Nissan Juke (2016 year). Service Repair Manual — part 505
MWI-64
< REMOVAL AND INSTALLATION >
COMBINATION METER
REMOVAL AND INSTALLATION
COMBINATION METER
Exploded View
INFOID:0000000012201350
REMOVAL
.
DISASSEMBLY
Removal and Installation
INFOID:0000000012201351
REMOVAL
1. Remove cluster lid A. Refer to
IP-13, "Removal and Installation"
2. Remove the mounting screws of the combination meter.
3. Pull the combination meter straight to disengage resin clips.
(The figure shows the clip positions on the back of the combina-
tion meter.)
CAUTION:
Never damage the front cover.
1.
Front cover
2.
Unified meter control unit
JSNIA3219ZZ
JSNIA3208ZZ
Revision: November 2015
2016 JUKE
MWI
COMBINATION METER
MWI-65
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
4. Turn the lower part of the combination meter in the direction of
the arrow to remove the combination meter from the instrument
panel assembly.
CAUTION:
Never damage the front cover.
5. Remove connector to remove the combination meter.
CAUTION:
Never damage the front cover.
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000012201352
DISASSEMBLY
1. Disengage the pawls (2 on the sides, 3 on the lower part) of the combination meter.
2. Insert the removal tool into the clearance (in the order of A, B)
between the front cover and the meter control unit. Remove 4
pawls on the upper side of the front cover by turning the tool
while increasing the clearance.
CAUTION:
Wrap the removal tools with protective tape to prevent
scratches.
3. Pull the front cover straight to remove it from the meter control unit assembly.
CAUTION:
Never damage the front cover.
Never touch the pointer and the crystalline liquid.
ASSEMBLY
Install the front cover straight to the meter control unit assembly and engage all the pawl.
CAUTION:
Never damage the front cover.
JSNIA3546ZZ
JSNIA3210ZZ
Revision: November 2015
2016 JUKE
PB-1
BRAKES
C
D
E
G
H
I
J
K
L
M
SECTION
PB
A
B
PB
N
O
P
CONTENTS
PARKING BRAKE SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing Battery Terminal . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
PARKING BRAKE SYSTEM . . . . . . . ...
Inspection and Adjustment . . . . . . . . . ....
PARKING BRAKE SHOE . . . . . . . . ...
Adjustment . . . . . . . . . . . . . . . ....
REMOVAL AND INSTALLATION . . . .
PARKING BRAKE CONTROL . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Adjustment . . . . . . . . . . . . . . . ....
PARKING BRAKE SHOE . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Inspection and Adjustment . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Parking Drum Brake . . . . . . . . . . . .
Parking Brake Control . . . . . . . . . . . .
Revision: November 2015
2016 JUKE
PB-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Removing Battery Terminal
INFOID:0000000012200162
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
Revision: November 2015
2016 JUKE
PREPARATION
PB-3
< PREPARATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000012200163
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
Revision: November 2015
2016 JUKE
PB-4
< PERIODIC MAINTENANCE >
PARKING BRAKE SYSTEM
PERIODIC MAINTENANCE
PARKING BRAKE SYSTEM
Inspection and Adjustment
INFOID:0000000012200164
INSPECTION
Lever Stroke
1. Operate the parking brake lever with a force of 196 N (20 kg, 44 lb). Check that the lever stroke is within
the specified number of notches. (Check it by listening to the clicks of the ratchet.)
2. When brake warning lamp turns ON, check that the lever stroke is within the specified number of notches.
(Check it by listening to the clicks of the ratchet.)
Inspect Components
• Check each component for installation condition such as looseness.
• Check the parking brake lever assembly for bend, damage and cracks. Replace if necessary.
• Check the cables and equalizer for wear, damage and cracks. Replace if necessary.
• Check the parking brake switch, and replace it if necessary. Refer to
BRC-116, "Component Inspection"
.
ADJUSTMENT
1. Remove rear tires with power tool.
2. Fix the disc rotor using wheel nut.
3. Remove the console mask. Refer to
IP-24, "Removal and Installation"
.
4. Remove the adjusting hole plug from the disc rotor. Turn the
adjuster (1) in the direction (A) as shown in the figure using a
suitable tool until the disc rotor is locked.
5. Turn back the adjuster 7 notches from the locked position.
6. Rotate the disc rotor to check that there is no drag. Install the
adjuster hole plug. Refer to
PB-11, "Inspection and Adjustment"
.
7. Adjust the cable with the following procedure.
a. Operate and maintain the parking brake lever with a force of 400 N (41 kg, 90 lb) for 15 minutes or more.
b. Adjust the parking brake lever stroke by turning the adjusting nut
(1) with a socket wrench.
CAUTION:
Make sure to securely depress the brake pedal.
c.
Operate the parking brake lever with a force of 196 N (20 kg,
44lb). Check that the lever stroke is within the specified number
of notches. (Check it by listening to the clicks of the ratchet.)
d. Rotate the disc rotor to check that there is no drag. Refer to
11, "Inspection and Adjustment"
.
Number of notches
: Refer to
PB-13, "Parking Brake Control"
Number of notches
: Refer to
PB-13, "Parking Brake Control"
JPFIB0088ZZ
Number of notches
: Refer to
JPFIB0131ZZ
Revision: November 2015
2016 JUKE
PARKING BRAKE SHOE
PB-5
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SHOE
Adjustment
INFOID:0000000012200165
1. Adjust parking brake lever stroke. Refer to
PB-4, "Inspection and Adjustment"
.
2. Perform parking brake break-in (drag on) operation by driving vehicle under the following conditions:
• Drive forward
• Vehicle speed: Approx. 43 km/h (27 MPH) set (constant and forward)
• Parking brake operating force: 125 N (12.8 kg, 28.1 lb) set contact
• Time: Approx. 8 sec.
CAUTION:
To prevent lining from getting too hot, allow a cool off period of approximately 5 minutes after
every break-in operation.
3. After the break-in procedure, check parking brake lever stroke of parking brake.
CAUTION:
If it is out of the specification, adjust again. Refer to
PB-4, "Inspection and Adjustment"
Revision: November 2015
2016 JUKE
PB-6
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
REMOVAL AND INSTALLATION
PARKING BRAKE CONTROL
Exploded View
INFOID:0000000012200166
2WD
AWD
1.
Parking brake lever assembly
2.
Adjusting nut
3.
Parking brake switch
4.
Front cable
5.
Rear cable (LH)
6.
Rear cable (RH)
: Apply multi-purpose grease.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JSFIA0603GB
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст