Nissan Juke (2016 year). Service Repair Manual — part 506
PARKING BRAKE CONTROL
PB-7
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
Removal and Installation
INFOID:0000000012200167
REMOVAL
1. Remove rear tires with power tool.
2. Remove the center console assembly. Refer to
IP-24, "Removal and Installation"
3. Disconnect the parking brake switch harness connector.
4. Remove adjusting nut (1) and loosen front cable.
5. Remove the parking brake lever assembly.
1.
Parking brake lever assembly
2.
Adjusting nut
3.
Parking brake switch
4.
Front cable
5.
Rear cable (LH)
6.
Rear cable (RH)
: Apply multi-purpose grease.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JSFIA0466GB
JPFIB0131ZZ
Revision: November 2015
2016 JUKE
PB-8
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
6. Remove rear cable with the following procedure.
a. Pull equalizer (A) of the front cable (1) in a rearward direction.
b. Push the equalizer upward to remove the rear cable (2).
7. Remove center muffler and heat plate. Refer to
8. Remove brake shoe, and remove rear cable from toggle lever.
9. Remove rear cable mounting bolts, pull out rear cable from vehi-
cle.
10. Press the pawl (1) to remove the rear cable from the vehicle.
INSTALLATION
Note the following, install in the reverse order of the removal.
• Never reuse adjusting nut.
• Perform adjustment after installation. Refer to
PB-4, "Inspection and Adjustment"
Adjustment
INFOID:0000000012200168
ADJUSTMENT AFTER INSTALLATION
Adjust the parking brake lever stroke. Refer to
PB-4, "Inspection and Adjustment"
JPFIB0129ZZ
JPFIB0130ZZ
Revision: November 2015
2016 JUKE
PARKING BRAKE SHOE
PB-9
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SHOE
Exploded View
INFOID:0000000012200169
Removal and Installation
INFOID:0000000012200170
REMOVAL
WARNING:
Since dust covering the parking brake has an affect on human body, the dust must be removed with a
dust collector. Never splatter the dust with an air blow gun.
1. Remove rear tires with power tool.
2. Remove disc rotor.
• 2WD: Refer to
RAX-7, "Removal and Installation"
.
• AWD: Refer to
RAX-16, "Removal and Installation"
.
CAUTION:
Parking brake completely in the released position.
1.
Anti-rattle pin
2.
Back plate
3.
Toggle lever
4.
Parking brake shoe
5.
Brake strut
6.
Return spring
7.
Spring
8.
Adjuster
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
JPFIB0086ZZ
Revision: November 2015
2016 JUKE
PB-10
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
3. Remove return spring (1) of the upper side.
4. Remove return spring (1) of the lower side.
5. Remove spring (1).
CAUTION:
Never drop the removed parts.
6. Remove parking brake shoes, adjuster, brake strut and toggle
lever.
CAUTION:
• The parking brake shoes for the front wheels are made of
different materials from those for the rear wheels. Never
misidentify them when removing.
• Never drop the removed parts.
7. Press the rear cable spring (1) against spring tension to remove
rear cable (3) from the clamp (A) of toggle lever (2).
CAUTION:
Never bend rear cable.
8. For the removal of back plate.
• 2WD: Refer to
RAX-7, "Removal and Installation"
.
• AWD: Refer to
RAX-16, "Removal and Installation"
.
INSTALLATION
Note the following, install in the reverse order of removal.
• Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the back plate and brake shoe.
CAUTION:
The parking brake shoes for the front wheels are made of different materials from those for the rear
wheels. Never misidentify them when removing and replacing.
JSFIA0485ZZ
JSFIA0486ZZ
JSFIA0487ZZ
JSFIA0488ZZ
Revision: November 2015
2016 JUKE
PARKING BRAKE SHOE
PB-11
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
• Assemble adjusters so that threaded part is expanded when rotat-
ing it in the direction shown by arrow.
• Shorten adjuster by rotating it.
• When disassembling apply PBC (Poly Butyl Cuprysil) grease or sil-
icone-based grease to threads.
• Check that the component parts of the parking brake shoe are
properly installed.
• Check brake shoe sliding surface and drum inner surface for
grease. Wipe it off if it adhere on the surfaces.
Inspection and Adjustment
INFOID:0000000012200171
INSPECTION AFTER REMOVAL
Lining Thickness Inspection
• Check thickness (A) of lining.
Drum Inner Diameter Inspection
• Check inner diameter (B) of drum.
Other Inspections
Check the following items, and replace the parts if necessary.
• Lining for excessive wear, damage, and peeling.
• Brake shoe sliding surface for excessive wear and damage.
• Anti-rattle pin for excessive wear, damage and rust.
• Return spring and spring for settling, excessive wear, damage, and rust.
A : For right side brake
B : For left side brake
: Vehicle front
: Adjuster expands
JPFIB0087ZZ
JSFIA0489ZZ
A
: Refer to
.
SBR021A
B
: Refer to
.
JPFIB0008ZZ
Revision: November 2015
2016 JUKE
PB-12
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
• Adjuster for smoothness.
• Toggle lever and brake strut for excessive wear, damage and rust.
• Visually check inside of the drum for excessive wear, cracks, and damage with a pair of vernier calipers.
ADJUSTMENT AFTER INSTALLATION
1. Adjust the parking brake lever stroke. Refer to
PB-4, "Inspection and Adjustment"
.
2. Rotate the disc rotor to check that there is no drag. Install the plug. If any drag is found, follow the proce-
dure described below.
a. Adjust parking brake stroke again.
b. Check rear disc brake. Refer to
BR-67, "BRAKE CALIPER ASSEMBLY : Inspection"
.
3. Adjust the parking brake shoe. Refer to
Revision: November 2015
2016 JUKE
SERVICE DATA AND SPECIFICATIONS (SDS)
PB-13
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Parking Drum Brake
INFOID:0000000012200172
Unit: mm (in)
Parking Brake Control
INFOID:0000000012200173
Item
Limit
Brake lining
1.5 (0.059)
Drum (disc of inner diameter)
173 (6.81)
Item
Standard
Number of notches [under force of 196 N (20 kg, 44 lb)]
9
−
10 notches
Number of notches when brake warning lamp turns ON
1 notch
Revision: November 2015
2016 JUKE
PCS
PCS-1
ELECTRICAL & POWER CONTROL
C
D
E
F
G
H
I
J
K
L
B
SECTION
PCS
A
O
P
N
CONTENTS
POWER CONTROL SYSTEM
IPDM E/R
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
RELAY CONTROL SYSTEM . . . . . . . . . ..
RELAY CONTROL SYSTEM : System Diagram . ..
RELAY CONTROL SYSTEM : System Descrip-
tion . . . . . . . . . . . . . . . . . . ....
RELAY CONTROL SYSTEM : Fail-safe . . . . ...
POWER CONTROL SYSTEM . . . . . . . . .....
POWER CONTROL SYSTEM : System Diagram .
POWER CONTROL SYSTEM : System Descrip-
tion . . . . . . . . . . . . . . . . . . ..
SIGNAL BUFFER SYSTEM . . . . . . . . . ..
SIGNAL BUFFER SYSTEM : System Diagram . ..
SIGNAL BUFFER SYSTEM : System Description .
POWER CONSUMPTION CONTROL SYSTEM . ...
POWER CONSUMPTION CONTROL SYSTEM :
System Diagram . . . . . . . . . . . . . ..
POWER CONSUMPTION CONTROL SYSTEM :
System Description . . . . . . . . . . . . .
DIAGNOSIS SYSTEM (IPDM E/R) . . . . . .
Diagnosis Description . . . . . . . . . . . .
CONSULT Function (IPDM E/R) . . . . . . . .
ECU DIAGNOSIS INFORMATION . . . ..
IPDM E/R . . . . . . . . . . . . . . ...
Reference Value . . . . . . . . . . . . . ..
Fail-safe . . . . . . . . . . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ...
WIRING DIAGRAM . . . . . . . . . ..
IPDM E/R . . . . . . . . . . . . . . ...
Wiring Diagram . . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
U1000 CAN COMM CIRCUIT . . . . . . ...
Description . . . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
B2098 IGNITION RELAY ON STUCK . . . ..
Description . . . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
B2099 IGNITION RELAY OFF STUCK . . .
Description . . . . . . . . . . . . . . . ...
DTC Logic . . . . . . . . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
POWER SUPPLY AND GROUND CIRCUIT .
Diagnosis Procedure . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . ...
IPDM E/R . . . . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
POWER DISTRIBUTION SYSTEM
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . .
Precautions for Removing Battery Terminal . . .
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст