Nissan Juke (2016 year). Service Repair Manual — part 641
TM-320
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
CONTROL CABLE
5. Remove the lock plate (1).
6. Remove center muffler from the mounting rubber and lower the
center muffler downward. Refer to
.
7. Lift up the heat plate.
8. Remove the control cable (1) from the bracket (2).
9. Remove the control cable from the vehicle.
10. Remove bracket.
INSTALLATION
Note the following, and install in the reverse order of removal.
• From below the vehicle, press the grommet (A) into place until the
pawls (B) make a click sound.
CAUTION:
• Place the grommet on the floor, then fasten it in place from
below the vehicle.
• Check that pulling down on the grommet does not discon-
nect it.
• Pay attention to the following when connecting the control cable to the CVT shift selector.
1. When connecting the control cable (1) to the CVT shift selector
assembly (2), face the grooved surface of the rib (A) up and
insert the control cable until it stops.
JSDIA2643ZZ
:Vehicle front
JPDIA0107ZZ
JSDIA1809ZZ
JSDIA1624ZZ
Revision: November 2015
2016 JUKE
CONTROL CABLE
TM-321
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2. Install the socket (A) onto the CVT shift selector.
CAUTION:
• Place the socket onto the CVT shift lever, then fasten it in
place from above.
• Check that the pulling on the socket does not disconnect
it.
Inspection
INFOID:0000000012201015
INSPECTION AFTER INSTALLATION
Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
JSDIA1810ZZ
Revision: November 2015
2016 JUKE
TM-322
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
PADDLE SHIFTER
PADDLE SHIFTER
Exploded View
INFOID:0000000012201016
Removal and Installation
INFOID:0000000012201017
REMOVAL
1. Park the vehicle on a level surface.
2. Remove the driver air bag module. Refer to
SR-12, "Removal and Installation"
3. Remove the steering wheel. Refer to
ST-9, "Removal and Installation"
4. Remove the column cover. Refer to
IP-13, "Removal and Installation"
1.
Steering column assembly
2.
Paddle shifter (shift-down switch)
3.
Paddle shifter (shift-up switch)
: N·m (kg-m, in-lb)
AWDIA0557GB
Revision: November 2015
2016 JUKE
PADDLE SHIFTER
TM-323
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
5. Remove the paddle shifter connector (C) and (D) from paddle
shifter.
6. Remove the paddle shifter mounting bolts (E) and nuts (F).
7. Remove the paddle shifter from the steering column assembly.
INSTALLATION
Installation is in the reverse order of removal.
A
: Side of paddle shifter (shift-down switch)
B
: Side of paddle shifter (shift-up switch)
AWDIA0563ZZ
Revision: November 2015
2016 JUKE
TM-324
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
KEY INTERLOCK CABLE
KEY INTERLOCK CABLE
Exploded View
INFOID:0000000012201018
Removal and Installation
INFOID:0000000012201019
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1. Shift the selector lever to the “N” position.
2. Remove the selector lever knob. Refer to
TM-317, "Disassembly and Assembly"
3. Shift the selector lever to the “P” position.
4. Remove the center console. Refer to
IP-24, "Removal and Installation"
.
5. Press the pawls (B) of the key interlock cable slider (A) while
sliding it in the direction of the casing cap (C), and separate the
adjusting holder (D) and slider.
6. Remove the key interlock cable from the CVT shift selector.
7. Remove the steering column lower cover and driver instrument
lower panel. Refer to
IP-13, "Removal and Installation"
.
1.
CVT shift selector assembly
2.
Key interlock cable
A:
Key cylinder
B:
Clip
C:
Clip
JSDIA2448ZZ
E
:Key interlock rod
JSDIA1797ZZ
Revision: November 2015
2016 JUKE
KEY INTERLOCK CABLE
TM-325
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
8. Lift clip (A) in the direction of the arrow (
C) and remove in the
direction of the arrow (
D).
9. Disconnect the key interlock cable from the key cylinder.
10. Disengage the clip and disconnect the key interlock cable from
the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the adjusting holder (A) onto the key interlock rod (B), then
install the casing cap (C) onto the CVT shift selector cable bracket
(D).
CAUTION:
• When installing the key interlock cable, never bend or twist
the cable forcefully.
• After connecting the key interlock cable to the CVT shift
selector cable bracket, be sure to check that the casing cap
is completely fastened to the cable bracket. If the casing cap
is easily displaced, replace the key interlock cable.
• While pressing the detent rod (B) down, slide the key interlock
cable slider (A) toward the key interlock rod (D) side, and install the
adjusting holder (C) and key interlock rod.
CAUTION:
• Never squeeze the pawls on the key interlock cable slider
when holding the slider.
• Never apply force in a perpendicular direction to the key
interlock rod when sliding the slider.
Inspection
INFOID:0000000012201020
INSPECTION AFTER INSTALLATION
• Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
• The key can be removed only when the selector lever is in the “P” position.
• It must not be possible to turn the ignition switch to LOCK when the selector lever is not in the “P” position.
1
:Key interlock cable
B
:Key cylinder
JSDIA1798ZZ
JSDIA1799ZZ
JSDIA1800ZZ
Revision: November 2015
2016 JUKE
TM-326
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
TRANSMISSION RANGE SWITCH
TRANSMISSION RANGE SWITCH
Exploded View
INFOID:0000000012201021
Removal and Installation
INFOID:0000000012201022
REMOVAL
1. Remove battery. Refer to
PG-105, "Removal and Installation"
.
2. Remove transmission range switch connector.
3. Remove control cable. Refer to
TM-319, "Removal and Installation"
.
4. Remove transmission range switch from transaxle assembly.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000012201023
ADJUSTMENT OF TRANSMISSION RANGE SWITCH
1. Move selector lever to “N” position.
2. Remove control cable from manual lever.
1.
Transmission range switch
2.
Transaxle assembly
: N·m (kg-m, in-lb)
JSDIA2397GB
Revision: November 2015
2016 JUKE
TRANSMISSION RANGE SWITCH
TM-327
< REMOVAL AND INSTALLATION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
3. Loosen mounting bolts (
) of transmission range switch. Insert
a pin (
φ
4 mm) into the adjusting holes (A) on both transmission
range switch and manual lever for adjusting the position.
4. Tighten mounting bolts of transmission range switch.
5. Connect control cable on manual lever. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing the CVT shift selector. Refer to
TM-233, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLAION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-233, "Inspection and Adjustment"
JSDIA2398ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст