Nissan Juke (2016 year). Service Repair Manual — part 487
LU-28
< PERIODIC MAINTENANCE >
[MR EXCEPT FOR NISMO RS MODELS]
ENGINE OIL
PERIODIC MAINTENANCE
ENGINE OIL
Inspection
INFOID:0000000012197495
ENGINE OIL LEVEL AND CONTAMINATION
• Check engine oil level on a horizontal area before starting the engine. Wait for 10 minutes or more to check
oil level when the engine is started.
• Check that oil level is within the range between level L and level H.
• Fill with engine oil if oil level is outside the range.
• Check for white contamination or significant dirt in the engine oil.
• If the oil contains white contamination, the most likely cause is con-
tamination from engine coolant. Repair the cause of the contami-
nation.
• When inserting the oil level gauge into the oil level gauge guide,
apply engine oil to the rubber seal on the grip.
ENGINE OIL LEAKAGE
Check for engine oil leakage at the following parts.
• Oil pan
• Oil pan drain plug
• Oil filter
• Oil cooler
• Oil pressure sensor
• Oil temperature sensor
• Front cover
• VTC cover
• Intake valve timing control solenoid valve
• Intake valve timing intermediate-lock control solenoid valve
• Exhaust valve timing control solenoid valve
• Turbocharger assembly
• Turbocharger oil tube and hose
• Mating surface of cylinder head and rocker cover
• Mating surface of high-pressure fuel pump and camshaft bracket
• Mating surface of camshaft bracket and cylinder head
• Mating surface of cylinder block and cylinder head
• Crankshaft oil seal (front, rear)
ENGINE OIL PRESSURE CHECK
CAUTION:
Be careful not to get burned, as engine oil may be hot.
1. Remove the oil pressure sensor (1).
CAUTION:
Handle parts carefully and never subject them to impact.
2. Check the engine oil level.
A : Level must be within this range.
JPBIA0554ZZ
: Engine front
JSBIA5728ZZ
Revision: November 2015
2016 JUKE
ENGINE OIL
LU-29
< PERIODIC MAINTENANCE >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
3. Install oil pressure gauge [SST: ST25051001 (J-25695-1)] (A)
and hose [SST: ST25052000 (J-25695-2)] (B).
4. Start engine and warm it up to normal operating temperature.
5. Check oil pressure with engine running under no-load.
NOTE:
When engine oil temperature is low, engine oil pressure becomes high.
If difference is extreme, check oil passage and oil pump for oil leakage.
6. After the inspections, install oil pressure sensor as follows:
a. Remove old liquid gasket adhering to oil pressure sensor and engine.
b. Apply liquid gasket and tighten oil pressure sensor to specification.
Use Genuine RTV Silicon Sealant or equivalent.
c. Check engine oil level.
d. After warming up engine, check that there is no leakage of engine oil with running engine.
e. Check engine oil level.
f.
After warming up engine, check that there is no leakage of engine oil with running engine.
Draining
INFOID:0000000012197496
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1. Warm up the engine, and check for engine oil leakage from engine components. Refer to
2. Stop the engine and wait for 10 minutes.
3. Loosen oil filler cap.
4. Remove drain plug and then drain engine oil.
Refilling
INFOID:0000000012197497
1. Install drain plug with new drain plug washer. Refer to
.
CAUTION:
Be sure to clean drain plug and install with new drain plug washer.
2. Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-11, "Fluids and Lubricants"
JPBIA0074ZZ
Engine oil pressure
: Refer to
Tightening torque
: Refer to
Tightening torque
: Refer to
Engine oil capacity
: Refer to
LU-38, "Periodical Maintenance Specification"
Revision: November 2015
2016 JUKE
LU-30
< PERIODIC MAINTENANCE >
[MR EXCEPT FOR NISMO RS MODELS]
ENGINE OIL
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3. Warm up engine and check area around drain plug and oil filter for engine oil leakage.
4. Stop engine and wait for 10 minutes.
5. Check the engine oil level. Refer to
.
Revision: November 2015
2016 JUKE
OIL COOLER
LU-31
< REMOVAL AND INSTALLATION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
REMOVAL AND INSTALLATION
OIL COOLER
Exploded View
INFOID:0000000012197498
M/T models
JSBIA5996GB
1.
Clamp
2.
Water hose
3.
Oil cooler
4.
Water hose
5.
O-ring
6.
Hose clip
7.
Water hose bracket
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
Revision: November 2015
2016 JUKE
LU-32
< REMOVAL AND INSTALLATION >
[MR EXCEPT FOR NISMO RS MODELS]
OIL COOLER
CVT models
Removal and Installation
INFOID:0000000012197499
REMOVAL
1. Drain coolant. Refer to
CAUTION:
Allow the engine to cool before beginning.
2. Remove the front bumper. Refer to
EXT-17, "Removal and Installation"
.
3. Remove the charge air cooler. Refer to
EM-194, "Removal and Installation"
4. Disconnect each water hose.
5. Remove the oil cooler.
JSBIA5722GB
1.
Clamp
2.
Water hose
3.
Oil cooler
4.
Water hose
5.
O-ring
A.
To CVT fluid warmer
B.
To multi-way valve
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
Revision: November 2015
2016 JUKE
OIL COOLER
LU-33
< REMOVAL AND INSTALLATION >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
• Loosen bolts in the reverse order of the numerical order as
shown in the figure.
INSTALLATION
Note the following, and install in the reverse order of removal.
Oil Cooler
CAUTION:
Never reuse-ring. Always replace it with a new one.
• Tighten the oil cooler mounting bolts in numerical order as shown
in the figure.
Inspection
INFOID:0000000012197500
INSPECTION AFTER REMOVAL
Check visually and by other means for cracks or damage of the oil cooler. If any abnormality is found, replace
the oil cooler.
INSPECTION AFTER INSTALLATION
1. Use the oil level gauge and check that the oil level is within the standard. Refer to
2. Check the coolant level. Refer to
3. Start the engine. Check for engine oil or coolant leakage.
4. Stop the engine. After stopping it, leave it for 10 minutes or more.
5. Check the engine oil level and coolant level again. Fill or adjust fluid levels if necessary.
JSBIA5723ZZ
JSBIA5723ZZ
Revision: November 2015
2016 JUKE
LU-34
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR EXCEPT FOR NISMO RS MODELS]
OIL PUMP
UNIT DISASSEMBLY AND ASSEMBLY
OIL PUMP
Exploded View
INFOID:0000000012197501
1.
O-ring
2.
Oil pan (upper)
3.
Oil pump drive chain tensioner
4.
Oil pump drive chain
5.
Crankshaft sprocket
6.
Oil pump sprocket
7.
O-ring
8.
Oil pump
9.
Oil pan drain plug
10. Drain plug washer
11. Oil pan (lower)
12. O-ring
13. Oil filter
14. Oil filter stud
15. O-ring
16.
Engine oil pressure control solenoid
valve
17. O-ring
18. Oil level gauge guide
19. Oil level gauge
20. Crankshaft position sensor
21. O-ring
22. Gasket
23. Plug
24. Rear oil seal
A.
.
B.
Oil pan side
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Should be lubricated with oil.
: Sealing point
, : Indicates that the parts is connected at points with same symbols in actual vehicle.
JSBIA5724GB
Revision: November 2015
2016 JUKE
OIL PUMP
LU-35
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR EXCEPT FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
Removal and Installation
INFOID:0000000012197502
REMOVAL
1. Remove the engine unit by lowering it from the vehicle. Refer to
EM-217, "2WD : Removal and Installa-
EM-221, "AWD : Removal and Installation"
(AWD).
2. Remove oil pan (lower). Refer to
EM-282, "Removal and Installation"
3. Remove front cover. Refer to
EM-249, "Removal and Installation"
4. Remove the oil pump sprocket with the following procedure.
a. Push the cam (1) of the oil pump drive chain tensioner in the
direction of the arrow (
) as shown in the figure, and then push
the plunger into the tensioner.
b. Insert the stopper pin (A) into the chain tensioner hole (B), and
then fix it in place with the plunger pushed in.
c. Remove the oil pump drive chain tensioner.
d. Hold the oil pump shaft end (A), and then loosen and remove
the oil pump sprocket mounting nut (B).
CAUTION:
• Be sure to hold the end of the shaft.
• The chain tension must not loosen the oil pump sprocket
mounting nut.
e. Remove the oil pump sprocket.
5. Remove oil pump.
JSBIA5725ZZ
JSBIA5726ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст