Nissan Juke (2016 year). Service Repair Manual — part 672
DIFFERENTIAL SIDE OIL SEAL
TM-569
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
A hub cap (Part No. 43234 1HA0A) can be used as a substitute for drift. To use a hub cap, be sure to pre-
pare a new one specifically for patting seal.
4. Remove masking tape.
5. Adjust as instructed below to optimize the protrusion size and parallelism.
CAUTION:
If differential side oil seal is inserted deeper than the reference value, use a new differential side
oil seal and perform the steps again.
• Protrusion size (A)
CAUTION:
Protrusion must fall within
±
0.5mm (0.020 in) of calcu-
lated size.
• Parallelism at four diagonal points (
)
CAUTION:
The difference among four diagonal points must be within
0.3 mm (0.012 in).
NOTE:
If differential side oil seal is uneven while installing, tilt suitable
tool.
6. Check that the protrusion size and parallelism are adequate.
Differential Side Oil Seal (Converter housing Side) (AWD Models)
CAUTION:
• Never reuse differential side oil seal.
• Apply ATF to the differential side oil seal lip and around the oil seal.
Install differential side oil seal evenly using a drift [outer diameter: 60
mm (2.36 in)] so that differential side oil seal protrudes by the dimen-
sion (A) respectfully.
NOTE:
The reference is the installation direction of the differential side oil
seal.
Inspection and Adjustment
INFOID:0000000012201265
INSPECTION AFTER INSTALLATION
Drive the vehicle and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
JSDIA4815ZZ
JSDIA4814ZZ
Dimension (A)
: Height difference from case end sur-
face is within 1.0
±
0.5 mm (0.039
±
0.020 in).
JSDIA6885ZZ
Revision: November 2015
2016 JUKE
TM-570
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
WATER HOSE
WATER HOSE
Exploded View
INFOID:0000000012201266
Removal and Installation
INFOID:0000000012201267
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform when the engine is cold.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove battery. Refer to
PG-105, "Removal and Installation"
.
2. Remove ECM and bracket as a set. Refer to
EC-1256, "Removal and Installation"
3. Remove CVT fluid charging pipe. Refer to
4. Remove water hoses.
5. Remove water tube assembly
INSTALLATION
1.
Thermostat housing
2.
Hose clamp
3.
Water hose A
4.
Clip
5.
Water tube assembly
6.
Water hose B
7.
Water hose C
8.
CVT oil warmer
9.
Transaxle assembly
10. Water outlet
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA6063GB
Revision: November 2015
2016 JUKE
WATER HOSE
TM-571
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse hose clamp and clip.
• Securely install the water hose clip to the converter housing.
• Refer to the following when installing water hoses.
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
Inspection
INFOID:0000000012201268
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of engine coolant.
Hose (1)
Installation side
tube (2)
Direction of paint
mark
Hose insertion
depth (L)
Water hose A
Thermostat hous-
ing
Frontward
Hose end reaches
the 2-stage bulge.
CVT oil warmer
Water hose B
CVT oil warmer
Water tube as-
sembly
Water hose C
Water tube as-
sembly
Water outlet
Leftward
JSDIA2459ZZ
Hose (1)
Installation side tube
(2)
Hose clamp (3)
Direction of tab
Clamping position
(A)
Water hose A
Thermostat housing
Frontward
5 – 7 mm (0.20 –
0.28 in) from hose
end
CVT oil warmer
Water hose B
CVT oil warmer
Water tube assem-
bly
Water hose C
Water tube assem-
bly
Water outlet
Leftward
JSDIA2424ZZ
Revision: November 2015
2016 JUKE
TM-572
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
FLUID COOLER HOSE
FLUID COOLER HOSE
Exploded View
INFOID:0000000012201269
Removal and Installation
INFOID:0000000012201270
REMOVAL
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1. Remove fluid cooler hose A and B.
2. Remove fluid cooler tube A and B.
INSTALLATION
Note the followings and Installation is in the reverse order of removal.
CAUTION:
Never reuse hose clamp, and copper washer.
1.
Transaxle assembly
2.
Copper washer
3.
Fluid cooler tube B
4.
Hose clamp
5.
Fluid cooler hose B
6.
Fluid cooler tube A
7.
Fluid cooler hose A
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA6978GB
Revision: November 2015
2016 JUKE
FLUID COOLER HOSE
TM-573
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Refer to the followings when installing CVT fluid cooler tubes.
• When installing fluid cooler tube A (1) and fluid cooler tube B (2) to
transaxle assembly, contact fluid cooler tubes stopper (A) and (B)
to transaxle case.
• Refer to the followings when installing fluid cooler hose.
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
Inspection
INFOID:0000000012201271
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
JSDIA6070ZZ
Hose (1)
Installation side tube (2)
Direction of paint mark
Hose insertion depth (L)
Fluid cooler hose A
CVT fluid cooler tube A
Frontward
(A): Hose end reaches the 2-stage bulge.
CVT oil warmer
(B): Hose end reaches the end of tube.
Fluid cooler hose B
CVT fluid cooler tube B
(A): Hose end reaches the 2-stage bulge.
CVT oil warmer
(B): Hose end reaches the end of tube.
JSDIA2355ZZ
Hose (1)
Installation side
tube (2)
Hose clamp (3)
Direction of tab
Clamping position
Fluid cooler
hose A
CVT oil warmer
Frontward
5 - 9 mm. (0.20 - 0.35
in) (A) from hose end
CVT fluid cooler
tube A
Fluid cooler
hose B
CVT oil warmer
CVT fluid cooler
tube B
JSDIA2424ZZ
Revision: November 2015
2016 JUKE
TM-574
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CVT OIL WARMER
CVT OIL WARMER
Exploded View
INFOID:0000000012201272
Removal and Installation
INFOID:0000000012201273
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform when the engine is cold.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid/coolant
from spilling.
1. Remove ECM and bracket as a set. Refer to
EC-1256, "Removal and Installation"
2. Pull out water hoses from CVT oil warmer. Refer to
TM-570, "Removal and Installation"
.
3. Pull out fluid cooler hoses from CVT oil warmer. Refer to
TM-572, "Removal and Installation"
4. Remove mounting bolt (
) and remove CVT oil warmer from
transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
1.
Transaxle assembly
2.
CVT oil warmer
: N·m (kg-m, in-lb)
JSDIA6066GB
JSDIA6620ZZ
Revision: November 2015
2016 JUKE
CVT OIL WARMER
TM-575
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Inspection
INFOID:0000000012201274
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid and engine coolant.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
Revision: November 2015
2016 JUKE
TM-576
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
PLUG
PLUG
Description
INFOID:0000000012201275
Replace the O-ring if oil leakage or exudes from the plug.
Exploded View
INFOID:0000000012201276
Removal and Installation
INFOID:0000000012201277
REMOVAL
1. Remove front fender protector (LH). Refer to
EXT-31, "Removal and Installation"
.
2. Remove the plug and O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Never reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection and Adjustment
INFOID:0000000012201278
INSPECTION AFTER INSTALLATION
Start the engine and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
1.
Transaxle assembly
2.
O-ring
3.
Plug
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Apply CVT fluid
JSDIA3622GB
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст