147, "FRONT WHEEL SENSOR : Exploded
.
3. Remove lock plate from strut assembly. Refer to
BR-25, "FRONT : Removal and Installation"
.
4. Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
5. Remove disc rotor.
CAUTION:
• Put matching marks (A) on the wheel hub assembly and
the disc rotor before removing the disc rotor.
• Never drop disc rotor.
6. Remove cotter pin, and adjusting cap, and then loosen wheel hub lock nut with power tool.
7. Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub assembly from drive shaft.
NOTE:
Use suitable puller, if wheel hub assembly and drive shaft can-
not be separated even after performing the above procedure.
8. Remove wheel hub lock nut.
9. Remove strut assembly from steering knuckle. Refer to
FSU-9, "Removal and Installation"
.
10. Remove drive shaft from wheel hub assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
13. Heat insulator
: Wheel side
: Fill NISSAN Genuine grease or equivalent.
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPDIG0066ZZ
JPDIG0070ZZ
FAX-84
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT
11. Use the drive shaft attachment (A) [SST:KV40107500 ( — )]
and a sliding hammer (B) (commercial service tool) while insert-
ing tip of the drive shaft attachment between shaft and transaxle
assembly, and then remove drive shaft from transaxle assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle when
removing drive shaft. Also be careful not to overextend
slide joint.
• Confirm that the circular clip is attached to the drive shaft.
Right Side
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor and sensor harness. Refer to
BRC-147, "FRONT WHEEL SENSOR : Exploded
.
3. Remove lock plate from strut assembly. Refer to
BR-25, "FRONT : Removal and Installation"
4. Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
5. Remove disc rotor.
CAUTION:
• Put matching marks (A) on the wheel hub assembly and
the disc rotor before removing the disc rotor.
• Never drop disc rotor.
6. Remove cotter pin, and adjusting cap, and then loosen wheel hub lock nut with power tool.
7. Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub assembly from drive shaft.
NOTE:
Use suitable puller, if wheel hub assembly and drive shaft can-
not be separated even after performing the above procedure.
8. Remove wheel hub lock nut.
9. Remove strut assembly from steering knuckle. Refer to
FSU-9, "Removal and Installation"
10. Remove drive shaft from wheel hub assembly.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for joint sub-assembly, shaft and the other
parts.
11. Remove plate from support bearing bracket.
12. Remove drive shaft assembly from transaxle assembly.
JPDIF0004ZZ
JPDIG0066ZZ
JPDIG0070ZZ
FRONT DRIVE SHAFT
FAX-85
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
CAUTION:
Never place drive shaft joint at an extreme angle when removing drive shaft. Also be careful not to
overextend slide joint.
13. Remove heat insulator.
14. Remove support bearing bracket.
INSTALLATION
Note the following, and install in the reverse order of removal.
Left Side
• Always replace differential side oil seal with new one when installing drive shaft. Refer to
• Place the protector (A) [SST:KV38107900 ( — )] onto transaxle
assembly to prevent damage to the differential side oil seal while
inserting drive shaft. Slide drive shaft sliding joint and tap with a
hammer to install securely.
CAUTION:
• Check that circular clip is completely engaged.
• Never reuse circular clip.
• Never reuse differential side oil seal.
• Clean the matching surface of wheel hub lock nut and wheel hub assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
• Clean the matching surface of drive shaft and wheel hub assembly.
And then apply paste [service parts (440037S000)] to surface (A)
of joint sub-assembly of drive shaft.
CAUTION:
Apply paste to cover entire flat surface of joint sub-assembly
of drive shaft.
• Use the following torque range for tightening the wheel hub lock nut.
CAUTION:
• Since the drive shaft is assembled by press-fitting, use the tightening torque range for the wheel
hub lock nut.
• Be sure to use torque wrench to tighten the wheel hub lock nut. Never use a power tool.
• Never reuse wheel hub lock nut.
NOTE:
Wheel hub lock nut tightening torque does not over torque for avoiding axle noise, and does not less than
torque for avoiding looseness.
• Align the matching marks that have been made during removal when reusing the disc rotor.
JPDIF0023ZZ
Amount paste
: 1.0 – 3.0 g (0.04 – 0.10 oz)
JSDIA2844ZZ
: 180 – 185 N·m (18.4 – 18.8 kg-m, 133 – 136 ft-lb)
FAX-86
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT DRIVE SHAFT
• When installing a cotter pin (1) and adjusting cap (2), securely
bend the basal portion to prevent rattles.
CAUTION:
Never reuse cotter pin.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub assembly and steering knuckle.
• Perform inspection after installation. Refer to
Right Side
• Always replace differential side oil seal with new one when installing drive shaft. Refer to
• Install support bearing bracket (1) in following procedure,
- Temporarily tighten mounting bolts (A), (B), (C), then tighten them
to specified torque.
- Set plate (2) so that notch (D) becomes upper side. Temporarily
tighten mounting bolts (E), (F), then tighten them to specified
torque.
CAUTION:
Never reuse plate.
• Place the protector (A) [SST:KV38107900 ( — )] onto transaxle
assembly to prevent damage to the differential side oil seal while
inserting drive shaft. Slide drive shaft sliding joint and tap with a
hammer to install securely.
CAUTION:
Never reuse differential oil seal.
• To install mounting nuts of the heat insulator (1), temporarily
tighten them in numerical order shown in the figure and tighten
them to the specified torque.
• Clean the matching surface of wheel hub lock nut and wheel hub assembly.
CAUTION:
Never apply lubricating oil to these matching surface.
JPDIF0295ZZ
JSDIA2132ZZ
JSDIA6354ZZ
JPDIF0312ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст